Dell Inspiron 24 5430 All-in-One Owners Manual
Dell Inspiron 24 5430 All-in-One Manual
 |
View all Dell Inspiron 24 5430 All-in-One manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Inspiron 24 5430 All-in-One manual content summary:
- Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 1
Inspiron 24 5430 All-in-One Owner's Manual Regulatory Model: W29C Regulatory Type: W29C001 January 2024 Rev. A00 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 2
use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2024 Dell Inc. or its subsidiaries. All rights reserved. Dell - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 3
All-in-One 7 Right...7 Front...8 Back...9 Back panel...10 Bottom...11 Service Tag...12 Tilt...12 Retractable camera...13 Inside view of your computer...15 Chapter environment...32 Dell support policy...33 Chapter 4: Working inside your computer 34 Safety instructions...34 Before working inside - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 4
After working inside your computer...37 BitLocker...37 Recommended tools...37 Screw list...38 Major components of Inspiron 24 5430 All-in-One 39 Chapter 5: Removing and installing Customer Replaceable Units (CRUs 42 Stand...42 Removing the stand...42 Installing the stand...43 Back cover...44 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 5
an existing system setup password 109 Clearing CMOS settings...110 Clearing BIOS (System Setup) and System passwords 110 Chapter 9: Troubleshooting...111 Dell SupportAssist Pre-boot System Performance Check diagnostics 111 Running the SupportAssist Pre-Boot System Performance Check 111 System - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 6
Wi-Fi power cycle...114 Chapter 10: Getting help and contacting Dell 115 6 Contents - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 7
Right 1 Views of Inspiron 24 5430 All-in-One Figure 1. Right view 1. USB 3.2 Gen 2 Type-C port Connect devices such as external storage devices and printers. Provides data transfer speeds up to 10 Gbps. NOTE: Connected USB devices will not charge when the computer is turned off or in sleep state. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 8
Front Figure 2. Front view 1. Retractable-camera assembly Enables you to videochat, capture photos, and record videos. This camera can be retracted to protect your privacy. 2. Display panel Provides visual output to the user. 3. Speakers Provides audio output. 8 Views of Inspiron 24 5430 All-in- - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 9
Back Figure 3. Back view 1. Back cover Removable chassis that covers the internal components of your computer. 2. Back panel Connect USB, audio, video, and other devices. 3. Stand Allows the system to be mounted vertically. Views of Inspiron 24 5430 All-in-One 9 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 10
BIOS Deep Sleep control to disabled to start charging when the computer is powered off. 7. USB 3.2 Gen 1 port with Power on/Wake-up support Connect peripherals such as external storage devices and printers. Provides data transfer speeds up to 5 Gbps. Wake the computer from standby with the keyboard - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 11
appear on the screen. For more information, see the Troubleshooting section in the Service Manual at www.dell.com/support/manuals 3. Service Tag label The Service Tag is a unique alphanumeric identifier that enables Dell service technicians to identify the hardware components in your computer and - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 12
Service Tag The service tag is a unique alphanumeric identifier that allows Dell service technicians to identify the hardware components in your computer and access warranty information. Figure 6. Service Tag location Tilt Y stand 12 Views of Inspiron 24 5430 All-in-One - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 13
Isosceles stand Retractable camera Push the top of camera to extend or retract the camera. Extend the camera before use and retract the camera to protect your privacy when not in use. Views of Inspiron 24 5430 All-in-One 13 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 14
14 Views of Inspiron 24 5430 All-in-One - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 15
Inside view of your computer Figure 7. Inside view of your computer 1. Base panel 2. Solid-state drive slot 3. Camera module 4. Coin-cell battery 5. Heat sink 6. Fan 7. Memory module 8. Speaker 9. Media-card reader 10. System board 11. Microphone module 12. Wireless card slot 13. Power-button board - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 16
cover until it snaps into place. Figure 8. Install the stand 2. Connect the keyboard and mouse. NOTE: To connect your wireless keyboard and mouse, find User Guides and other resources for your products at https://www.dell.com/support 16 Set up your Inspiron 24 5430 All-in-One - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 17
Figure 9. Connect the keyboard and mouse 3. Connect to your network using a cable. Set up your Inspiron 24 5430 All-in-One 17 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 18
Figure 10. Connect to a network NOTE: Alternatively, you can connect to a wireless network. 4. Connect the power adapter. 18 Set up your Inspiron 24 5430 All-in-One - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 19
Figure 11. Connect the power adapter . 5. Press the power button. Set up your Inspiron 24 5430 All-in-One 19 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 20
the operating system setup. For Windows: Follow the on-screen instructions to complete the setup. When setting up, Dell Technologies recommends that not connected to the Internet, create an offline account. ● On the Support and Protection screen, enter your contact details. 7. Locate and use Dell - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 21
prevents security threats, monitors, and detects hardware failures. For more information, see SupportAssist for Home PCs User's Guide at www.dell.com/ support/home/product-support/product/dell-supportassist-pcs-tablets/docs. NOTE: In SupportAssist, click the warranty expiry date to renew or upgrade - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 22
depending on the configuration ordered and the manufacturing variability. Stand The following table provides the height, width, depth, and weight of the stand supported by your Inspiron 24 5430 All-in-One Table 4. Stand Description Y stand Isosceles stand Height 96.62 mm (3.81 in.) 97.56 mm - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 23
Y stand Figure 13. Y stand dimensions The following table provides the dimensions of the computer with Y stand installed. Table 5. Y stand dimensions Description Dimensions 414.30 mm (16.31 in.) 199.55 mm (7.86 in.) 390.71 mm (15.38 in.) 228.19 mm (8.98 in.) 440.30 mm (17.34 in.) 539.11 mm ( - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 24
in.) 440.30 mm (17.34 in.) 531.50 mm (20.92 in.) Processor The following table lists the details of the processors that are supported for your Inspiron 24 5430 All-in-One. Table 7. Processor Description Processor type Option one Intel Core 3-100U processor Option two Intel Core 5-120U - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 25
1.40 GHz 5.00 GHz 1.40 GHz 3.80 GHz Not supported 1.80 GHz 5.40 GHz 1.80 GHz 4.00 GHz Not supported Optimized Not supported Not supported Not supported Quiet Not supported Not supported Not supported Ultra Performance 15W to 16W 15W to 16W 15W to 18W NOTE: Processor clock speeds - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 26
in-One. Table 10. External ports Description Network port Values One RJ45 ethernet port USB ports ● Three USB 3.2 Gen 1 ports with Power on/Wake-up support ● One USB 3.2 Gen 2 port with PowerShare ● One USB 3.2 Type-C Gen 2 port Audio port One Universal headset jack Video port ● One HDMI-out - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 27
combo card NOTE: To learn more about the features of different types of M.2 cards, search in the Knowledge Base Resource at www.dell.com/support. Ethernet The following table lists the wired Ethernet Local Area Network (LAN) specifications of your Inspiron 24 5430 All-in-One. Table 12. Ethernet - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 28
24 5430 All-in-One. Your Inspiron 24 5430 All-in-One supports the M.2 2230 solid-state drive as the primary storage device. Table to 1 TB Media-card reader The following table lists the media cards that are supported on your Inspiron 24 5430 All-in-One. Table 16. Media-card reader specifications - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 29
2.07 megapixels Video 1920 x 1080 (FHD) at 30 fps Infrared camera resolution: Still image Not supported Video Not supported Diagonal viewing angle: Camera 82 degrees Infrared camera Not supported Option two One 5 MP RGB + Infrared camera Front camera CMOS sensor technology 4.92 megapixels - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 30
Display type Option one 23.8", Full High Definition (FHD) Option two 23.8", Full High definition (FHD) Touch options Touch support with 10 touch points Not supported Display-panel technology Wide View Angle (WVA) Wide view Angle (WVA) Display-panel dimensions (active area): Height 296.46 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 31
mm x 0.2745 mm 14.11W Anti-glare GPU-Integrated The following table lists the specifications of the integrated Graphics Processing Unit (GPU) supported by your Inspiron 24 5430 All-in-One. Table 20. GPU-Integrated Controller Memory size Processor Intel UHD Graphics Shares system memory Intel - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 32
Table 22. Environmental (continued) Feature Energy-Efficient Power Supply ENV0424 compliant Values Standard Yes NOTE: Wood‐based fiber packaging contains a minimum of 35% recycled content by total weight of wood‐based fiber. Packaging that contains without wood‐based fiber can be claimed as Not - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 33
Dell support policy For information about Dell support policy, search in the Knowledge Base Resource at www.dell.com/support. Specifications of Inspiron 24 5430 All-in-One 33 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 34
and the contacts. CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that is shipped with the product or at - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 35
before performing any disassembly instructions. Observe the following safety same electrical potential. This is done by using a field service electrostatic discharge (ESD) kit. When connecting a bonding that may not be obvious, such as intermittent problems or a shortened product life span. As the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 36
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking between your skin, the ESD mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 37
parts separate from all insulator parts while performing service and that they use anti-static bags for transporting for a stable base, and point your toes out. 2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load. 3. Lift with your legs - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 38
● Phillips screwdriver #0 ● Phillips screwdriver #1 ● Plastic scribe Screw list NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box. This is to ensure that the correct number of screws and correct - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 39
Table 25. Screw list (continued) Component Screw type Microphones M2x3.5 Display panel M3x5 Display panel M3x3 Quantity 4 10 5 Screw image Major components of Inspiron 24 5430 All-in-One The following image shows the major components of Inspiron 24 5430 All-in-One. Working inside your - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 40
Figure 15. Major components of your computer 1. Back cover 2. I/O cover 3. Isosceles stand 4. Wireless antenna 40 Working inside your computer - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 41
5. Heat sink 6. Microphone module 7. Fan 8. System board 9. Speakers 10. Base panel 11. Middle frame 12. Power-button board with USB 13. Hinges 14. Media-card reader 15. Display panel 16. Wireless-card bracket 17. Wireless card 18. Memory module 19. M.2 2230 solid-state drive 20. System-board shield - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 42
the stand over the edge of the surface. It is recommended to remove the stand to avoid accidental damage to the computer display when servicing. Figure 16. Caution for stand NOTE: The following procedure is applicable for both Y stand and Isosceles stand. NOTE: For replacement of stand or stand - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 43
Figure 17. Removing the stand Steps 1. Locate the tab on the stand, and push a scribe into the tab to release the stand from the display-assembly base. 2. Lift the stand off the display-assembly base. Installing the stand Prerequisites If you are replacing a component, remove the existing component - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 44
After working inside your computer. Back cover Removing the back cover Prerequisites 1. Follow the procedure in Before working inside your computer. CAUTION: When servicing the computer, place it on an elevated, clean, and flat surface. Place the display flat on the surface with the stand over the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 45
About this task The following image indicates the location of the back cover and provides a visual representation of the removal procedure. Figure 20. Removing back cover Steps 1. Place your palm in the middle of the back cover, and then pry the back cover from the display-assembly base starting - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 46
Figure 21. Installing the back cover Steps Align the slots on the back cover with the slots on the computer, and press along the side to snap the back cover into place. Next steps 1. Follow the procedure in After working inside your computer. I/O cover Removing the I/O cover Prerequisites 1. Follow - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 47
Figure 22. Removing I/O cover Steps 1. Remove the five screws (M3x5) that secure the I/O cover to the display-assembly base. 2. Lift the I/O cover off the display-assembly base. Installing the I/O cover Prerequisites If you are replacing a component, remove the existing component before performing - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 48
Steps 1. Place the I/O cover on the display-assembly base. 2. Align the screw holes on the I/O cover with the screw holes on the display-assembly base. 3. Replace the two screws (M3x5) that secure the I/O cover to the display-assembly base and snap the I/O cover back into place. Next steps 1. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 49
2. Lift the stand hinges off the display-assembly base. Installing the stand hinges Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. NOTE: For replacement of stand or stand hinges, the replacement kit is shipped with both - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 50
Remove the back cover. 4. Remove the I/O cover. NOTE: The etchings on the system-board shield do not represent the components that are supported by this computer. About this task The following image indicates the location of the system-board shield and provides a visual representation of the removal - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 51
NOTE: The etchings on the system-board shield do not represent the components that are supported by this computer. About this task The following image indicates the location of the system-board shield and provides a visual representation of the installation procedure. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 52
the system-board shield. About this task NOTE: The M.2 card that is installed on your computer depends on the configuration ordered. The supported card configurations on the M.2 card slot are: ● M.2 2230 solid-state drive ● M.2 2280 solid-state drive NOTE: This procedure applies only to computers - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 53
Figure 29. Installing the M.2 2230 solid-state drive Steps 1. Ensure that the thermal pad covering the M.2 2230 slot on the system board is in place. 2. Align the notch on the solid-state drive with the tab on the M.2 card slot. 3. Slide the solid-state drive into the M.2 card slot on the system - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 54
Figure 30. Removing the memory module Steps 1. Carefully spread apart the securing-clips on each end of the memory-module slot until the memory module is released. 2. Slide and remove the memory module from the memory-module slot. NOTE: Repeat steps 1 and 2 if you want to remove the other memory - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 55
Figure 31. Installing the memory module Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place. NOTE: If you do not hear the click, remove the memory - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 56
Figure 32. Removing the wireless card Steps 1. Remove the screw (M2x3.5) that secures the wireless-card bracket to the wireless card. 2. Slide and lift the wireless-card bracket off the wireless card. 3. Disconnect the antenna cables from the wireless card. 4. Slide and remove the wireless card from - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 57
1. Connect the antenna cables to the wireless card. The following table provides the antenna-cable color scheme for the wireless card that is supported by your computer. Table 26. Antenna-cable color scheme Connectors on the wireless card Main (white triangle) Antenna-cable color White Auxiliary - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 58
Retractable-camera assembly Removing the retractable-camera assembly Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove the I/O cover. 5. Remove the system-board shield. About this task The following image indicates - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 59
About this task The following image indicates the location of the retractable-camera assembly and provides a visual representation of the installation procedure. Figure 35. Installing the camera Steps 1. Slide and place the retractable-camera assembly on the display-assembly base. 2. Replace the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 60
About this task The following image indicates the location of the fan and provides a visual representation of the removal procedure. Figure 36. Removing the fan Steps 1. Disconnect the fan cable from its connector (FAN1) on the system board. 2. Remove the fan cable from the routing post on the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 61
Figure 37. Installing the fan Steps 1. Align the screw holes on the fan with the screw holes on the display-assembly base. 2. Replace the three screws (M2x3.5) that secure the fan to the display-assembly base. 3. Route the fan cable through the routing post on the display-assembly base. 4. Connect - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 62
Removing the speakers Steps 1. Disconnect the speaker cable from its connector (SPK1) the system board. 2. Remove the speaker cable from the routing guides on the display-assembly base. 3. Lift the speakers along with the cable off the display-assembly base. Installing the speakers Prerequisites If - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 63
the alignment posts and rubber grommets, place the speakers on the slots on the display-assembly base. 2. Route the speaker cable through the routing guide on the display-assembly base. 3. Connect the speaker cable to its connector (SPK1) on the system board. Next steps 1. Install the system-board - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 64
Figure 40. Removing the coin-cell battery Steps 1. Press the metal tab to release the coin-cell battery from the coin-cell battery socket. 2. Lift the coin-cell battery from the coin-cell battery socket. Installing the coin-cell battery Prerequisites If you are replacing a component, remove the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 65
Figure 41. Installing the coin-cell battery Steps With the positive-side facing up, insert the coin-cell battery into the battery socket on the system board and snap the battery into place. Next steps 1. Install the system-board shield. 2. Install the I/O cover. 3. Install the back cover. 4. Install - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 66
on the configuration you ordered. Heat sink Removing the heat sink- UMA CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 67
the installation procedure. NOTE: If either the system board or the heat sink is replaced, use the thermal pad or paste provided in the service kit. The thermal pad or paste ensures that the thermal conductivity is achieved. About this task The following image indicates the location of the heat - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 68
in After working inside your computer. Removing the heat sink- discrete CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 69
the installation procedure. NOTE: If either the system board or the heat sink is replaced, use the thermal pad or paste provided in the service kit. The thermal pad or paste ensures that the thermal conductivity is achieved. About this task The following image indicates the location of the heat - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 70
inside your computer. Media-card reader Removing the media-card reader CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 71
from the media-card reader slot. Installing the media-card reader CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 72
-button board with USB Removing the power-button board with USB CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 73
power-button board off the display-assembly base. Installing the power-button board with USB CAUTION: The information in this section is intended for authorized service technicians only. Removing and installing Field Replaceable Units (FRUs) 73 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 74
Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the power-button board with USB and provides a visual representation of the installation procedure. Figure 49. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 75
Removing the system board CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 76
Figure 50. System-board connectors 1. Solid-state drive slot (M.2 PCIe SSD) 3. Camera-cable connector (WEBCAM) 5. Fan cable connector (FAN1) 7. Memory-module slots (DIMM2, DIMM1) 9. Microphone-module cable connector (DMIC1) 11. Wireless-card slot (M.2 WLAN) 13. Display-cable connector (LVDS) 2. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 77
Figure 51. Removing the system board Removing and installing Field Replaceable Units (FRUs) 77 - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 78
on the system board. NOTE: This cable is only available on computers that support the touch option. 2. Disconnect the camera cable from its connector (WEBCAM) CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 79
Figure 53. System-board connectors 1. Solid-state drive slot (M.2 PCIe SSD) 3. Camera-cable connector (WEBCAM) 5. Fan cable connector (FAN1) 7. Memory-module slots (DIMM2, DIMM1) 9. Microphone-module cable connector (DMIC1) 11. Wireless-card slot (M.2 WLAN) 13. Display-cable connector (LVDS) 2. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 80
Figure 54. Placing the system board in the chassis 80 Removing and installing Field Replaceable Units (FRUs) - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 81
system board. 13. Connect the touchscreen cable to its connector (TOUCH) on the system board. NOTE: This cable is only available on computers that support the touch option. Next steps 1. Install the integrated heat sink or, discrete heat sink, as applicable. NOTE: The system board can be removed and - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 82
the back cover. 8. Install the stand. 9. Follow the procedure in After working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 83
to the display-assembly base. 3. Remove the microphone cable from the routing guides on the display-assembly base. 4. Lift the microphone module off the display : The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 84
. 2. Replace the four screws (M2X3.5) that secure the microphone module to the display-assembly base. 3. Route the microphone cable through the routing guides on the display-assembly base. 4. Adhere the tape that secures the microphone cable to the display-assembly base. Next steps 1. Install the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 85
antennas CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside the antennas Steps 1. Remove the antenna cables from the routing guides on the display-assembly base. NOTE: Make a note of the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 86
The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a sides of the display-assembly base. 3. Route the antenna cables through the routing guides on the display-assembly base. Next steps 1. Install the power-button board with - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 87
working inside your computer. Display panel Removing the display panel CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 88
Figure 60. Removing the screws Figure 61. Removing the display panel 88 Removing and installing Field Replaceable Units (FRUs) - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 89
up from the display-assembly base. Installing the display panel CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 90
Figure 63. Replacing the screws Steps 1. Slide and insert the display panel into the slot on the display-assembly base. 2. Route the display-backlight cable, touchscreen cable, and display cable on the display panel through the slots on the display-assembly base. 3. Place the display-assembly base - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 91
Middle frame assembly Removing the middle-frame assembly CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the stand. 3. Remove the back cover. 4. Remove the I/O cover. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 92
Base panel ● Wireless antennas (2) Installing the middle-frame assembly CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 93
Figure 65. Installing the middle-frame assembly Steps Place the middle-frame assembly on a flat and clean surface and perform the steps in the Post-requisites to install the middle-frame assembly. NOTE: The middle-frame assembly consists of the following: ● Middle frame ● Base panel ● Wireless - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 94
chapter details the supported operating systems along with instructions on how to install the drivers. Operating system Your Inspiron 24 5430 All-in-One supports the following operating systems: ● Windows 11 Home ● Windows 11 Pro Drivers and downloads When troubleshooting, downloading, or installing - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 95
8 BIOS Setup CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup. Certain changes can make your computer work incorrectly. NOTE: Depending on the computer and its installed devices, the items that are listed in this section may or may not be displayed. - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 96
. Table 28. System setup options-Overview menu Overview Inspiron 24 5430 All-in-One BIOS Version Displays the BIOS version number. Service Tag Displays the Service Tag of the computer. Asset Tag Displays the Asset Tag of the computer. Manufacture Date Displays the manufacture date of the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 97
Table 28. System setup options-Overview menu (continued) Overview Memory Available Displays the total computer memory available. Memory Speed Displays the memory speed. Memory Channel Mode Displays single or dual channel mode. Memory Technology Displays the technology that is used for the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 98
enabled. USB Configuration Enable Rear USB Ports Enables the rear USB ports. By default, the Enable Rear USB Ports option is enabled. Enable Side Boot Support Enables the side USB ports. By default, the Enable Side USB Ports option is enabled. Enable USB Boot - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 99
Table 31. System setup options-Storage menu (continued) Storage SATA/NVMe Operation Sets the operating mode of the integrated SATA hard drive controller. By default, the RAID On option is selected. Storage Interface Port Enablement Displays the information of various onboard drives. Enables or - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 100
Enable or disable USB devices like a mouse or keyboard to wake the system from Standby, Hibernate, and Power Off. By default, the USB Wake Support option is disabled. AC Behavior AC Recover Set what the your system will do when power is restored after an unexpected loss of power. By - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 101
Table 35. System setup options-Security menu (continued) Security For additional security, Dell Technologies recommends keeping the SMM Security Mitigation option enabled unless you have a specific application which is not compatible. NOTE: This feature may cause compatibility issues or loss of - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 102
Table 36. System setup options-Passwords menu (continued) Passwords ● The administrator password can be used in place of the computer and/or internal hard drive passwords. ● When set, the administrator password must be provided during a firmware update. ● Clearing the administrator password also - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 103
Updates Enable UEFI Capsule Firmware Updates Enables or disables BIOS updates through UEFI capsule update packages. NOTE: Disabling this option blocks the BIOS updates from services such as Microsoft Windows Update and Linux Vendor Firmware - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 104
with the number of failures equal to or greater than the value specified by the Auto operating system Recovery Threshold setup option and local Service operating system does not boot or is not installed. By default, the BIOSConnect option is enabled. Dell Auto OS Recovery Threshold Allows you to - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 105
On Self-Test) load time. By default, the 0 seconds option is selected. Table 41. System setup options-Virtualization menu Virtualization Support Intel Virtualization Technology Enable Intel Virtualization Technology (VT) When enabled, the computer can run a Virtual Machine Monitor (VMM). By default - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 106
NOTE: This option is not available when the virtualization setting for IOMMU is disabled (VT-d/AMD Vi). By default, the Enable OS Kernel DMA Support option is enabled. NOTE: This option is provided only for compatibility purposes, since some older hardware is not DMA capable. Table 42. System setup - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 107
. 2. Click Product support. In the Search support box, enter the Service Tag of your computer, and then click Search. NOTE: If you do not have the Service Tag, use the SupportAssist feature to automatically identify your computer. You can also use the product ID or manually browse for your computer - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 108
. The BIOS Update Utility appears. 8. Follow the on-screen instructions to complete the BIOS update. Updating the BIOS in Linux and with Linux or Ubuntu, see the knowledge base article 000131486 at www.dell.com/support. Updating the BIOS from the One Time Boot menu Update your computer BIOS using - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 109
System and setup password Table 44. System and setup password Password type System password Setup password Description Password that you must enter to log in to your system. Password that you must enter to access and make changes to the BIOS settings of your computer. You can create a system - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 110
Diagnostics. Clearing BIOS (System Setup) and System passwords About this task To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell. NOTE: For information about how to reset Windows or application passwords, see the documentation accompanying - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 111
9 Troubleshooting Dell SupportAssist Pre-boot System Performance Check diagnostics About this you the tests are completed successfully. ● View error messages that inform you of problems encountered during testing. NOTE: Some tests for specific devices require user interaction. Always ensure - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 112
CPU failure ● Run the Dell Support Assist/Dell Diagnostics tool. ● If problem persists, replace the system board. problem persists, replace the system board. ● Flash latest BIOS version ● If problem persists, replace the system board. Replace the system board. 112 Troubleshooting - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 113
and the instructions are in the website Dell support. ● If problem persists, Guide at www.dell.com/serviceabilitytools. Click SupportAssist and then, click SupportAssist OS Recovery. Backup media and recovery options It is recommended to create a recovery drive to troubleshoot and fix problems - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 114
to Wi-Fi connectivity issues a Wi-Fi power cycle procedure may be performed. The following procedure provides the instructions on how to conduct a Wi-Fi power cycle: NOTE: Some Internet Service Providers (ISPs) provide a modem or router combo device. Steps 1. Turn off your computer. 2. Turn off the - Dell Inspiron 24 5430 All-in-One | Owners Manual - Page 115
your computer through videos, manuals, and documents. Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your Dell computer, enter the Service Tag or Express Service Code at www.dell.com/support. For more information about
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
 |
 |
Inspiron 24 5430 All-in-One
Owner's Manual
Regulatory Model: W29C
Regulatory Type: W29C001
January 2024
Rev. A00