Dell 966 All In One Photo Printer User Guide - Page 61

Manually Configuring the Adapter in Infrastructure Mode

Get Dell 966 All In One Photo Printer PDF manuals and user guides View all Dell 966 All In One Photo Printer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

d. Select your Wireless Mode. For Infrastructure Mode, select Access an existing network through a wireless router (Infrastructure Mode) - Typical, and then click Next. For additional setup instructions, see Manually Configuring the Adapter in Infrastructure Mode. For Ad-Hoc Mode, select Access other computers directly without using a wireless router (AdHoc Mode), and then click Next. For additional setup instructions, see Manually Configuring the Adapter in Ad-Hoc Mode. 3. Select the appropriate security method, and then click Next. If no security was detected, go to step 5. 4. Enter the appropriate security key(s) for the network, and then click Next. 5. On the Apply and Verify Wireless Settings screen, check each network attribute to make sure the settings are correct, and then click Next to apply the settings. NOTE: Clicking Next prompts the setup utility to verify wireless communication with the printer. The verification process can take up to 120 seconds. 6. Verify that the adapter can communicate over the network. For more information, see Verifying Network Communication. Manually Configuring the Adapter in Infrastructure Mode To set up the adapter in Infrastructure Mode, the setup steps vary based on the security settings you select. If you don't want any security 1. From the Wireless Security Settings screen, select No Security, and then click Next. 2. On the Apply and Verify Wireless Settings screen, check each network attribute to make sure the settings are correct, and then click Next to apply the settings. 3. Verify that the adapter can communicate over the network. For more information, see Verifying Network Communication. If you want to use Wired Equivalent Privacy (WEP) security 1. From the Wireless Security Settings screen, select Wired Equivalent Privacy (WEP), and then click Next. The WEP Security Information screen opens. 2. Enter the appropriate Network Key, and then click Next. 3. On the Apply and Verify Wireless Settings screen, check each network attribute to make sure the settings are correct, and then click Next to apply the settings. 4. Verify that the adapter can communicate over the network. For more information, see Verifying Network Communication. If you want to use Wi-Fi Protected Access (WPA) security 1. From the Wireless Security Settings screen, select Wi-Fi Protected Access (WPA) and then click Next. The WPA Security Information screen opens. 2. Enter the appropriate WPA Network Key, and then click Next.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
d. Select your
Wireless Mode
.
For Infrastructure Mode,
select
Access an existing network through a wireless router
(Infrastructure Mode) - Typical
, and then click
Next
.
For additional setup instructions, see
Manually Configuring the Adapter in Infrastructure Mode
.
For Ad-Hoc Mode,
select
Access other computers directly without using a wireless router (Ad-
Hoc Mode)
, and then click
Next
.
For additional setup instructions, see
Manually Configuring the Adapter in Ad-Hoc Mode
.
3. Select the appropriate security method, and then click
Next
. If no security was detected, go to
step 5
.
4. Enter the appropriate security key(s) for the network, and then click
Next
.
5. On the
Apply and Verify Wireless Settings
screen, check each network attribute to make sure the settings are
correct, and then click
Next
to apply the settings.
NOTE:
Clicking
Next
prompts the setup utility to verify wireless communication with the printer. The
verification process can take up to 120 seconds.
6. Verify that the adapter can communicate over the network. For more information, see
Verifying Network
Communication
.
Manually Configuring the Adapter in Infrastructure Mode
To set up the adapter in Infrastructure Mode, the setup steps vary based on the security settings you select.
If you don't want any security
1. From the
Wireless Security Settings
screen, select
No Security
, and then click
Next
.
2. On the
Apply and Verify Wireless Settings
screen, check each network attribute to make sure the
settings are correct, and then click
Next
to apply the settings.
3. Verify that the adapter can communicate over the network. For more information, see
Verifying Network
Communication
.
If you want to use Wired Equivalent Privacy (WEP) security
1. From the
Wireless Security Settings
screen, select
Wired Equivalent Privacy (WEP)
, and then click
Next
.
The
WEP Security Information
screen opens.
2. Enter the appropriate
Network Key
, and then click
Next
.
3. On the
Apply and Verify Wireless Settings
screen, check each network attribute to make sure the
settings are correct, and then click
Next
to apply the settings.
4. Verify that the adapter can communicate over the network. For more information, see
Verifying Network
Communication
.
If you want to use Wi-Fi Protected Access (WPA) security
1. From the
Wireless Security Settings
screen, select
Wi-Fi Protected Access (WPA)
and then click
Next
.
The
WPA Security Information
screen opens.
2. Enter the appropriate
WPA Network Key
, and then click
Next
.