Dell PowerConnect 3424P Command Line Interface (CLI) Guide (.htm)
Dell PowerConnect 3424P Manual
View all Dell PowerConnect 3424P manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerConnect 3424P manual content summary:
- Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 1
Dell™ PowerConnect™ 3400 Series CLI Reference Guide www.dell.com | support.dell.com - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 2
to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and PowerConnect are trademarks of Dell Inc. Other - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 3
Commands 29 Ethernet Configuration Commands 29 GVRP Commands 31 IGMP Snooping Commands 31 IP Addressing 32 LACP Commands 33 LLDP Commands 34 Line Commands 35 Management ACL Commands 35 PHY Diagnostics Commands 36 Port Channel Commands 36 Port Monitor Commands 36 Power-over-Ethernet - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 4
(SSH Public Key) Mode 60 UE (User EXEC) Mode 60 VC (VLAN Configuration) Mode 62 3 Using the CLI CLI Command Modes 63 Introduction 63 User EXEC Mode 64 Privileged EXEC Mode 65 Global Configuration Mode 66 Interface Configuration Mode and Specific Configuration Modes . . . . 66 4 Contents - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 5
68 Setup Wizard 69 Terminal Command Buffer 69 Negating the Effect of Commands 70 Command Completion 70 Keyboard Shortcuts 70 CLI Command Conventions 71 4 AAA Commands aaa authentication login 73 aaa authentication enable 74 login authentication 75 enable authentication 76 ip http - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 6
set enable-password active 89 show passwords configuration 89 show users login-history 91 show users accounts 92 5 ACL Commands mac access-list 95 deny (MAC 95 service-acl 96 show access-lists 97 show interfaces access-lists 97 6 Address Table Commands bridge address 99 bridge multicast - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 7
show bridge multicast address-table 112 show bridge multicast filtering 114 show ports security 115 show ports security addresses 116 7 Clock clock set 119 clock source 129 show clock 130 show sntp configuration 131 show sntp status 132 8 Configuration and Image Files copy 135 Contents 7 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 8
show running-config 144 show startup-config 145 show bootvar 146 9 DHCP Filtering ip dhcp filtering vlan 147 ip dhcp filtering trust 147 show ip dhcp filtering 148 10 Ethernet Configuration Commands interface ethernet 151 interface range ethernet 151 shutdown 152 description 153 speed 154 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 9
set interface active 159 show interfaces advertise 159 show interfaces configuration 162 show interfaces status 163 show interfaces description 165 show interfaces counters 166 port storm-control include-multicast 168 port storm-control broadcast enable 169 port storm-control broadcast rate - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 10
interface 186 show ip igmp snooping groups 187 13 IP Addressing Commands ip address 189 ip address dhcp 190 ip default-gateway 191 show ip interface 191 arp 192 arp timeout 193 clear arp-cache 194 show arp 194 ip domain-lookup 195 ip domain-name 196 ip name-server 196 ip host 197 clear - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 11
show lacp ethernet 203 show lacp port-channel 205 15 Line Commands line 207 speed 207 autobaud 208 reinit-delay 217 lldp tx-delay 218 lldp optional-tlv 219 lldp management-address 219 clear lldp rx 220 show lldp configuration 221 show lldp local 221 show lldp neighbors 222 Contents 11 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 12
233 19 Port Channel Commands interface port-channel 235 interface range port-channel 235 channel-group 236 show interfaces port-channel 237 20 Port Monitor Commands port monitor 239 port monitor vlan-tagging 240 show ports monitor 240 21 Power over Ethernet Commands power inline 243 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 13
power inline powered-device 244 power inline priority 244 power inline usage-threshold 245 power inline traps enable 246 show power inline 246 22 QoS Commands retransmit 261 radius-server source-ip 261 radius-server timeout 262 radius-server deadtime 263 show radius-servers 263 Contents - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 14
24 RMON Commands show rmon statistics 265 rmon collection history 267 show 279 25 SNMP Commands snmp-server community 281 snmp-server view 282 snmp-server group 284 snmp-server user 285 snmp-server engineID local 287 snmp-server enable traps 288 snmp-server filter 289 snmp-server host - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 15
show snmp views 297 show snmp groups 298 show snmp filters 300 show snmp users 301 26 Spanning-Tree Commands spanning-tree 303 spanning-tree mode 303 spanning- mst max-hops 313 spanning-tree mst port-priority 314 spanning-tree mst cost 314 spanning-tree mst configuration 315 Contents 15 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 16
-tree 320 spanning-tree guard root 335 27 SSH Commands ip ssh port 337 ip ssh server 337 crypto key generate dsa 338 crypto key generate rsa 339 ip ssh pubkey-auth 339 crypto key pubkey-chain ssh 340 user-key 341 key-string 342 show ip ssh 344 show crypto key mypubkey 345 show crypto - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 17
logging 358 show logging file 360 show syslog-servers 362 29 System Management ping 365 traceroute 367 telnet 369 resume 372 reload 373 hostname 374 stack master 374 stack reload 375 stack display-order 376 show stack 376 show users 378 show sessions 379 show system 380 Contents 17 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 18
id 382 service cpu-utilization 383 show cpu utilization 384 30 TACACS+ Commands tacacs-server host 385 tacacs-server key 386 tacacs-server timeout 387 tacacs-server source-ip 387 show tacacs 388 31 User Interface enable 391 disable 391 login 392 configure 393 exit (Configuration 393 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 19
disable 413 switchport general acceptable-frame-type tagged-only 413 switchport forbidden vlan 414 switchport customer vlan 415 ip internal-usage-vlan 415 mac-to-vlan 416 show vlan mac-to-vlan 417 show vlan 418 show vlan internal usage 419 show interfaces switchport 419 Contents 19 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 20
33 Web Server ip http server 425 ip http port 425 ip https server 426 ip https port 427 crypto certificate generate 427 crypto certificate request 428 crypto certificate import 430 ip https certificate 432 show crypto certificate mycertificate 432 show ip http 433 show ip https 434 34 802 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 21
show dot1x statistics 449 ADVANCED FEATURES 451 dot1x auth-not-req 451 dot1x multiple-hosts 452 dot1x single-host-violation 452 dot1x guest-vlan 453 dot1x guest-vlan enable 454 show dot1x advanced 455 Contents 21 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 22
22 Contents - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 23
You can access the CLI from a VT100 terminal connected to the console port of the device or through a Telnet connection from a remote host. The first time you use the CLI from the console a Setup Wizard is invoked. The Setup Wizard guides you in setting up a minimum configuration, so that the device - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 24
www.dell.com | support.dell.com Ethernet Configuration GVRP IGMP Snooping IP Addressing LACP Line LLDP Management ACL PHY Diagnostics Port Channel Port Monitor QoS RADIUS RMON SNMP Spanning Tree SSH Syslog Commands System Management TACACS User Interface VLAN Web Server 802.1x Configures all port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 25
Configuration passwords lockout Sets the number of failed login attempts before a user account is locked. Global Configuration aaa login-history file Enables writing to the login history file. Global Configuration set username active Reactivates a locked user account. Privileged EXEC DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 26
www.dell.com | support.dell.com set line active Reactivates a locked line. set enable-password active Reactivates a locked local password. show passwords configuration Displays information about password management. show users login-history Displays information about the login history of users - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 27
current dynamic addresses in locked ports. Privileged EXEC Interface Configuration Interface Configuration Interface Configuration Interface Configuration Privileged EXEC Privileged EXEC Privileged EXEC Privileged EXEC Privileged EXEC Privileged EXEC Privileged EXEC DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 28
poll sntp server show clock show sntp configuration show sntp status Description Manually sets the system clock. Configures an external time source for the system clock. Sets the time zone for display purposes. Configures the system to automatically switch to summer time (daylight saving time - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 29
EXEC Privileged EXEC Privileged EXEC DHCP Filtering Commands Command Group ip dhcp filtering vlan Description Enable filtering of DHCP requests on a VLAN. ip dhcp filtering trust show ip dhcp filtering Configure a port as trusted for DHCP filtering purposes. Display the DHCP filtering - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 30
www.dell.com | support.dell.com description duplex speed negotiation flowcontrol mdix back-pressure clear counters set interface active show interfaces advertise show interfaces configuration show interfaces status show interfaces description show interfaces counters port storm-control include- - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 31
snooping mrouter show ip igmp snooping interface Enables Internet Group Management Protocol (IGMP) snooping. Enables Internet Group Management Protocol (IGMP) snooping on a specific VLAN. Enables automatic learning of multicast router ports. Configures the host-time-out. Configures the mrouter-time - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 32
www.dell.com | support.dell.com show ip igmp snooping groups IP Addressing Displays multicast groups learned by IGMP snooping. User EXEC Command Group ip address ip address dhcp ip default-gateway show ip interface arp arp timeout clear arp-cache show arp ip domain-lookup ip domain-name ip name- - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 33
. show lacp ethernet show lacp port-channel Displays LACP information for Ethernet ports. Displays LACP information for a port-channel. Access Mode Global Configuration Interface Configuration Interface Configuration Privileged EXEC Privileged EXEC DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 34
the management address that would be advertised from an interface. Restarts the LLDP RX state machine and clears the neighbors table. Displays the Link Layer Discovery Protocol (LLDP) configuration. Displays the Link Layer Discovery Protocol (LLDP) information that is advertised from a specific port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 35
. Access Mode Global Configuration Line Configuration Line Configuration Line Configuration Line Configuration Line Configuration User EXEC User EXEC User EXEC Management ACL Commands Command Group management access-list permit (Management) Description Defines a management access-list, and - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 36
. Access Mode Privileged EXEC User EXEC User EXEC Privileged EXEC Port Channel Commands Command Group interface port-channel interface range portchannel channel-group show interfaces portchannel Description Enters the interface configuration mode of a specific port-channel. Enters the interface - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 37
each port trust state. Configures the default port CoS value. Displays all the maps for QoS. Access Mode Global Configuration User EXEC Global Configuration Global Configuration User EXEC Global Configuration Global Configuration Interface Configuration Interface Configuration User EXEC DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 38
IP address used for communication with RADIUS servers. Sets the interval for which a device waits for a server host to reply. Improves RADIUS response times when servers are unavailable. Displays the RADIUS server settings. Access Mode Global Configuration Global Configuration Global Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 39
send Simple Network Management Protocol traps when authentication failed. Sets up a system contact. Sets up the information on where the device is located. Sets SNMP MIB value by the CLI. Displays the SNMP status. Displays the local SNMP EngineID. Displays the configuration of SNMP views. Displays - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 40
spanning tree on a specific port. spanning-tree cost Configures the spanning tree path cost for a port. spanning-tree portpriority spanning-tree portfast Configures port priority. Enables PortFast mode. spanning-tree link-type Overrides the default link-type setting. spanning-tree pathcost - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 41
Configuration MST Configuration MST Configuration MST Configuration MST Configuration MST Configuration Privileged EXEC Interface Configuration SSH Commands Command Group ip ssh port ip ssh server crypto key generate dsa crypto key generate rsa ip ssh pubkey-auth crypto key pubkeychain ssh user - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 42
logging management access list events. Global Configuration show logging Displays the state of logging and the syslog messages Privileged EXEC stored in the internal buffer. show logging file Displays the state of logging and the syslog messages Privileged EXEC stored in the logging file. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 43
host that supports Telnet. Switches to User EXEC User EXEC User EXEC User EXEC Privileged EXEC Global Configuration Global Configuration Privileged EXEC Global Configuration User EXEC User EXEC User EXEC User EXEC User EXEC Global Configuration User EXEC Global Configuration Privileged EXEC DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 44
the source IP address that will be used for the communication with TACACS+ servers. Sets the timeout value. Displays configuration and statistics for a TACACS+ servers. Mode Global Configuration Global Configuration Global Configuration Global Configuration Privileged EXEC User Interface Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 45
-filtering disable Displays information about private VLANs. Adds or removes VLANs from a port in general mode. Defines the port as a member of the specified VLAN, and the VLAN ID is the "port default VLAN ID (PVID)". Adds or removes VLANs from a general port. Configures the PVID when the interface - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 46
tagged-only switchport forbidden vlan switchport customer vlan ip internal-usage-vlan mac-to-vlan show vlan mac-to-vlan show vlan show vlan internal usage show interfaces switchport Discards untagged frames at ingress. Forbids adding specific VLANs to a port. Sets the port's VLAN when the interface - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 47
port, that has the dot1x port-control interface configuration command set to auto. Access Mode Global Configuration Global Configuration Interface Configuration Interface Configuration Interface Configuration Privileged EXEC Interface Configuration Interface Configuration Interface Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 48
an 802.1xauthorized port, that has the dot1x port-control Interface Configuration mode command set to auto. Configures the action to be taken, when a station whose MAC address is not the supplicant MAC address, attempts to access the interface. Defines a guest VLAN. Enables unauthorized users on the - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 49
ARP cache Specifies the device asset-tag. Sets the address table aging time. Enables filtering of multicast addresses. Configures an external time source for the system clock Sets the time zone for display purposes Configures the system to automatically switch to summer time (daylight saving time - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 50
www.dell.com | support.dell.com enable password end file-system logging gvrp enable (Global) hostname interface ethernet interface port-channel interface range ethernet interface range port-channel interface range vlan interface vlan ip default-gateway ip domain-lookup ip domain-name ip host ip - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 51
relevant for tracking its password history. Sets the number of failed login attempts before a user account is locked. Sets the minimum required length for passwords in the local database. Adds a description of the powered device type attached to the interface. Configures the administrative mode of - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 52
up the information on where the device is located. Sets SNMP MIB value by the CLI. Enables the device to send Simple Network Management Protocol traps when authentication failed. Configures a new SNMP v3 user. Creates and modifies view entries. Grants authentication for received Simple Network Time - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 53
. Specifies the source IP address that will be used for the communication with TACACS+ servers. Sets the timeout value. Specifies a TACACS+ host. Establishes a username-based authentication system. Enters the VLAN database configuration mode. Maps CoS values to a specific egress queu IC (Interface - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 54
Enables or disables dynamic VLAN creation. ip address Sets an IP address ip address dhcp Acquires an IP address on an interface from the DHCP server. ip internal-usage-vlan Reserves a VLAN as the internal usage VLAN of an interface. lacp port-priority Configures the priority value for - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 55
secure addresses to a routed port. Enables broadcast storm control. Configures the maximum broadcast rate. Enables the device to count multicast packets. Associates the primary VLAN and community VLANs. Defines the isolated VLAN of the PVLAN. Defines the primary PVLAN. Configures the default port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 56
www.dell.com | support.dell.com spanning-tree link-type spanning-tree mst cost spanning-tree mst portpriority spanning-tree portfast spanning-tree port-priority speed switchport private-vlan Overrides the default link-type setting. Configures the path cost for multiple spanning tree (MST) - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 57
-to-address cache Deletes entries from the host name-to-address mapping received from Dynamic Host Configuration Protocol Manually sets the system clock. Enters the Global Configuration mode. Copies files from a source to a destination. Generates and displays certificate requests for HTTPS. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 58
-table count Displays the number of addresses present in all VLANs or at specific VLAN. show bridge multicast address-table Displays multicast MAC or IP address table information. show bridge multicast filtering Displays the multicast filtering configuration. show crypto key mypubkey Displays - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 59
interfaces description show interfaces port-channel show interfaces status show ip interface show ip ssh show logging show logging file show management accessclass show management access-list show passwords configuration show ports security show ports security addresses show ports storm-control show - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 60
www.dell.com | support.dell.com show snmp views show spanning-tree show startup-config show syslog-servers show tacacs show users accounts show users login-history show vlan internal usage show vlan mac-to-vlan show vlan private-vlan stack reload test copper-port tdr Displays the configuration of - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 61
multicast switch ports in the context of a specific VLAN. Displays multicast groups learned by IGMP snooping. Displays IGMP snooping configuration. . Displays system information. Displays the service id information. Displays information about the active users. Displays the system version information. - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 62
Group Management Protocol (IGMP) snooping on a specific VLAN. Configures the host-time-out. Configures the leave-time-out. Enables automatic learning of multicast router ports. Configures the mrouter-time-out. Adds MAC addresses to the MAC-to-VLAN database. Creates a VLAN. Enables unauthorized users - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 63
in using the CLI. CLI Command Modes Introduction To assist in configuring the device, the Command Line Interface (CLI) is divided into different command modes. Each command mode has its own set of specific commands. Entering a question mark "?" at the system prompt (console prompt) displays a list - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 64
a password is required. The Privileged EXEC mode gives access to commands that are restricted on User EXEC mode and provides access to the device Configuration mode. The Global Configuration mode manages the device configuration on a global level. The Interface Configuration mode configures specific - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 65
the angle bracket (>). Console> The default host name is Console unless it was changed using the hostname command in the Global Configuration mode. Privileged EXEC Mode Privileged access is password protected to prevent unauthorized use because, many of the privileged commands set operating system - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 66
Console(config)# exit Console# Interface Configuration Mode and Specific Configuration Modes Interface Configuration mode commands modify specific interface operations. The following are the Interface Configuration modes: • Line Interface - Contains commands to configure the management connections - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 67
based on MAC addresses. The mac access-list Global Configuration mode command is used to enter the MAC access-list configuration mode.. Starting the CLI The device can be managed over a direct connection to the device console port or via a Telnet connection. The device is managed by entering command - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 68
microsoft.com for information on Windows 2000 service packs. For more information, see Dell™ PowerConnect™ 3400 Series User's Guide. 2 Enter the following commands to begin the configuration procedure: Console> enable Console# configure Console(config)# 3 Configure the device and enter the necessary - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 69
Configuration mode has been accessed. • The commands contain no encrypted data, like encrypted passwords or keys. Encrypted data cannot be copied and pasted into the device. Setup Wizard The CLI supports a Setup Wizard. This is an easy-to-use user interface which quickly guides the user in setting - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 70
dell.com | support.dell.com There is a standard default number of commands that are stored in the buffer. The standard number of 10 commands can be increased to 216. By configuring the effect of a command or reset the configuration to the default value. This guide describes the negation effect for - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 71
the console. When a parameter is required to define a range of ports or parameters and all is an option, the default for the port-channel has the option of either entering a range of channels, or selecting all. When the command is entered without a parameter, it automatically defaults to all. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 72
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 72 Using the CLI - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 73
The local user database is checked. This has the same effect as the command aaa authentication login default local. NOTE: On the console, login succeeds without any authentication check if the authentication method is not defined. Command Mode Global Configuration mode DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 74
www.dell.com | support.dell.com User Guidelines • The default and optional list names user database. If there is no database, then no authentication is performed. Console(config)# aaa authentication login radius local none aaa authentication enable The aaa authentication enable Global Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 75
enable default enable. On the console, the enable password is used if it exists. If no password is set, the process still succeeds. This has the same effect as using the command aaa authentication enable default enable none. Command Mode Global Configuration mode User Guidelines • The default and - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 76
the default set with the command aaa authentication login. Command Mode Line Configuration mode User Guidelines • Changing login authentication from default to another value may disconnect the telnet session. Example The following example specifies the default authentication method for a console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 77
level from a console. Console(config)# line console Console(config-line)# enable authentication default ip http authentication The ip http authentication Global Configuration mode command specifies authentication methods for HTTP server users. To return to the default configuration, use the no - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 78
following example configures the HTTP authentication. Console(config)# ip http authentication radius local ip https authentication The ip https authentication Global Configuration mode command specifies authentication methods for HTTPS server users. To return to the default configuration, use the - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 79
show authentication methods Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the authentication configuration. Console# sh authentication methods - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 80
.dell.com | support.dell.com Line Console Telnet SSH Login Method List Default Default Default Enable Method List Default Default Default http https dot1x console# : Local : Local : password The password Line Configuration mode command specifies a password on a line. To remove the password - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 81
device configuration. Default Configuration No enable password is defined. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example sets local level 15 password secret to control access to privilege levels. Console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 82
www.dell.com | support.dell.com Default Configuration No user is defined. Command Mode Global Configuration mode User Guidelines • User account can be created without a password. Example The following example configures user bob with password lee and user level 15 to the system. Console(config)# - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 83
level - The level to which the password applies (Range: 1-15). Default Configuration No password expiration time. Command Mode Global Configuration mode User Guidelines • Relevant to local user passwords, line passwords, and enable passwords. • The password expiration date is calculated from the day - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 84
dell.com | support.dell.com Example The following example sets the expiration time of the level 15 enable password to 180 days. Console (config)# passwords aging enable-password 15 180 password-aging The password-aging Line Configuration mode command configures the expiration time of line passwords - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 85
3. Console(config)# passwords history 3 passwords history hold-time The passwords history hold-time Global Configuration mode command configures the number of days a password is relevant for tracking its password history. To return to the default configuration, use the no form of this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 86
www.dell.com | support.dell.com Syntax passwords history hold-time days no passwords hold-time • days-Number of days a password is relevant for tracking its password history (Range: 1-product specific). Default Configuration Not enabled. Command Mode Global Configuration mode User Guidelines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 87
set username active command. Example The following example configures the number of failed login attempts before a user account is locked to 3. Console(config)# passwords file Default Configuration Writing to the login history file is enabled. Command Mode Global Configuration mode User Guidelines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 88
www.dell.com | support.dell.com set username active The set username active Privileged EXEC mode command reactivates a locked user account. Syntax set username name active • name-Name of the user (Range: 1-20 characters). Default Configuration This command has no default configuration. Command Mode - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 89
password. Console# set enable-password 15 active show passwords configuration The show passwords configuration Privileged EXEC mode command displays information about password management. Syntax show passwords configuration Default Configuration This command has no default configuration. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 90
www.dell.com | support.dell.com Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information about password management in the local database. Console# show passwords configuration Minimal length: 8 History: 10 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 91
of a specific line password. show users login-history The show users login-history Privileged EXEC mode command displays information about the login history of users. Syntax show users login-history [username name] • name-Name of the user (Range: 1-20 characters). Default Configuration This command - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 92
mode command displays information about the local user database. Syntax show users accounts Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 93
Example The following example displays the local users configured with access to the system. Console# show users accounts Username Privilege -------Bob Admin --------1 15 Password Aging -------120 120 Password Expiry date ----------Jan 21 2005 Jan 21 2005 Lockout ------- The following table - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 94
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 94 AAA Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 95
Configuration The default for all ACLs is permit all. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example shows how to create a MAC ACL. Console(config)# mac access-list macl-1 Console(config-mac-al)# deny (MAC) The - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 96
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode MAC-Access List Configuration mode User Guidelines • MAC BPDU packets cannot be denied. • Each MAC address in the ACL is a ACE (Access Control Element) and can only be removed by deleting - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 97
to VLAN 2. Console(config)# interface vlan 2 Console(config-if)# service-acl input macl-1 show access-lists The show access-lists Privileged EXEC mode command displays access control lists (ACLs) defined on the device. Syntax show access-lists [name] • name -Name of the ACL. Default Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 98
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays an ACLs applied on the device interfaces: Console# show - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 99
command). This parameter is only available when the port is in the learning locked mode. Default Configuration No static addresses are defined. The default mode for an added address is permanent. Command Mode Interface Configuration (VLAN) mode User Guidelines • Using the no form of the command - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 100
Default Configuration Filtering multicast addresses is disabled. All multicast addresses are flooded to all ports. Command Mode Global Configuration mode User Guidelines • If multicast routers exist on the VLAN, do not change the unregistered multicast addresses state to drop on the switch ports - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 101
-channels with a comma and no spaces; a hyphen is used to designate a range of ports. Default Configuration No multicast addresses are defined. Command Mode Interface configuration (VLAN) mode User Guidelines • If the command is executed without add or remove, the command only registers the group - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 102
multicast forbidden address Interface Configuration (VLAN) mode command forbids adding a specific multicast address to specific ports. Use the no form of this command to return to the default configuration. Syntax bridge multicast forbidden address {mac-multicast-address | ip-multicast-address} {add - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 103
hyphen is used to designate a range of port-channels. Default Configuration This setting is disabled Command Mode Interface Configuration (VLAN) mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Address Table Commands 103 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 104
is used to designate a range of port-channels. Default Configuration This setting is disabled. Command Mode Interface Configuration (VLAN) mode User Guidelines • IGMP snooping dynamically discovers multicast router ports. When a multicast router port is discovered, all the multicast packets are - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 105
1/e1 with VLAN 2 is forbidden. Console(config)# interface vlan 2 Console(config-if)# bridge multicast forbidden forward-all add ethernet 1/e1 bridge aging-time The bridge aging-time Global Configuration mode command sets the address table aging time. To restore the default configuration, use the - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 106
) Default Configuration This setting is disabled. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. 802.1x multiple host mode must be enabled. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 106 Address Table - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 107
the current dynamic MAC addresses associated with the port. Learns up to the maximum addresses allowed on the port. Relearning and aging are enabled. Default Configuration This setting is disabled. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 108
default setting is 1 address. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines This command is only relevant in dynamic learning modes. Example In this example, the maximum number of addresses that are learned on port 1/e7 before it is locked is set to 20. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 109
a valid VLAN, such as VLAN 1. • interface - A valid Ethernet port. • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Address Table Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 110
a valid VLAN, such as VLAN 1. • interface - A valid Ethernet port. • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 110 Address Table - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 111
a valid VLAN, such as VLAN 1. • interface - A valid Ethernet port. • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 112
is unspecified, the default is mac. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines • A MAC address can be displayed in IP format only if it is in the range of 0100.5e00.0000- 0100.5e7f.ffff. DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 113
Example In this example, multicast MAC address and IP address table information is displayed. Console# show bridge multicast address-table Vlan ---1 19 19 MAC Address 01:00:5e:02:02:03 01:00:5e:02:02:08 00:00:5e:02:02:08 Type ------static static dynamic Ports ---------1/e1, 2/e2 1/e1-e8 1/e9- - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 114
has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example In this example, the multicast configuration for VLAN 1 is displayed. Console# show bridge multicast filtering 1 Filtering: Enabled VLAN: 1 Port ---1/e1 1/e2 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 115
number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example In this example, all classes of entries in the port-lock status are displayed: Console# show ports security Port ---1/e1 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 116
Ethernet port. • port-channel-number - A valid port-channel number Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 116 Address - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 117
1 1 10 50 128 In this example, dynamic addresses in currently locked port 1/e1 are displayed. Console# show ports security addresses ethernet 1/e1 Port ---1/e1 Status -------Disabled Learning -------Lock Current ------- Maximum ------1 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 118
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 118 Address Table Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 119
year (2000 - 2097). Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example sets the system time to 13:32:00 on the 7th March 2002. Console# clock set 13:32:00 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 120
www.dell.com | support.dell.com Syntax clock source {sntp} no clock source • sntp - SNTP servers Default Configuration No external clock source Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Examples The following example configures an external - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 121
when the time is manually set. Examples The following example sets the timezone to 6 hours difference from UTC. Console(config)# clock timezone -6 zone CST clock summer-time The clock summer-time Global Configuration mode command configures the system to automatically switch to summer time (daylight - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 122
. (Range: Up to 4 characters) Default Configuration Summer time is disabled. offset - Default is 60 minutes. acronym - If unspecified default to the timezone acronym. If the timezone has not been defined, the default is UTC. Command Mode Global Configuration mode User Guidelines • In both the date - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 123
- Key value (Range: 1-8 characters) Default Configuration No authentication key is defined. Command Mode Global Configuration mode User Guidelines • Multiple keys can be generated. Examples The following example defines the authentication key for SNTP. Console(config)# sntp authentication-key 8 md5 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 124
.dell.com | support.dell.com User Guidelines • The command is relevant for both unicast and broadcast. Examples The following example defines the authentication key for SNTP and grants authentication. Console(config)# sntp authentication-key 8 md5 ClkKey Console(config)# sntp trusted-key 8 Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 125
-86400) Default Configuration Polling interval is 1024 seconds. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Examples The following example sets the polling time for the Simple Network Time Protocol (SNTP) client to 120 seconds. Console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 126
www.dell.com | support.dell.com User Guidelines • Use the sntp client enable (Interface) Interface Configuration mode command to enable the SNTP client on a specific interface. Examples The following example enables the SNTP broadcast clients. Console(config)# sntp broadcast client enable sntp - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 127
sntp client enable no sntp client enable Default Configuration The SNTP client is disabled on an interface. Command Mode Interface configuration (Ethernet, port-channel, VLAN) mode User Guidelines • Use the sntp broadcast client enable Global Configuration mode command to enable broadcast clients - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 128
www.dell.com | support.dell.com User Guidelines • Use the sntp server Global Configuration mode command to define SNTP servers. Examples The following example enables the device to use the Simple Network Time Protocol (SNTP) to request and accept SNTP traffic from servers. Console(config)# sntp - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 129
- IP address of the server. • hostname - Hostname of the server. (Range: 1-158 characters) • poll - Enable polling. • keyid - Authentication key to use when sending packets to this peer. (Range:1-4294967295) Default Configuration No servers are defined. Command Mode Global Configuration mode User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 130
www.dell.com | support.dell.com show clock The show clock User EXEC mode command displays the time and date from the system clock. Syntax show clock [detail] • detail - Shows timezone and summertime configuration. Default Configuration This command has no default configuration. Command Mode User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 131
system clock. Console> show clock 15:29:03 PDT(UTC-7) Jun 17 2002 Time source is SNTP Console> show configuration of the Simple Network Time Protocol (SNTP). Syntax show sntp configuration Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 132
www.dell.com | support.dell.com User Guidelines There are no user guidelines for this command. Examples The following example displays the current SNTP configuration of the device. Console# show sntp configuration Polling interval: 7200 seconds MD5 Authentication keys: 8, 9 Authentication is - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 133
mode User Guidelines There are no user guidelines for this command. Examples The following example shows the status of the SNTP. Console# show Anycast server: Server Interface Status Last response Offset [mSec] --------- 176.1.11.8 VLAN 118 Up 9:53:21.789 PDT Feb 19 2002 7.19 Delay [mSec - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 134
www.dell.com | support.dell.com 134 Clock DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 135
by its IP address or hostname. Source for the file from a serial connection that uses the Xmodem protocol. Image file on one of the units. To copy from the master to all units, specify * in the member field. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Configuration and Image - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 136
configuration file.This is a user-defined name for up to four backup configuration files. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines • Up to five backup configuration files are supported destination exist. Specifically, you - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 137
commands were typed in the command-line interface (CLI). Thus, the resulting configuration file is a combination of the previous running configuration and the loaded configuration files with the loaded configuration file taking precedence. Copying a Configuration File from a Server to the Startup - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 138
specified without a prefix. Represents the startup configuration file. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines • *.sys, *.prv, image-1 and image-2 files cannot be deleted. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 139
Console# delete startup-config dir The dir Privileged EXEC mode command displays a list of files on a flash file system. Syntax dir Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 140
www.dell.com | support.dell.com Examples The following example displays files in the flash directory. Console# dir Directory of flash: File Name the file to be displayed. (Range: 1-160 characters) DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 140 Configuration and Image Files - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 141
startup configuration file. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines • Files are displayed in ASCII format, except for image files, which are displayed in hexadecimal format. • *.prv and *.sys files cannot be displayed. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 142
www.dell.com | support.dell.com Example The following example displays the contents of file configuration.bak. Console# more configuration.bak interface range ethernet 1/e(1-4) duplex half exit interface range ethernet 2/g(1-4) switchport mode general exit vlan database vlan 2 exit interface range - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 143
Configuration If the unit number is unspecified, the default setting is the master unit number. Command Mode Privileged EXEC mode User Guidelines • Use the show bootvar command to find out which image is the active image. Examples The following example loads system image 1 at device startup. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 144
command displays the factory default settings at the end of the running configuration file contents. Examples The following example displays the contents of the running configuration file. Device# show running-config software version 1.1 hostname device interface ethernet 1/e1 ip address 176.242.100 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 145
Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays the contents of the running configuration file. Console# show startup-config software version 1.1 hostname device interface ethernet 1/e1 ip address 176.242.100.100 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 146
dell.com | support.dell.com show bootvar The show bootvar Privileged EXEC mode command displays the active system image file that is loaded by the device at startup. Syntax show bootvar [unit unit] • unit - Specifies the unit number. Default Configuration This command has no default configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 147
requests on a VLAN. console(config)# ip dhcp filtering vlan 3 ip dhcp filtering trust Use the ip dhcp filtering trust interface configuration command to configure a port as trusted for DHCP filtering purposes. Use the no form of this command to return to the default setting. Syntax ip dhcp filtering - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 148
www.dell.com | support.dell.com Command Mode Interface configuration (Ethernet, Port-channel) User Guidelines • Configure as "trusted", ports that are connected to a DHCP server or to other switches or routers. • Configure as "untrusted", ports that are connected to DHCP clients. • The software - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 149
Example The following example displays the DHCP filtering configuration. Console# show ip dhcp filtering DHCP filtering is configured on following VLANs: 2,3 Interface Trusted 1/e1 yes 1/e2 yes DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY DHCP Filtering 149 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 150
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 150 DHCP Filtering - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 151
. (Full syntax: unit/port) Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables configuring Ethernet port 5/e18. Console(config)# interface ethernet - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 152
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines • Commands under the interface range context are executed independently on each active interface in the range. If the command returns an error on - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 153
: 1-64 characters) Default Configuration The interface does not have a description. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example adds a description to Ethernet port 1/e5. Console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 154
www.dell.com | support.dell.com speed The speed Interface Configuration (Ethernet, port-channel) mode command configures the speed of a given Ethernet interface when not using auto-negotiation. To restore the default configuration, use the no form of this command. Syntax speed {10 | 100 | 1000} no - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 155
half-duplex operation • full - Forces full-duplex operation Default Configuration The interface is set to full duplex. Command Mode Interface Configuration (Ethernet) mode User Guidelines • When configuring a particular duplex mode on the port operating at 10/100 Mbps, disable the auto-negotiation - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 156
is enabled. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines • If unspecified, the default setting is to enable all capabilities of the port. Example The following example enables auto-negotiation on Ethernet port 1/e5. Console(config)# interface ethernet 1/e5 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 157
auto} no mdix • on - Manual mdix • auto - Automatic mdi/mdix Default Configuration The default setting is on. Command Mode Interface Configuration (Ethernet) mode User Guidelines • Auto: All possibilities to connect a PC with cross or normal cables are supported and are automatically detected. • On - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 158
-pressure no back-pressure Default Configuration Back pressure is enabled. Command Mode Interface Configuration (Ethernet) mode User Guidelines • Back pressure cannot be configured on trunks. Example In the following example back pressure is enabled on port 1/e5. Console(config)# interface ethernet - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 159
no default configuration. Command Mode Privileged EXEC mode User Guidelines • This command is used to activate interfaces that were configured to be active, but were shutdown by the system for some reason (e.g., port security). Example The following example reactivates interface 1/e5. Console# set - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 160
www.dell.com | support.dell.com Syntax show interfaces advertise [ethernet interface | port-channel port-channel-number ] • interface - Valid Ethernet port. (Full syntax: unit/port) • port-channel-number - Valid port-channel number. Default Configuration This command has no default configuration. - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 161
Examples The following examples display autonegotiation information. Console# show interfaces advertise Port ---1/e1 1/e2 1/e3 1/e4 1/e5 1/e6 1/e7 1/e8 1/e9 1/e10 1/ Advertisement 100f, 100h, 10f, 10h DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Ethernet Configuration Commands 161 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 162
[ethernet interface | port-channel port-channel-number ] • interface - Valid Ethernet port. (Full syntax: unit/port) • port-channel-number - Valid port-channel number. Default Configuration This command has no default configuration. Command Modes Privileged EXEC mode User Guidelines • To view - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 163
- A valid Ethernet port. (Full syntax: unit/port) • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 164
www.dell.com | support.dell.com Example The following example displays the status of all configured interfaces: Console# show interfaces status Port Type ---1/e1 1/e2 1/e3 1/e4 1/e5 1/e6 1/e7 1/e8 1/e9 1/e10 1/e11 1/e12 1/e13 1/e14 1/e15 1/e16 1/e17 1/e18 1/e19 ----------100M-Copper 100M-Copper - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 165
port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Modes Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays descriptions of configured interfaces. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 166
- A valid port-channel number. Default Configuration This command has no default configuration. Command Modes Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays traffic seen by the physical interface: Console# show interfaces - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 167
port 1/e1. Console# show interfaces counters ethernet 1/e1 Port InOctets 1/e1 183892 InUcastPkts InMcastPkts 0 0 InBcastPkts ----------0 Port Pause Frames: 0 Transmitted Pause Frames: 0 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Ethernet Configuration Commands 167 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 168
www.dell.com | support.dell.com The following table describes the fields port storm-control include-multicast [unknown-unicast] no port storm-control include-multicast • unknown-unicast - Specifies also counting unknown unicast packets. Default Configuration Multicast packets are not counted. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 169
storm-control broadcast enable Default Configuration Broadcast storm control is disabled. Command Modes Interface Configuration (Ethernet) mode User Guidelines • Use the port storm-control broadcast rate Interface Configuration (Ethernet) mode command, to set the maximum allowable broadcast rate - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 170
www.dell.com | support.dell.com port storm-control broadcast rate The port storm-control broadcast rate Interface Configuration (Ethernet) mode command configures the maximum broadcast rate. To return to the default configuration, use the no form of this command. Syntax port storm-control broadcast - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 171
Ethernet port. (Full syntax: unit/port) Default Configuration This command has no default configuration. Command Modes Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the storm control configuration. Console# show ports storm - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 172
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 172 Ethernet Configuration Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 173
. Syntax gvrp enable no gvrp enable Default Configuration GVRP is globally disabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables GVRP globally on the device. Console(config)# gvrp enable gvrp enable - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 174
dell.com | support.dell.com Syntax gvrp enable no gvrp enable Default Configuration GVRP is disabled on all interfaces. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines • An access port does not dynamically join a VLAN because it is always a member in only one VLAN - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 175
. Example The following example sets the leave timer for Ethernet port 1/e6 to 900 milliseconds. Console(config)# interface ethernet 1/e6 Console(config-if)# garp timer leave 900 gvrp vlan-creation-forbid The gvrp vlan-creation-forbid Interface Configuration (Ethernet, port-channel) mode command - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 176
www.dell.com | support.dell.com Example The following example disables dynamic VLAN creation on Ethernet port 1/e6. console(config)# interface ethernet 1/e6 console(config-if)# gvrp vlan-creation-forbid gvrp registration-forbid The gvrp registration-forbid Interface Configuration (Ethernet, port- - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 177
port-channel-number] • interface - A valid Ethernet port. (Full syntax: unit/port) • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 178
www.dell.com | support.dell.com Example The following example displays GVRP configuration information: Console> show gvrp configuration GVRP Feature is currently enabled on the device. Port(s) Status -----2/e1 4/e4 ------Enabled Enabled Registration -----------Normal Normal Dynamic VLAN - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 179
port-channel-number] • interface - A valid Ethernet port. (Full syntax: unit/port) • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 180
www.dell.com | support.dell.com Example The following example displays GVRP statistical information. Console> show gvrp error-statistics GVRP Error Statistics: Legend: INVPROT : Invalid Protocol Id INVALEN : Invalid Attribute Length INVATYP : Invalid Attribute Type INVEVENT: Invalid Event - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 181
example enables IGMP snooping. Console(config)# ip igmp snooping ip igmp snooping (Interface) The ip igmp snooping Interface Configuration (VLAN) mode command enables Internet Group Management Protocol (IGMP) snooping on a specific VLAN. To disable IGMP snooping on a VLAN interface, use the no - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 182
www.dell.com | support.dell.com Default Configuration IGMP snooping is disabled. Command Mode Interface Configuration (VLAN) mode User Guidelines • IGMP snooping can only be enabled on static VLANs. It must not be enabled on Private VLANs or their community VLANs. Example The following example - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 183
-time-out. The ip igmp snooping mrouter-time-out Interface Configuration (VLAN) mode command is used for setting the aging-out time after multicast router ports are automatically learned. To return to the default configuration, use the no form of this command. DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 184
.dell.com | support.dell.com Syntax ip igmp snooping mrouter-time-out time-out no ip igmp snooping mrouter-time-out • time-out - Multicast router timeout in seconds (Range: 1 - 2147483647) Default Configuration The default value is 300 seconds. Command Mode Interface Configuration (VLAN) mode User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 185
just one host connected to a port. Example The following example configures the host leave-time-out to 60 seconds. Console(config)# interface vlan 2 Console(config-if)# ip igmp snooping leave-time-out 60 show ip igmp snooping mrouter The show ip igmp snooping mrouter User EXEC mode command displays - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 186
User EXEC mode command displays IGMP snooping configuration. Syntax show ip igmp snooping interface vlan-id • vlan-id - VLAN number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 187
by IGMP snooping. Syntax show ip igmp snooping groups [vlan vlan-id] [address ip-multicast-address] • vlan-id - VLAN number. • ip-multicast-address - IP multicast address. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines • To see the full - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 188
www.dell.com | support.dell.com Example The following example shows IGMP snooping information on multicast groups. Console> show ip igmp snooping groups Vlan ---1 19 IP Address 224-239.130|2.2.3 224-239.130|2.2.8 Querier -------Yes Yes Ports -----------1/e1, 2/e2 1/e9-e11 IGMP Reporters that - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 189
must be preceded by a forward slash (/). (Range: 8 -30) Default Configuration No IP address is defined for interfaces. Command Mode Interface Configuration (Ethernet, VLAN, port-channel) mode User Guidelines • An IP address cannot be configured for a range of interfaces (range context). Example The - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 190
default configuration. Command Mode Interface Configuration (Ethernet, VLAN, port-channel) mode User Guidelines • The ip address dhcp command allows any interface to dynamically learn its IP address by using the DHCP protocol. • Some DHCP servers require that the DHCPDISCOVER message have a specific - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 191
gateway 192.168.1.1. Console(config)# ip default-gateway 192.168.1.1 show ip interface The show ip interface User EXEC mode command displays the usability status of configured IP interfaces. Syntax show ip interface [ethernet interface-number | vlan vlan-id | port-channel port-channel number - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 192
no user guidelines for this command. Example The following example the displays the configured IP interfaces and their types. Console# show ip interface Gateway IP Address 10.7.1.1 Type -----Static Activity status Active IP address 10.7.1.192/24 10.7.2.192/24 Interface --------VLAN 1 VLAN - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 193
ARP cache. (Range: 1 40000000) Default Configuration The default timeout is 60000 seconds. Command Mode Global Configuration mode User Guidelines • It is recommended not to set the timeout value to less than 3600. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY IP Addressing Commands 193 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 194
displays entries in the ARP table. Syntax show arp Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 194 IP Addressing Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 195
Configuration mode User Guidelines There are no user guidelines for this command. Examples The following example enables IP Domain Naming System (DNS)-based host name-to-address translation. Console(config)# ip domain-lookup DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY IP Addressing - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 196
of host name-to-address entry. Static entries are read first, followed by DHCP entries and DNS-protocol entries. Examples The following example defines default domain name dell.com. Console(config)# ip domain-name dell.com ip name-server The ip name-server Global Configuration mode command defines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 197
IP address. Default Configuration No host is defined. Command Mode Global Configuration mode User Guidelines • Up to 64 host name-to address mapping entries are permitted in the host cache. Examples The following example defines a static host name-to-address mapping in the host cache. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 198
{name | *} • name - Specifies the host entry to be removed. (Range: 1-158 characters) • * - Removes all entries. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 198 IP Addressing Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 199
host information. Console# show hosts Host name: Device Default domain is gm.com, sales.gm.com, usa.sales.gm.com(DHCP) Name/address lookup is enabled Name servers (Preference order): 176.16.1.18 176.16.1.19 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY IP Addressing Commands 199 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 200
www.dell.com | support.dell.com Configured host name-to-address mapping: Host Addresses ---- --------- accounting.gm.com 176.16.8.8 176.16.8.9 (DHCP) Cache: Host ---www.stanford.edu TTL(Hours) Total Elapsed Type 72 3 IP Addresses --------171.64.14.203 DELL CONFIDENTIAL - - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 201
- 65535) Default Configuration The default system priority is 1. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example configures the system priority to 120. Console(config)# lacp system-priority 120 lacp port-priority The - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 202
www.dell.com | support.dell.com Default Configuration The default port priority is 1. Command Mode Interface Configuration (Ethernet) mode User Guidelines There are no user guidelines for this command. Example The following example defines the priority of Ethernet port 1/e6 as 247. Console(config)# - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 203
protocol-state information. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example display LACP information for Ethernet port 1/e1. Console# show lacp ethernet - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 204
www.dell.com | support.dell.com port Admin timeout: port Oper timeout: LACP Activity: Aggregation: synchronization: collecting: distributing: expired: Partner system priority: system mac addr: port Admin key: port Oper key: port Oper number: port Admin priority: port Oper priority: port Oper - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 205
timer: current while timer: wait while timer: Port Disabled State Detached State No Periodic State FALSE TRUE port-channel. Syntax show lacp port-channel [port_channel_number] • port_channel_number - Valid port-channel number. Default Configuration This command has no default configuration. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 206
www.dell.com | support.dell.com Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays LACP information about port-channel 1. Console# show lacp port-channel 1 Port-Channel 1: Port Type 1000 Ethernet Actor - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 207
device as a virtual terminal for remote console access. Console(config)# line telnet Console(config-line)# speed The speed Line Configuration mode command sets the line baud rate. To return to the default configuration, use the no form of the command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 208
www.dell.com | support.dell.com Syntax speed bps no speed • bps-Baud rate in bits per second (bps). Possible values are 2400, 9600, 19200, 38400, 57600 and 115200. Default Configuration The default speed is 9600 bps. Command Mode Line Configuration (console) mode User Guidelines • This command is - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 209
Examples The following example enables autobaud. Console(config)# line console Console(config-line)# autobaud exec-timeout The exec-timeout Line Configuration mode command sets the interval that the system waits until user input is detected. To return to the default configuration, use the no form of - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 210
history function for telnet. Console(config)# line telnet Console(config-line)# history history size The history size Line Configuration mode command configures the command history buffer size for a particular line. To reset the command history buffer size to the default configuration, use the no - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 211
the history line configuration command. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example disables the command history function for the current terminal session. Console# no terminal history DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 212
www.dell.com | support.dell.com terminal history size The terminal history size User EXEC command configures the command history buffer size for the current terminal session. To reset the command history buffer size to the default setting, use the no form of this command. Syntax terminal history - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 213
If the line is not specified, the default value is console. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays the line configuration. Console> show line Console configuration: Interactive timeout: Disabled History: 10 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 214
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 214 Line Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 215
enable no lldp enable Default Configuration The command is enabled. Command Mode Global configuration User Guidlines There are console (config)# lldp enable lldp enable (interface) To enable Link Layer Discovery Protocol (LLDP) on an interface, use the lldp enable command in interface configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 216
www.dell.com | support.dell.com Command Modes Interface configuration (Ethernet) User Guidelines • LLDP manages LAG ports individually. LLDP sends separate advertisements on each port in a LAG. LLDP data received through LAG ports is stored individually per port. • LLDP operation on a port is not - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 217
Discovery Protocol (LLDP) updates. Console (config) # lldp hold-multiplier 6 lldp reinit-delay To specify the minimum time an LLDP port will wait before reinitializing LLDP transmission, use the lldp reinit-delay command in global configuration mode. To revert to the default setting, use the no form - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 218
seconds). Default Configuraiton The default value is 2 seconds. Command Modes Global configuration User Guidelines There are no user guidelines for this command. Examples The following example pecifies the minimum time an LLDP port will wait before reinitializing LLDP transmission. Console (config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 219
the basic set should be transmitted. Console(config)# interface ethernet g5 Console(config-if)# lldp optional-tlv sys-name lldp management-address To specify the management address that would be advertised from an interface, use the lldp management-address command in interface configuration mode. To - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 220
www.dell.com | support.dell.com Syntax lldp management-address ip-address no management-address ip • ip-address - Specifies the management address to advertise. Default Configuration No IP address is advertised. Command Modes Interface configuration (Ethernet) User Guidelines • Each port can - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 221
port Command Modes Privileged EXEC User Guidelines There are no user guidelines for this command. Example The following example displays the Link Layer Discovery Protocol (LLDP) configuration. Switch# show lldp configuration is advertised from a specific port, use the show lldp local command in - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 222
www.dell.com | support.dell.com Command Modes Privileged EXEC User Guidelines There are no user guidelines for this command. Example The following example displays the Link Layer Discovery Protocol (LLDP) information that is advertised from a specific port. Switch# show lldp local ethernet g1 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 223
Capabilities Name B ts-7800-2 B ts-7800-2 B, R ts-7900-1 W ts-7900-2 Switch# show lldp neighbors ethernet g1 Device ID: 0060.704C.73FE Port ID: 1 Hold Time: 117 Capabilities: B System Name: ts-7800-2 System description: Port description: Management address: 172.16.1.1 LLDP Commands 223 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 224
www.dell.com | support.dell.com 224 LLDP Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 225
cannot be updated or removed. • Management ACL requires a valid management interface, which is a port, VLAN, or port channel with an IP address or console interface. Management ACL only restricts access to the device for management configuration or viewing. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 226
exit Console(config)# management access-class mlist permit (Management) The permit Management Access-List Configuration mode command defines a permit rule. Syntax permit [ethernet interface-number | vlan vlan-id | port-channel port-channel-number] [service service] permit ip-source ip-address [mask - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 227
rule is defined, the default is set to deny. Command Mode Management Access-list Configuration mode User Guidelines • Rules with Ethernet, VLAN and port-channel parameters are valid only if an IP address is defined on the appropriate interface. • The system supports up to 128 management access rules - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 228
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Management Access-list Configuration mode User Guidelines • Rules with Ethernet, VLAN and port-channel parameters are valid only if an IP address is defined on the appropriate interface. • - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 229
- 32 characters) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the mlist management access list. Console# show management access-list mlist mlist - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 230
.com | support.dell.com show management access-class The show management access-class Privileged EXEC mode command displays the active management access list. Syntax show management access-class Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 231
of a copper cable attached to a port. Syntax test copper-port tdr interface • interface - A valid Ethernet port. (Full syntax: unit/port) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines • The port to be tested should be shut down - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 232
www.dell.com | support.dell.com show copper-ports tdr [interface] • interface - A valid Ethernet port. (Full syntax: unit/port) Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines • The maximum length of the cable for the TDR test is 120 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 233
- A valid Ethernet port. (Full syntax: unit/port) • detailed - Detailed diagnostics. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines To test optical transceivers, ensure a fiber link is present. DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 234
www.dell.com | support.dell.com Examples The following examples display the optical transceiver diagnostics. Console# show fiber-ports optical-transceiver Port ---1/g1 1/g2 1/g3 Temp ---W OK Copper Voltage ------OK OK Current ------E OK Power Output Input ------ ----- OK OK OK OK TX - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 235
enters the interface configuration mode to configure a specific port-channel. Syntax interface port-channel port-channel-number • port-channel-number - A valid port-channel number. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 236
www.dell.com | support.dell.com Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines • Commands under the interface range context are executed independently on each interface in the range. Example The following example groups port- - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 237
- Valid port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information on all port-channels. Console# show interfaces port-channel - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 238
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 238 Port Channel Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 239
port is not a member of a VLAN, except for the default VLAN (will automatically be removed from the default VLAN). • The following restrictions apply to ports configured to be source ports: • The port cannot be already configured as a destination port. • Up to 8 source ports can be configured. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 240
interface ethernet 1/e9 Console (config-if)# port monitor vlan-tagging show ports monitor The show ports monitor User EXEC mode command displays the port monitoring status. Syntax show ports monitor Default Configuration This command has no default configuration. DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 241
no user guidelines for this command. Example The following example shows how the port monitoring status is displayed. Console> show ports monitor Source Port Destination Port Type Status VLAN Tagging 1/e1 1/e8 RX,TX Active No 1/e2 1/e8 RX,TX Active No 1/e18 1/e8 RX Active No DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 242
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 242 Port Monitor Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 243
the device. Default Configuration The device discovery protocol is enabled. Command Mode Interface Configuration (Ethernet) mode User Guidelines There are no user guidelines for this command. Example The following example enables powered device discovery protocol on port 1/e1, so that power will be - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 244
has no default configuration. Command Mode Interface Configuration (Ethernet) mode User Guidelines There are no user guidelines for this command. Example The following example configures a description to an IP-phone to a powered device connected to Ethernet interface 1/e1. Console(config)# interface - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 245
Default Configuration The default setting is low priority. Command Mode Interface Configuration (Ethernet) mode User Guidelines • An unlimited number of ports can be configured as critical, high or low. • As power becomes unavailable, critical and high ports continue to receive power at the expense - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 246
is exceeded. Console(config)# power inline traps enable show power inline The show power inline User EXEC mode command displays the information about inline power. Syntax show power inline [ethernet interface] • interface - Valid Ethernet port. (Full syntax: unit/port) Default Configuration This - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 247
Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays information about inline power. Console> show power inline Power: On Nominal Power: 150 Watt Consumed Power: 120 Watts (80%) Usage Threshold: 95% Traps: Enabled Port ---1/e1 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 248
www.dell.com | support.dell.com Console> show power inline ethernet 1/e1 Port ---1/e1 Powered Device State Priority Status Classification [w] IP Phone Model A Auto High On 0.44 - 12.95 Overload Counter: 1 Short Counter: 0 Denied Counter: 0 Absent Counter: 0 Invalid Signature Counter: 0 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 249
Counter Short Counter Denied Counter Absent Counter Invalid Signature Counter Describes the inline power operational status of the port. Can be: On, Off, Test-Fail, Testing, Searching or Fault. The power consumption range of the powered device. Can be: 0.44 - 12.95, 0.44 - 3.84, 3.84 - 6.49 or 6.49 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 250
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 250 Power over Ethernet Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 251
enables QoS on the device. Console(config)# qos show qos The show qos User EXEC mode command displays quality of service (QoS) for the device. Syntax show qos Default Configuration This command has no default configuration. Command Mode User EXEC mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 252
is 4, weights are defined as 1, 2, 4 and 8. • Port priority queues are used for internal purposes, such as stacking. Example The following example configures the number of expedite queues as 0. Console(config)# priority-queue out num-of-queues 0 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 253
Ethernet port number. • vlan-id- Valid VLAN ID. • number - Valid port-channel number. • queuing - Indicates the queue strategy (WRR or EF), the weight for WRR queues, the CoS to queue map and the EF priority. Default Configuration There is no default configuration for this command. Command Mode User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 254
www.dell.com | support.dell.com Cos-queue map: cos qid 0 2 1 1 2 1 3 2 4 3 5 3 6 4 7 4 wrr-queue cos-map The wrr-queue cos-map Global Configuration mode command maps Class of Service (CoS) values to a specific egress queue. To return to the default configuration, use the no form - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 255
following table describes the default map. DSCP value Queue-ID 0-15 16-39 40-63 1 2 3 Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example maps DSCP values 33, 40 and 41 to queue 1. Console(config)# qos map dscp - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 256
packet DSCP values. Default Configuration CoS is the default trust mode. Command Mode Global Configuration mode User Guidelines • Packets entering a quality of service (QoS) domain are classified at the edge of the QoS domain. When packets are classified at the edge, the switch port within the QoS - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 257
is used to assign a CoS value to all untagged packets entering the port. Example The following example configures port 1/e15 default CoS value to 3. Console(config)# interface ethernet 1/e15 Console(config-if) qos cos 3 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY QoS Commands 257 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 258
- Indicates the DSCP to queue map. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the DSCP port-queue map. Console> show qos map Dscp-queue map: d1 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 259
-server host The radius-server host Global Configuration mode command specifies a RADIUS server host. To delete the specified RADIUS host, use the no form of this command. Syntax radius-server host {ip-address | hostname} [auth-port auth-port-number] [timeout timeout] [retransmit retries] [deadtime - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 260
server host with IP address 192.168.10.1, authentication request port number 20 and a 20-second timeout period. Console(config)# radius-server host 192.168.10.1 auth-port 20 timeout 20 radius-server key The radius-server key Global Configuration mode command sets the authentication and encryption - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 261
. console(config)# radius-server retransmit 5 radius-server source-ip The radius-server source-ip Global Configuration mode command specifies the source IP address used for communication with RADIUS servers. To return to the default configuration, use the no form of this command. DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 262
www.dell.com | support.dell.com Syntax radius-server source-ip source no radius-source-ip source • source - Specifies a valid source IP address. Default Configuration The source IP address is the IP address of the outgoing IP interface. Command Mode Global Configuration mode User Guidelines There - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 263
by transaction requests. (Range: 0 - 2000) Default Configuration The deadtime setting is 0. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example sets the deadtime to 10 minutes. Console(config)# radius-server deadtime 10 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 264
www.dell.com | support.dell.com Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays RADIUS server settings. Console# show radius-servers IP address Port Auth 172.16.1.1 1645 172.16.1.2 1645 TimeOut ------ - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 265
- Valid port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays RMON Ethernet statistics for Ethernet port 1/e1. Console> show rmon - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 266
www.dell.com | support.dell.com The following table describes significant fields shown above: Field received. Broadcast The total number of good packets received and directed to the broadcast address. This does not include multicast packets. Multicast The total number of good packets received - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 267
3600) Default Configuration RMON statistics group owner name is an empty string. Number of buckets specified for the RMON collection history statistics group is 50. Number of seconds in each polling cycle is 1800. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 268
unit/port) • port-channel-number - Valid port-channel number. Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays all RMON history group statistics. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 269
has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Examples The following examples displays RMON Ethernet history statistics for index 1. Console> show rmon history 1 throughput Sample Set: 1 Owner: CLI Interface: 1/e1 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 270
dell.com | support.dell.com Console> show rmon history 1 errors Sample Set: 1 Owner: Me Interface: 1/e1 Interval: 1800 Requested samples: 50 Granted samples: 50 Maximum table size: 500 (800 after reset to the broadcast address. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 271
were directed to a multicast address. This number does not include packets addressed to the broadcast address. The best estimate of the The rmon alarm Global Configuration mode command configures alarm conditions. To remove an alarm, use the no form of this command. DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 272
dell.com | support.dell be sent when this entry is first set to valid. Possible values are rising, rising Default Configuration The type is absolute. The startup direction is rising-falling. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 273
index - 20 Console(config)# rmon alarm 1000 dell 360000 1000000 1000000 10 20 show rmon alarm-table The show rmon alarm-table User EXEC mode command displays the alarms table. Syntax show rmon alarm-table Default Configuration This command has no default configuration. Command Mode User EXEC mode - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 274
rmon alarm number • number - Specifies the alarm index. (Range: 1 - 65535) Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 274 RMON - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 275
displays RMON 1 alarms. Console> show rmon alarm 1 Alarm 1 ------- OID: 1.3.6.1.2.1.2.2.1.10.1 Last sample Value: 878128 Interval: 30 Sample Type: delta Startup Alarm: rising Rising Threshold: 8700000 Falling Threshold: 78 Rising Event: 1 Falling Event: 1 Owner: CLI The following table - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 276
characters) • name - Specifies the name of the person who configured this event. If unspecified, the name is an empty string. Default Configuration This command has no default configuration. Command Mode Global Configuration mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 276 RMON - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 277
. Syntax show rmon events Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the RMON event table. Console> show rmon events Index ----1 2 Description - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 278
rmon log [event] • event - Specifies the event index. (Range: 0 - 65535) Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 278 RMON - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 279
default configuration, use the no form of this command. Syntax rmon table-size {history entries | log entries} no rmon table-size {history | log} • history entries - Maximum number of history table entries. (Range: 20 -270) • log entries - Maximum number of log table entries. (Range: 20-100) DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 280
www.dell.com | support.dell.com Default Configuration History table size is 270. Log table size is 200. Command Mode Global Configuration mode User Guidelines • The configured table size takes effect after the device is rebooted. Example The following example configures the maximum RMON history - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 281
string that acts like a password and permits access to the SNMP protocol. (Range: 1-20 characters) • ro-Indicates read-only access (default). • rw-Indicates read-write access. • su-Indicates SNMP administrator access. • ip-address-Specifies the IP address of the management station. • group-name - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 282
www.dell.com | support.dell.com - An internal security name is generated. - The internal IP address 192.168.1.20. Console(config)# snmp-server community public su 192.168.1.20 snmp-server view The snmp-server view Global Configuration mode command creates or updates a Simple Network Management - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 283
Default Configuration No view entry exists. Command Mode Global Configuration mode User Guidelines • This command can be entered multiple times for the same view record. • The number of views is limited to 64 including pre-configured views. • No check is made to determine that a MIB node corresponds - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 284
snmp-server view user-view system included Console(config)# snmp-server view user-view system.7 excluded Console(config)# snmp-server view user-view ifEntry.*.1 included snmp-server group The snmp-server group Global Configuration mode command configures a new Simple Management Protocol (SNMP) group - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 285
level and read access rights to a view called user-view. Console(config)# snmp-server group user-group v3 priv read user-view snmp-server user The snmp-server user Global Configuration mode command configures a new SNMP Version 3 user. To remove a user, use the no form of this command. Syntax - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 286
remote engineid designates the remote management station and should be defined to enable the device to receive informs. Examples The following example configures an SNMPv3 user John in group user-group. Console(config)# snmp-server user John user-group DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 287
674. • Fifth octet - set to 3 to indicate the MAC address that follows. • Last 6 octets - MAC address of the device. Command Mode Global Configuration mode User Guidelines • To use SNMPv3, you have to specify an engine ID for the device. You can specify your own ID or use a default string that is - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 288
-server enable traps Default Configuration SNMP traps are enabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Examples The following example enables SNMP traps. Console(config)# snmp-server enable traps DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 289
Default Configuration No filter entry exists. Command Mode Global Configuration mode User Console(config)# snmp-server filter filter-name system included Console(config)# snmp-server filter filter-name system.7 excluded Console(config)# snmp-server filter filter-name ifEntry.*.1 included DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 290
.dell.com | support.dell.com snmp-server host The snmp-server host Global Configuration mode command specifies the recipient of Simple Network Management Protocol Version 1 or Version 2 notifications. To remove the specified host, use the no form of this command. Syntax snmp-server host {ip-address - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 291
Global Configuration mode command specifies the recipient of Simple Network Management Protocol Version 3 notifications. To remove the specified host, use the no form of this command. Syntax snmp-server v3-host {ip-address | hostname} username [traps | informs] {noauth | auth | priv} [udp-port port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 292
snmp-server trap authentication no snmp-server trap authentication Default Configuration SNMP failed authentication traps are enabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 292 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 293
has no default configuration. Command Mode Global Configuration mode User Guidelines • Do not include spaces in the text string or place text that includes spaces inside quotation marks. Example The following example configures the system contact point called Dell_Technical_Support. console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 294
default configuration. Command Mode Global Configuration mode User Guidelines • Although the CLI can set any required configuration, there might be a situation where a SNMP user sets a MIB variable that does not have an equivalent command. In order to generate configuration files that support those - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 295
displays the SNMP communications status. Console# show snmp Community- Community- String Access public private private read only read write su View name IP address --------- ------- user-view All Default 172.16.1.1 DefaultSuper 172.17.1.1 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 296
support.dell.com Community-string public Group name ---------user-group IP address ---------all Traps are enabled. Authentication trap is enabled. Version 1,2 notifications Target Address Type Community 192.122.173.42 192.122.173.42 Trap public Inform public Version ------2 2 UDP Port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 297
Network Management Protocol (SNMP) engine. Syntax show snmp engineID Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the SNMP engine ID. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 298
www.dell.com | support.dell.com Example The following example displays the configuration of views. Console# show snmp views Name OID Tree Type user-view 1.3.6.1.2.1.1 Included user-view 1.3.6.1.2.1.1.7 Excluded user-view 1.3.6.1.2.1.2.2.1.*.1 Included show snmp groups The show snmp - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 299
following example displays the configuration of views. Console# show snmp groups Name Security Views Model Level Read Write Notify user-group V3 priv Default "" "" managers-group V3 priv Default Default "" managers-group V3 priv Default "" "" The following table describes - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 300
This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the configuration of filters. Console# show snmp filters Name ----------user-filter user-filter user-filter OID Tree - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 301
of the user. (Range: 1-30) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the configuration of users. Console# show snmp users Name -----John - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 302
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 302 SNMP Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 303
Default Configuration Spanning-tree is enabled. Command Modes Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables spanning-tree functionality. Console is enabled. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 304
www.dell.com | support.dell.com Default Configuration STP is enabled. Command Modes Global Configuration mode User Guidelines • In RSTP mode, the device uses STP when the neighbor device uses STP. • In MSTP mode, the device uses RSTP when the neighbor device - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 305
-tree hello-time • seconds - Time in seconds. (Range: 1 - 10) Default Configuration The default hello time for IEEE Spanning Tree Protocol (STP) is 2 seconds. Command Modes Global Configuration mode User Guidelines • When configuring the hello time, the following relationship should be kept: - Max - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 306
www.dell.com | support.dell.com Default Configuration The default maximum age for IEEE Spanning Tree Protocol (STP) is 20 seconds. Command Modes Global Configuration mode User Guidelines • When configuring the maximum age, the following relationships should be kept: - 2*(Forward-Time - 1) >= Max- - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 307
specific port. To enable spanning tree on a port, use the no form of this command. Syntax spanning-tree disable no spanning-tree disable Default Configuration Spanning tree is enabled on all ports. Command Modes Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 308
www.dell.com | support.dell.com Default Configuration Default path cost is determined by port speed and path cost method (long or short) as shown below: Interface Port-channel Gigabit Ethernet (1000 Mbps) Fast Ethernet (100 Mbps) Ethernet (10 Mbps) Long 20,000 20,000 200,000 2,000,000 Short 4 4 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 309
Default Configuration PortFast mode is disabled. Command Modes Interface Configuration (Ethernet, port-channel) mode User Guidelines • This feature should be used only with interfaces connected port 1/e15. Console(config)# interface ethernet 1/e15 Console(config-if)# spanning-tree portfast DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 310
www.dell.com | support.dell.com spanning-tree link-type The spanning-tree link-type Interface Configuration mode command overrides the default linktype setting determined by the duplex mode of the port and enables Rapid Spanning Tree Protocol (RSTP) transitions to the forwarding state. To return to - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 311
The default setting is flooding. Command Modes Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example defines BPDU packet flooding when the spanning-tree is disabled on an interface. Console(config)# spanning-tree bpdu flooding DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 312
the user to set the switches back to RSTP mode without rebooting the device. Syntax clear spanning-tree detected-protocols [ethernet interface | port-channel port-channelnumber] • interface - A valid Ethernet port. • port-channel-number - A valid port-channel number. Default Configuration This - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 313
Configuration The default number of hops is 20. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example configures the maximum number of hops that a packet travels in an MST region before it is discarded to 10. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 314
www.dell.com | support.dell.com spanning-tree mst port-priority The spanning-tree mst port-priority Interface Configuration mode command configures port priority for the specified MST instance. To return to the default configuration, use the no form of this command. Syntax spanning-tree mst - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 315
. Syntax spanning-tree mst configuration Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines All devices in an MST region must have the same VLAN mapping, configuration revision number and name. DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 316
www.dell.com | support.dell.com Example The following example configures an MST region. Console(config)# spanning-tree mst configuration Console(config-mst) # instance 1 add vlan 10-20 Console(config-mst) # name region1 Console(config-mst) # revision 1 instance (mst) The instance MST Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 317
to the default setting, use the no form of this command. Syntax name string no name • string-MST configuration name. Case-sensitive (Range: 1-32 characters). Default Configuration The default name is a bridge ID. Command Mode MST Configuration mode User Guidelines There are no user guidelines for - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 318
www.dell.com | support.dell.com User Guidelines There are no user guidelines for this command. Example The following example sets the configuration revision to 1. Console(config)# spanning-tree mst configuration Console(config-mst)# revision 1 show (mst) The show MST Configuration mode command - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 319
no default configuration. Command Mode MST Configuration mode User Guidelines There are no user guidelines for this command. Example The following example exits the MST configuration mode and saves changes. Console(config)# spanning-tree mst configuration Console(config-mst)# exit DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 320
www.dell.com | support.dell.com abort (mst) The abort MST Configuration mode command exits the MST configuration mode without applying the configuration changes. Syntax abort Default Configuration This command has no default configuration. Command Mode MST Configuration mode User Guidelines There - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 321
configuration. Command Modes Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays spanning-tree information. Console# show spanning-tree Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority Address - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 322
www.dell.com | support.dell.com 1/e4 1/e5 Enabled 128.4 20000 BLK Enabled 128.5 20000 DIS ALTN No - - Shared (STP) - Console# show spanning-tree Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority 36864 Address 00:02:4b:29:7a:00 This switch is the root - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 323
Console# show spanning-tree Spanning tree disabled (BPDU filtering) mode RSTP Default port cost method: long Root ID Priority Address Path Cost Root Port Hello Time N/A N/A N/A N/A N/A Max Age N/A Forward Delay N/A Bridge ID Priority Address - - - - - DELL CONFIDENTIAL - PRELIMINARY 9/13/ - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 324
dell.com | support.dell.com Console# show spanning-tree active Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority Address Path Cost Root Port Hello Time 2 sec 32768 00:01:42:97:e0:00 20000 1 (1/e1) Max Age 20 sec Forward Delay 15 sec Bridge ID Priority Address - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 325
Role ---ALTN PortFast Type No Shared (STP) Console# show spanning-tree detail Spanning tree enabled mode RSTP Default port cost method: long Root ID Priority 32768 Address 00:01:42:97:e0:00 Path Cost 20000 Root Port 1 (1/e1) DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 326
Type: Shared (configured: auto) STP Port Fast: No (configured:no) Designated bridge Priority: 32768 Address: 00:02:4b:29:7a:00 Designated port id: 128.2 Designated path cost: 20000 Number of transitions to forwarding state: 1 BPDU: sent 2, received 170638 DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 327
id: 128.5 Port cost: 20000 Type: N/A (configured: auto) Port Fast: N/A (configured:no) Designated bridge Priority: N/A Address: N/A Designated port id: N/A Designated path cost: N/A Number of transitions to forwarding state: N/A BPDU: sent N/A, received N/A DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 328
www.dell.com | support.dell.com Console# show spanning-tree ethernet 1/e1 Port 1 (1/e1) enabled State: Forwarding Role: Root Port id: 128.1 Port cost: 20000 Type: P2p (configured: auto) RSTP Port Fast: No (configured:no) Designated bridge Priority: 32768 Address: 00:01:42:97:e0:00 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 329
Delay 15 sec IST Master ID Priority 32768 Address 00:02:4b:29:7a:00 This switch is the IST master. Hello Time 2 Vlans Mapped: 10-20 CST Root ID Priority 24576 Address 00:02:4b:29:89:76 Path Cost 20000 Root Port 4 (1/e4) Rem hops 19 Bridge ID Priority 32768 Address 00:02:4b:29:7a:00 DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 330
Type No P2p Bound (RSTP) No Shared Bound (STP) No P2p No P2p Console# show spanning-tree detail Spanning tree enabled mode MSTP Default port cost method: long ###### MST 0 Vlans Mapped: 1-9, 21-4094 CST Root ID Priority 32768 Address 00:01:42:97:e0:00 Path Cost 20000 Root - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 331
Type: Shared (configured: auto) Internal Port Fast: No (configured:no) Designated bridge Priority: 32768 Address: 00:02:4b:29:7a:00 Designated port id: 128.3 Designated path cost: 20000 Number of transitions to forwarding state: 1 BPDU: sent 2, received 170638 DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 332
.2 Number of transitions to forwarding state: 1 BPDU: sent 2, received 170638 Role: Designated Port cost: 20000 Port Fast: No (configured:no) Address: 00:02:4b:29:7a:00 Designated path cost: 20000 ###### MST 1 Vlans Mapped: 10-20 Root ID Priority 24576 Address 00:02:4b:29:89:76 Path Cost 20000 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 333
Type: Shared (configured: auto) Internal Port Fast: No (configured:no) Designated bridge Priority: 32768 Address: 00:02:4b:29:7a:00 Designated port id: 128.2 Designated path cost: 20000 Number of transitions to forwarding state: 1 BPDU: sent 2, received 170638 DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 334
www.dell.com | support.dell.com Console# show spanning-tree Spanning tree enabled mode MSTP Default port cost method: long ###### MST 0 Vlans Mapped: 1-9, 21-4094 CST Root ID Priority 32768 Address 00:01:42:97:e0:00 Path Cost 20000 Root Port 1 (1/e1) Hello Time 2 sec Max Age 20 sec - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 335
the interface. Syntax spanning-tree guard root no spanning-tree guard root Default Configuration Root guard is disabled. Command Modes Interface configuration (Ethernet, port-channel). User Guidelines Root guard can be enabled when the switch works in STP, RSTP and MSTP. When root guard is enabled - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 336
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 336 Spanning-Tree Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 337
). Default Configuration The default port number is 22. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example specifies the port to be used by the SSH server as 8080. Console(config)# ip ssh port 8080 ip ssh server The ip - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 338
.dell.com | support.dell.com Default Configuration Device configuration from a SSH server is enabled. Command Mode Global Configuration mode User Guidelines Global Configuration mode commands. Example The following example enables configuring the device from a SSH server. Console(config)# ip ssh - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 339
key pairs. Console(config)# crypto key generate dsa crypto key generate rsa The crypto key generate rsa Global Configuration mode command generates RSA key pairs. Syntax crypto key generate rsa Default Configuration RSA key pairs do not exist. Command Mode Global Configuration mode User Guidelines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 340
www.dell.com | support.dell.com Syntax ip ssh pubkey-auth no ip ssh pubkey-auth Default Configuration Public Key authentication for incoming SSH sessions is disabled. Command Mode Global Configuration mode User Guidelines AAA authentication is independent Example The following example enables - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 341
example enters the SSH Public Key-chain Configuration mode and manually configures the RSA key pair for SSH public key-chain bob. Console(config)# crypto key pubkey-chain ssh Console(config-pubkey-chain)# user-key bob Console(config-pubkey-key)# key-string rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCvTnRwPWl - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 342
.com | support.dell.com Default Configuration No SSH public keys exist. Command Mode SSH Public Key-string Configuration mode User Guidelines Follow this command with the key-string SSH Public Key-String Configuration mode command to specify the key. Example The following example enables manually - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 343
with a key-string row command. This command is useful for configuration files. Example The following example enters public key strings for SSH public key client bob. Console(config)# crypto key pubkey-chain ssh Console(config-pubkey-chain)# user-key bob rsa Console(config-pubkey-key)# key-string - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 344
no user guidelines for this command. Example The following example displays the SSH server configuration. Console# show ip ssh SSH server enabled. Port: 22 RSA key was generated. DSA (DSS) key was generated. SSH Public Key Authentication is enabled. Active incoming sessions: IP address SSH - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 345
- Indicates the DSA key. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the SSH public RSA keys on the device. Console# show crypto key mypubkey - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 346
www.dell.com | support.dell.com show crypto key Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays SSH public keys stored on the device. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 347
crypto slogin key generate dsa Default Configuration DSA key pairs do not exist. Command Mode Global Configuration mode User Guidelines • Use this Console# config Console(config)# crypto slogin key generate dsa crypto slogin key generate rsa The crypto slogin key generate rsa Global Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 348
• rsa - Indicates the RSA key. • dsa - Indicates the DSA key. Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 348 SSH Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 349
following example displays the secure login public RSA keys of the device Console# show crypto slogin key mypubkey rsa RSA key data: 005C300D 86 Fingerprint(Bubble Babble): yteriuwt jgkljhglk yewiury hdskjfryt gfhkjglk DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY SSH Commands 349 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 350
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 350 SSH Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 351
on no logging on Default Configuration Logging is enabled. Command Mode Global Configuration mode User Guidelines • The logging Console(config)# logging on logging The logging Global Configuration mode command logs messages to a syslog server. To delete the syslog server with the specified address - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 352
Configuration mode User Guidelines • Up to 8 syslog servers can be used. • If no specific severity level is specified, the global values apply to each server. Example The following example limits logged messages sent to the syslog server with IP address 10.1.1.1 to severity level critical. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 353
debugging. Default Configuration The default severity level is informational. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example limits logging messages displayed on the console to severity level errors. Console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 354
The default number of messages is 200. Command Mode Global Configuration mode User Guidelines This command takes effect only after Reset. Example The following example changes the number of syslog messages stored in the internal buffer to 300. Console(config)# logging buffered size 300 DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 355
This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example clears messages from the internal logging buffer. Console# clear logging Clear logging buffer [yes/no]? logging file The - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 356
file. Syntax clear logging file Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example clears messages from the logging file. Console# clear logging file Clear - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 357
renaming operations. Default Configuration Logging file system events is enabled. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enables logging messages related to file copy operations. Console(config)# file - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 358
. Default Configuration Logging management ACL events is enabled. Command Mode Global Configuration mode User Guidelines Other types of management ACL events are not subject to this command. Example The following example enables logging messages related to deny actions of management ACLs. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 359
messages stored in the internal buffer. Console# show logging Logging is enabled. Console logging: level debugging. Console Messages: 0 Dropped (severity). Buffer Copy Enabled File system Delete-Rename Enabled Management ACL Deny Enabled DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 360
.dell.com | support.dell. to up 11-Aug-2004 15:41:43: %SYS-5-CONFIG_I: Configured from memory by console 11-Aug-2004 15:41:39: %LINEPROTO-5-UPDOWN: Line protocol on logging file Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 361
user guidelines for this command. Example The following example displays the logging state and the syslog messages stored in the logging file. Console# show logging file Logging is enabled. Console logging: level debugging. Console -Rename Enabled Management ACL Deny Enabled DELL CONFIDENTIAL - - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 362
dell.com | support.dell Aug-2004 15:41:43: %SYS-5-CONFIG_I: Configured from memory by console 11-Aug-2004 15:41:39: %LINEPROTO-5-UPDOWN settings of the syslog servers. Syntax show syslog-servers Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 363
Guidelines There are no user guidelines for this command. Example The following example displays the settings of the syslog servers. Console# show syslog-servers Device Configuration IP address Port 192.180.2.27 514 192.180.2.28 514 Severity Informational Warning Facility -------local7 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 364
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 364 Syslog Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 365
System Management ping The ping User EXEC mode command sends ICMP echo request packets to another node on the network. Syntax ping {ip-address | hostname }[size packet_size] [count packet_count] [timeout time_out] • ip-address - IP address to ping. • hostname - Host name to ping. (Range: 1-158 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 366
dell.com | support.dell.com Examples The following example displays pinging results: Console> , 0% packet loss round-trip (ms) min/avg/max = 7/8/11 Console> ping yahoo.com Pinging yahoo.com (66.218.71.198) with 64 /max = 7/8/11 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 366 System - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 367
60) • ip-address - One of the device's interface addresses to use as a source address for the probes. The device normally selects what it feels is the best source address to use. • tos - The Type-Of-Service byte in the IP Header of the packet. (Range: 0-255) Default Configuration The default number - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 368
dell.com | support.dell maximum TTL is exceeded or when the user interrupts the trace by pressing Esc. packets will actually take when traveling to their destination. Console> traceroute umaxp1.physics.lsa.umich.edu Type Esc to DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 368 System - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 369
reassembly time exceeded. S Source route failed. U Port unreachable. telnet The telnet User EXEC mode command enables logging on to a host that supports Telnet. Syntax telnet {ip-address | hostname} [port] [keyword1......] • ip-address - IP address of the destination host. • hostname - Host - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 370
.dell.com Default Configuration The default port is the Telnet port (decimal23) on the host. Command Mode User EXEC mode User Guidelines • Telnet software supports special Telnet commands in the form of Telnet sequences that map generic terminal control functions to operating system-specific - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 371
Protocol FTP data connections Gopher NIC hostname server Ident Protocol Internet Relay Chat Kerberos login Kerberos shell Login Printer service Network News Transport Protocol Port Number 179 19 514 13 9 53 7 512 79 21 20 70 101 113 194 543 544 513 515 119 DELL CONFIDENTIAL - PRELIMINARY 9/13 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 372
The resume User EXEC mode command enables switching to another open Telnet session. Syntax resume [connection] • connection - The connection number. (Range: 1 - 4 connections) Default Configuration The default connection number is that of the most recent connection. Command Mode User EXEC mode DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 373
are no user guidelines for this command. Examples The following command switches to open Telnet session number 1. Console> resume 1 reload The reload Privileged EXEC mode command reloads the operating system. Syntax reload Default Configuration This command has no default configuration. Command Mode - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 374
: 1-158 characters) Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example specifies the device host name. Console(config)# hostname Dell Dell(config)# stack - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 375
up-time if they were powered up within ten minutes of Default Configuration All units are reloaded. Command Modes Privileged EXEC mode User Guidelines If no unit is specified, all units are reloaded. Example The following example reloads Unit 2 of the stack. Console(config)# stack reload unit 2 DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 376
displays information about the status of a stack. Syntax show stack [unit unit] • unit- Specifies the number of the unit. (Range: 1-6) Default Configuration This command has no default configuration. Command Mode User EXEC mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 376 System - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 377
user guidelines for this command. Example The following example displays stack status. Console> show stack Unit Address Configured order: Unit 1 at Top, Unit 2 at bottom Console> show stack Unit Address Configured order: Unit 1 at Top, Unit 6 at bottom Can't display order as requested. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 378
www.dell.com | support.dell.com Console> show stack 1 Unit 1: MAC address: 00:00:b0:87:12:11 Master: Forced. Product: PowerCOnnect34xx. Software: 1.0.0.0 Status: Master Active image: image-1. Selected for next boot: image-2. show users The show users User EXEC mode command displays information - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 379
. Host Address Remote host to which the device is connected through a Telnet session. IP address of the remote host. Port Telnet TCP port number Byte Number of unread bytes for the user to see on the connection. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY System Management 379 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 380
Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the system information. Console> show system Unit ---1 Type PowerConnect 3424 Unit ---1 Main Power - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 381
This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays system version information (only for demonstration purposes). Console> show version SW version 1.0.0.0 (date - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 382
id [unit unit] • unit- Specifies the number of the unit. (Range: 1-6) Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 382 System - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 383
no service cpu-utilization Default Configuration Disabled. Command Mode Global Configuration mode User Guidelines • Use the show cpu utilization privileged EXEC command to view information on CPU utilization. Example This example enables measuring CPU utilization. Console# config Console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 384
This command has no default configuration. Command Modes Privileged EXEC mode User Guidelines • Use the service cpu-utilization Global Configuration mode command to enable measuring CPU utilization. Example The following example displays CPU utilization. Console# show cpu utilization CPU - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 385
address of the outgoing IP interface. • priority - Determines the order in which the TACACS+ servers are used, where 0 is the highest priority. (Range: 0 - 65535) Default Configuration No TACACS+ host is specified. If no port number is specified, default port number 49 is used. If no host-specific - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 386
128 characters) Default Configuration Empty string. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Examples The following example sets the authentication encryption key. Console(config)# tacacs-server key dell-s DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 387
example sets the timeout value to 30. Console(config)# tacacs-server timeout 30 tacacs-server source-ip The tacacs-server source-ip Global Configuration mode command configures the source IP address to be used for communication with TACACS+ servers. To return to the default configuration, use - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 388
and statistical information about a TACACS+ server. Console# show tacacs Device Configuration IP address Status Port Single TimeOut Source Connection IP 172.16.1.1 Connected 49 No Global Global Priority -------1 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 388 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 389
Global values TimeOut: 3 Device Configuration Source IP: 172.16.8.1 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY TACACS+ Commands 389 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 390
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 390 TACACS+ Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 391
EXEC mode: Console> enable enter password: Console# disable The disable Privileged EXEC mode command returns to the User EXEC mode. Syntax disable [privilege-level] • privilege-level - Privilege level to enter the system. (Range: 1 - 15) Default Configuration The default privilege level is 1. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 392
Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines There are no user guidelines for this command. Example The following example enters Privileged EXEC mode and logs in with username admin. Console> login User Name:admin Password:***** Console# DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 393
Global Configuration mode. Console# configure Console(config)# exit (Configuration) The exit command exits any configuration mode to the next highest mode in the CLI mode hierarchy. Syntax exit Default Configuration This command has no default configuration. Command Mode All configuration modes User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 394
. Syntax exit Default Configuration This command has no default configuration. Command Mode Privileged and User EXEC modes User Guidelines There are no user guidelines for this command. Example The following example closes an active terminal session. Console> exit DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 395
mode. Console(config)# end Console# help The help command displays a brief description of the help system. Syntax help Default Configuration This command has no default configuration. Command Mode All command modes User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 396
www.dell.com | support.dell.com Example The following example describes the help system. Console# help Help may be requested Syntax terminal datadump no terminal datadump Default Configuration Dumping is disabled. Command Mode User EXEC mode User Guidelines • By default, a More prompt is displayed - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 397
a show command. Console> terminal datadump show history The show history User EXEC mode command lists the commands entered in the current session. Syntax show history Default Configuration This command has no default configuration. Command Mode User EXEC mode User Guidelines • The buffer - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 398
.dell.com | support.dell.com show privilege The show privilege Privileged/User EXEC mode command displays the current privilege level. Syntax show privilege Default Configuration This command has no default configuration. Command Mode Privileged and User EXEC modes User Guidelines There are no user - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 399
has no default configuration. Command Mode Global Configuration mode User Guidelines There are no user guidelines for this command. Example The following example enters the VLAN database mode. Console(config)# vlan database Console(config-vlan)# vlan Use the vlan VLAN Configuration mode command - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 400
support.dell.com Default Configuration This command has no default configuration. Command Mode VLAN Configuration mode User Guidelines There are no user guidelines for this command. Example The following example VLAN number 1972 is created. Console(config)# vlan database Console(config-vlan)# vlan - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 401
and no spaces; a hyphen designates a range of IDs. • all - All existing static VLANs. Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines • Commands under the interface range context are executed independently on each interface in - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 402
private-vlan primary Default Configuration No PVLANs are configured. Command Mode Interface Configuration (VLAN) mode User Guidelines • An IP interface cannot be defined on a primary VLAN. • A primary VLAN cannot be defined if an IP interface has been configured on it. • The command is not supported - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 403
(config-vlan)# vlan 200 Console(config-vlan)# exit Console(config)# interface vlan 200 Console(config-if)# private-vlan primary private-vlan isolated The private-vlan isolated Interface Configuration mode command configures the isolated VLAN of the PVLAN. To return to the default configuration, use - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 404
| support.dell.com Example This example configures VLAN 20 as the isolated VLAN of primary private VLAN 200. Console# config Console(config)# vlan database Console(config-vlan)# vlan 200 Console(config-vlan)# exit Console(config)# interface vlan 200 Console(config-if)# private-vlan primary Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 405
the default VLAN (whose VID=1). Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines • A port cannot be defined as promiscuous or isolated if it is a member of a VLAN. • If a port is defined as promiscuous or isolated, it is no longer a member of the default VLAN. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 406
of the VLAN to which the port is configured. • dynamic-Indicates that the port is assigned to a VLAN based on the source MAC address of the host connected to the port. Default Configuration All ports belong to VLAN 1. Command Mode Interface configuration (Ethernet, port-channel) mode User Guidelines - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 407
ID of the primary VLAN. • cvlan- Specifies the ID of the community VLAN. Default Configuration The port is not a member of a PVLAN. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines • The community VLAN should be associated with the primary VLAN by using the private - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 408
www.dell.com | support.dell.com Example This example configures private VLAN 200 as the primary private VLAN and associates it with promiscuous private VLAN Ethernet port 1/e10. Console# config Console(config)# vlan database Console(config-vlan)# vlan 200 Console(config-vlan)# exit Console(config)# - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 409
specific private VLANs. Console# show vlan private-vlan Primary ------100 200 Isolated -------101 201 Community --------102, 103 202, 203 Console# show vlan private-vlan primary 100 Primary VLAN: 100 Isolated VLAN: 101 Community VLANs: 102, 103 Promiscuous ports: 1/e19, 2/e19 Isolated ports - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 410
Default Configuration This command has no default configuration. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example adds VLANs 1, 2, 5 to 6 to the allowed list of Ethernet port 1/e16. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 411
the VLANs. • untagged - Indicates that the port transmits untagged packets for the VLANs. Default Configuration If the port is added to a VLAN without specifying tagged or untagged, the default setting is tagged. Command Mode Interface Configuration (Ethernet, port-channel) mode DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 412
www.dell.com | support.dell.com User Guidelines • This command enables changing the egress rule (e.g., from tagged to untagged) without first removing the VLAN from the list. Example The following example adds VLANs 2, 5, and 6 to the allowed list of Ethernet port 1/e16 . Console(config)# interface - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 413
filtering disable Default Configuration Ingress filtering is enabled. Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines There are no user guidelines for this command. Example The following example disables port ingress filtering on Ethernet port 1/e16. Console(config - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 414
)# interface ethernet 1/e16 Console(config-if)# switchport general acceptable-frame-type tagged-only switchport forbidden vlan The switchport forbidden vlan Interface Configuration mode command forbids adding specific VLANs to a port. To return to the default configuration, use the remove parameter - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 415
vlan-id - VLAN ID of the customer Default Configuration No VLAN is configured Command Mode Interface configuration (Ethernet, port-channel) User Guidelines There are no user Guidelines for this command Example The following example sets the port's VLAN when the interface is in customer mode. Console - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 416
.dell.com | support.dell.com Command Mode Interface Configuration (Ethernet, port-channel) mode User Guidelines • An internal usage VLAN is required when an IP interface is configured on an Ethernet port or port-channel. • This command enables the user to configure the internal usage VLAN of a port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 417
Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the MAC-to-VLAN database. Console# show vlan mac-to-vlan MAC Address ----------- VLAN ---- DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 418
string. (Range: 1 - 32 characters) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays all VLAN information. Console# show vlan VLAN ---1 10 11 20 21 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 419
Console# show vlan internal usage VLAN ---1007 1008 1009 Usage --------Eth 1/e21 Eth 1/e22 Eth 1/e23 IP address ---------Active Inactive Active Reserved -------No Yes Yes show interfaces switchport The show interfaces switchport Privileged EXEC mode command displays the switchport configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 420
www.dell.com | support.dell.com Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays the switchport configuration for Ethernet port 1/e1. Console# show interface switchport ethernet 1/e1 Port 1/e1: VLAN Membership - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 421
Port is statically configured to: Vlan Name Egress rule ---- ------- ----------- 1 default untagged 11 VLAN011 tagged 19 IPv6 VLAN untagged 72 VLAN0072 untagged Forbidden VLANS: VLAN Name ---- ---- 73 out Console# show interface switchport ethernet 1/e2 Port 1/e2: VLAN - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 422
www.dell.com | support.dell.com Port is statically configured to: Vlan Name Egress rule ---- ------------ ----------- 8 VLAN0072 untagged 91 IP Telephony tagged Forbidden VLANS: VLAN Name ---- ---- 73 out Port 2/e19 VLAN Membership mode: Private-VLAN Community Primary VLAN: 2921 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 423
Port is member in: Vlan Name ---- ------------ 2921 Primary A 2922 Community A1 Egress rule ----------untagged untagged Type -----Static Static Static configuration: PVID: 2922 Ingress Filtering: Enabled Acceptable Frame Type: Untagged GVRP status: Disabled DELL CONFIDENTIAL - - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 424
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 424 VLAN Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 425
Default Configuration HTTP server is enabled. Command Mode Global Configuration mode User Guidelines • Only a user with access level 15 can use the Web server. Example The following example enables configuring the device from a browser. Console(config)# ip http server ip http port The ip http port - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 426
| support.dell.com Default Configuration The default port number is 80. Command Mode Global Configuration mode User Guidelines • Specifying 0 as the port number effectively disables HTTP access to the device. Example The following example configures the http port number to 100. Console(config)# ip - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 427
) Default Configuration The default port number is 443. Command Mode Global Configuration mode User Guidelines • Specifying 0 as the port number effectively disables HTTPS access to the device. Example The following example configures the https port number to 100. Console(config)# ip https port 100 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 428
no URL or IP address is specified, the default common name is the lowest IP address of the device at the time that the certificate is generated. If the number of days is not specified, the default period of time that the certification is valid is 365 days. Command Mode Global Configuration mode User - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 429
fully qualified URL or IP address of the device. (Range Default Configuration There is no default configuration for this command. Command Mode Privileged EXEC mode User Configuration mode command to import the certificate into the device. This certificate replaces the self-signed certificate. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 430
dell.com | support.dell.com Examples The following example generates and displays a certificate request for HTTPS. Console number. (Range: 1 - 2) Default Configuration This command has no default configuration. Command Mode Global Configuration mode DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 431
configuration (which is never displayed to the user or backed up to another device). Examples The following example imports a certificate signed by Certification Authority for HTTPS. Console DC789788 DC88A988 127897BC BB789788 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Web Server 431 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 432
www.dell.com | support.dell.com ip https certificate The ip https certificate Global Configuration mode command configures the active certificate for HTTPS. To return to the default configuration, use the no form of this command. Syntax ip https certificate number no ip https certificate • number - - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 433
displays the certificate. Console# show crypto certificate HTTP server configuration. Syntax show ip http Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 434
www.dell.com | support.dell.com Example The following example displays the HTTP server configuration. Console# show ip http HTTP server enabled. Port: 80 show ip https The show ip https Privileged EXEC mode command displays the HTTPS server configuration. Syntax show ip https Default Configuration - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 435
Certificate 2 is inactive Valid From: Jan 1 02:44:50 2004 GMT Valid to: Dec 31 02:44:50 2005 GMT Subject: CN= router.gm.com, 0= General Motors, C= US Finger print: 1873B936 88DC3411 BC8932EF 782134BA DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY Web Server 435 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 436
www.dell.com | support.dell.com DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 436 Web Server - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 437
no authentication Default Configuration No authentication method is defined. Command Mode Global Configuration mode User Guidelines must support MD-5 challenge and EAP type frames. • The device accepts EAP frames with a priority tag and also accepts EAP packets with VLAN tags. DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 438
802.1x globally. Console(config)# dot1x system-auth-control dot1x port-control The dot1x port-control Interface Configuration mode command enables manually controlling the authorization state of the port. To return to the default configuration, use the no form of this command. DELL CONFIDENTIAL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 439
by the client to authenticate. The device cannot provide authentication services to the client through the interface. Default Configuration Port is in the force-authorized state Command Mode Interface Configuration (Ethernet) User Guidelines • It is recommended to disable spanning tree or to - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 440
www.dell.com | support.dell.com Syntax dot1x re-authentication no dot1x re-authentication Default Configuration Periodic re-authentication is disabled. Command Mode Interface Configuration (Ethernet) User Guidelines There are no user guidelines for this command. Examples The following example - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 441
: unit/port) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following command manually initiates a re-authentication of 802.1X-enabled Ethernet port 1/e16. Console# dot1x - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 442
circumstances, such as unreliable links or specific behavioral problems with certain clients and authentication servers. • To provide a faster response time to the user, a smaller number than the default value should be entered. Examples The following example sets the number of seconds that the - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 443
Interface Configuration (Ethernet) mode User Guidelines • The default value of this command should be changed only to adjust for unusual circumstances, such as unreliable links or specific behavioral problems with certain clients. and authentication servers Examples The following command sets the - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 444
Interface configuration (Ethernet) mode User Guidelines • The default value of this command should be changed only to adjust for unusual circumstances, such as unreliable links or specific behavioral problems with certain clients. and authentication servers Examples The following example sets the - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 445
sets the time for the retransmission of packets to the authentication server to 3600 seconds. Console port. (Full syntax: unit/port) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 446
www.dell.com | support.dell.com Example The following example displays the status of 802.1X-enabled Ethernet ports. Console# show dot1x 802.1x is enabled Port ---1/ (HH:MM:SS): 08:19:17 MAC Address: 00:08:78:32:98:78 DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 446 802.1x Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 447
from the client before resending the request. Time in seconds the switch waits for a response from the authentication server before resending the request. The amount of time the user is logged in. The supplicant MAC address. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR PROOF ONLY 802.1x Commands - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 448
(Range: 1-160 characters) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Example The following example displays 802.1X users. Console# show dot1x users Port Username 1/e1 Bob 1/e2 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 449
statistics ethernet interface • interface - Valid Ethernet port. (Full syntax: unit/port) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. DELL CONFIDENTIAL - PRELIMINARY 9/13/06 - FOR - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 450
www.dell.com | support.dell.com Examples The following example displays 802.1X statistics for the specified interface. Console# show dot1x statistics ethernet 1/e1 EapolFramesRx: 11 EapolFramesTx: 12 EapolStartFramesRx: 12 EapolLogoffFramesRx: 1 EapolRespIdFramesRx: 3 EapolRespFramesRx: 6 - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 451
no dot1x auth-not-req Default Configuration Access is enabled. Command Mode Interface Configuration (VLAN) mode User Guidelines • An access port cannot be a member in an unauthenticated VLAN. • The native VLAN of a trunk port cannot be an unauthenticated VLAN. • For a general port, the PVID can be - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 452
www.dell.com | support.dell.com dot1x multiple-hosts The dot1x multiple-hosts Interface Configuration mode command enables multiple hosts (clients) on an 802.1X-authorized port, where the authorization state of the port is set to auto. To return to the default configuration, use the no form of this - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 453
are not the supplicant address and sends consecutive traps at intervals of 100 seconds. Console(config-if)# dot1x single-host-violation forward trap 100 dot1x guest-vlan The dot1x guest-vlan Interface Configuration mode command defines a guest VLAN. To return to the default configuration, use the no - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 454
www.dell.com | support.dell.com User Guidelines • Use the dot1x guest-vlan enable Interface Configuration mode command to enable unauthorized users on an interface to access the guest VLAN. • If the guest VLAN is defined and enabled, the port automatically joins the guest VLAN when the port is - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 455
: unit/port) Default Configuration This command has no default configuration. Command Mode Privileged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays 802.1X advanced features for the device. Console# show dot1x advanced Guest VLAN - Dell PowerConnect 3424P | Command
Line Interface (CLI) Guide (.htm) - Page 456
.dell.com | support.dell.com Console# show dot1x advanced ethernet 1/e1 Interface --------1/e1 Multiple Hosts Disabled Guest VLAN ---------Enabled Single host parameters Violation action: Discard Trap: Enabled Trap frequency: 100 Status: Single-host locked Violations since last trap: 9 DELL
www.dell.com | support.dell.com
Dellâ„¢ PowerConnectâ„¢ 3400 Series
CLI Reference Guide