Dell PowerConnect B-RX4 Installation Guide

Dell PowerConnect B-RX4 Manual

Get Dell PowerConnect B-RX4 PDF manuals and user guides View all Dell PowerConnect B-RX4 manuals
Add to My Manuals
Save this manual to your list of manuals

Dell PowerConnect B-RX4 manual content summary:

  • Dell PowerConnect B-RX4 | Installation Guide - Page 1
    53-1001811-01 January 31, 2010 BigIron RX Installation Guide Supporting BigIron RX running software release 02.7.02 53-1001811-01 *53-1001811-01*
  • Dell PowerConnect B-RX4 | Installation Guide - Page 2
    dell.com at the following location: www.dell.com/regulatory_compliance. CAUTION A CAUTION indicates potential damage to hardware or loss of data if instructions the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names
  • Dell PowerConnect B-RX4 | Installation Guide - Page 3
    About This Document In this chapter ix Audience ix Supported hardware and software ix Document conventions ix Text formatting system 18 LEDs 22 Rack mount kit 22 Supported software features 23 Chapter 2 Installing a BigIron RX Series Switch In this chapter 25 Installation precautions
  • Dell PowerConnect B-RX4 | Installation Guide - Page 4
    Port to a network 79 Powering-on the power source 79 Verifying proper operation 80 Observing the LEDs 80 Displaying the module status 85 iv BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 5
    modules 108 Troubleshooting network connections 109 Testing network connectivity 110 Pinging an IP address 110 Tracing a route 110 Using virtual cable testing to diagnose a cable 111 Managing the BigIron RX Series Chassis and Modules In this chapter 113 BigIron RX Installation Guide v 53
  • Dell PowerConnect B-RX4 | Installation Guide - Page 6
    RX Series chassis 113 Displaying chassis status and temperature readings 113 Displaying the Syslog configuration and static and dynamic buffers 115 Managing the cooling system 117 Configuring the cooling system 117 Manually a power supply 147 vi BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 7
    BigIron RX Installation Guide 53-1001811-01 Replacing cooling system components 150 Replacing fan assemblies in the BigIron RX- 32 150 Replacing fan assemblies in the BigIron RX-16 153 Replacing the fan assembly in the BigIron RX-4 and BigIron RX-8 155 Replacing the air filters in a BigIron RX
  • Dell PowerConnect B-RX4 | Installation Guide - Page 8
    and Australia 207 Japan 207 Korea 208 Caution and Danger Notices Caution statements 209 Danger notices 216 Software Specifications IEEE compliance 223 RFC support 223 General protocols 223 BGP 224 OSPF 224 RIP 225 IP Multicast 225 Management 225 Internet drafts 226 viii BigIron
  • Dell PowerConnect B-RX4 | Installation Guide - Page 9
    OSPF, BGP, ISIS, IGMP, PIM, DVMRP, and VRRP. Supported hardware and software The following hardware platforms are supported by this release of this guide: • BigIron RX - 4 • BigIron RX - 8 • BigIron RX - 16 • BigIron RX - 32 Document conventions This section describes text formatting conventions and
  • Dell PowerConnect B-RX4 | Installation Guide - Page 10
    . Notes, cautions, and danger notices The following notices and statements are used in this manual. They are listed below in order of increasing severity of potential hazards. NOTE A note the properties of their respective companies and corporations. x BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 11
    in this guide: • BigIron RX Series Configuration Guide. • IronView MIB Reference Manual. • IronView Network Manager User Guide. NOTE For 8061 International: +800-ATFIBREE (+800 28 34 27 33) Refer to the Services & Support page on www.brocade.com for additional toll-free numbers that may be available
  • Dell PowerConnect B-RX4 | Installation Guide - Page 12
    xii BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 13
    Supported software features 23 Product overview The BigIron RX Series switch provides high-performance L2/3 switching for the Enterprise, large data centers, and grid computing topologies. The BigIron RX to your existing management network. BigIron RX Installation Guide 1 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 14
    1 BigIron RX-4 chassis 1 2 3 4 5 6 7 8 1 Interface slot 2 2 Switch fabric slot 2 3 Switch fabric slot 3 4 ESD connector 5 Interface slot 1 9 10 6 Switch fabric slot 1 7 Interface slot 3 8 Management slot 1 9 Management slot 2 10 Interface slot 4 2 BigIron RX Installation Guide 53-1001811
  • Dell PowerConnect B-RX4 | Installation Guide - Page 15
    FIGURE 2 BigIron RX-8 chassis 1 3 6 8 10 12 Hardware features 1 2 4 5 7 9 11 13 14 1 Interface slot 1 2 Interface slot 2 3 Interface slot 3 4 Interface slot 4 5 2 16 Power supply slot 3 17 Power supply slot 4 18 ESD connector 17 18 BigIron RX Installation Guide 3 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 16
    1 Hardware features FIGURE 3 BigIron RX-16 chassis 1 3 5 7 17 19 9 11 13 23 15 21 22 2 4 6 8 18 20 10 12 14 16 1 Interface slot 1 2 Interface fabric slot 3 20 Switch fabric slot 4 21 Management slot 1 22 Management slot 2 23 ESD connector 4 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 17
    FIGURE 4 BigIron RX-32 chassis Hardware features 1 Pwr Active Pwr Active 1 3 5 7 33 35 9 11 13 15 2 4 6 8 34 41 36 10 12 14 fabric slot 6 39 Switch fabric slot 7 40 Switch fabric slot 8 41 Management slot 1 42 Management slot 2 43 Captive screws BigIron RX Installation Guide 5 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 18
    or blank power supply faceplate, respectively. BigIron RX-8 Upon shipment from the factory, the following components are installed in the BigIron RX-8 chassis as described: • Two switch fabric two management modules (one active and one redundant). 6 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 19
    BigIron RX-16 Upon shipment from the factory, the following components are installed in the BigIron RX- BigIron RX-32 Upon shipment from the factory, the following components are installed in the BigIron RX-32 faceplate, respectively (BigIron RX-4, -8, and 16). On the BigIron RX-32, before installing
  • Dell PowerConnect B-RX4 | Installation Guide - Page 20
    cannot use management modules designed for the BigIron RX-32 in any of the other Brocade device, because it will not function properly. A management module is hot swappable, which allows you to remove and replace it without powering down the system. 8 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 21
    slots • A Console port • A 10/100/1000 Ethernet port • Six LEDs PCMCIA slots The PCMCIA slots support a flash PC card. The flash PC card provides storage space in addition to the system's flash memory. A the control plane only and not the data plane. BigIron RX Installation Guide 9 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 22
    install up to 32 BigIron RX Series interface modules in the BigIron RX Series chassis as described: • BigIron RX-4: Supports up to 4 interface modules • BigIron RX-8: Supports up to 8 interface modules • BigIron RX-16: Supports up to 16 interface modules • BigIron RX-32: Supports up to 32 interface
  • Dell PowerConnect B-RX4 | Installation Guide - Page 23
    A two 10 Gigabit Ethernet module contain two physical ports, through which you can connect your BigIron RX Series switch to other network devices at a speed of 10 Gigabits. Into a physical port, LEDs on the 10 Gigabit Ethernet module's front panel. BigIron RX Installation Guide 11 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 24
    16-port 10 Gigabit Ethernet oversubscribed module The 16 x 10GE oversubscribed module for the BigIron RX plugs into any port slot of the BigIron switch and is compatible with all previous generations of the 10 Gigabit Ethernet module's front panel. 12 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 25
    card. You can monitor traffic on 16x10 ports. • Brocade currently only support "strict" and "destination-weighted" scheduling schemes (qos scheduler). Refer to the Configuring QoS chapter in the BigIron RX Configuration Guide for more informaton. 10 Gigabit Ethernet ports A 16 x 10 Gigabit Ethernet
  • Dell PowerConnect B-RX4 | Installation Guide - Page 26
    mini-GBIC (SFP) ports TABLE 5 Gigabit Ethernet module LEDs Position State Meaning Below each Ethernet port (left-side LED supports port in top row while right-side LED supports port in bottom row) On or blinking Off for an extended period The port is transmitting and receiving packets. The
  • Dell PowerConnect B-RX4 | Installation Guide - Page 27
    31 37 43 1 2 3 4 5 6 7 8 1 Ports 1 -6 2 Ports 7-12 3 Ports 13 -18 4 Ports 19 -24 5 Ports 25-30 6 Ports 31-36 7 Ports 37-42 8 Ports 43-48 BigIron RX Installation Guide 15 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 28
    for each port. Cables and patch panels that support this module are available through any Tyco International distribution RX Series chassis, the chassis and switch fabric module will not function properly. Figure 11 shows the switch fabric module's front panel. 16 BigIron RX Installation Guide
  • Dell PowerConnect B-RX4 | Installation Guide - Page 29
    active and cannot switch user packets. Power supplies The BigIron RX Series switches support the following power supply options: • BigIron RX-4: Accommodates three power supplies (AC or DC) with one supply's workload to the remaining power supplies. BigIron RX Installation Guide 17 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 30
    contain a 4-speed fan that pulls air through the chassis. The BigIron RX-16 is equipped with eight controllers to support redundancy. • BigIron RX-32: Is equipped with ten fan assemblies in the rear of the chassis not recognize the new controller. 18 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 31
    FIGURE 12 Fan component locations for the BigIron RX-4 Hardware features 1 1 1 Fan module FIGURE 13 Fan component locations for the BigIron RX-8 1 1 Fan module BigIron RX Installation Guide 19 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 32
    1 Hardware features FIGURE 14 Front fan component locations for the BigIron RX-16 1 1 Front fan assembly FIGURE 15 Rear fan component locations for the BigIron RX-16 1 1 Fan modules 20 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 33
    FIGURE 16 Rear fan component locations for the BigIron RX-32 Hardware features 1 2 1 4 3 6 5 8 7 10 9 1 Fan module 1 2 Fan module 2 3 module 10 Upon system startup, the fans in the BigIron RX Series switches operate at high speed, then the management module lowers the fan speed to low speed
  • Dell PowerConnect B-RX4 | Installation Guide - Page 34
    to center-mount the BigIron RX chassis using two L-shaped mounting brackets. The mid-mount kit comes with instructions for installing the mounting number of BigIron RX Series chassis depending on the model: • BigIron RX-32 - 1 BigIron RX-32 chassis 22 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 35
    features supported on the BigIron RX Series switch, refer to the software release notes for this device. For information about configuring basic, non-protocol software features supported on this device,refer to the BigIron RX Series Configuration Guide. BigIron RX Installation Guide 23 53
  • Dell PowerConnect B-RX4 | Installation Guide - Page 36
    1 Supported software features 24 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 37
    that apply to the entire family of BigIron RX Series switches. DANGER The procedures in this manual are for qualified service personnel. DANGER If the installation requires a . Follow these precautions when installing a BigIron RX Series switch. BigIron RX Installation Guide 25 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 38
    AC power supplies installed in the chassis. DANGER Disconnect the power cord from all power sources to completely remove power from the device. 26 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 39
    near the input power connectors. CAUTION BigIron RX-4, -8, and -16 devices with DC power area is where access can be gained only by service personnel through the use of a special tool, lock CAUTION All devices with AC power sources (BigIron RX-32 only) are intended for installation in restricted
  • Dell PowerConnect B-RX4 | Installation Guide - Page 40
    enclosure. For BigIron RX-16, -8, and RX-4 switch This section describes the steps you will perform to install a BigIron RX-4 switch: • "Preparing the installation site" • "Unpacking a BigIron RX-4 switch" • "Chassis lifting guidelines for BigIron RX-4 switches" 28 BigIron RX Installation Guide
  • Dell PowerConnect B-RX4 | Installation Guide - Page 41
    module slots. NOTE You must provide standard #12-24 pan-head screws for mounting the BigIron RX-4 chassis into a rack. • CD-ROM containing software images and the user documentation (including this guide). • Warranty card. • A 115V AC power cable for each AC power supply you purchase from Brocade
  • Dell PowerConnect B-RX4 | Installation Guide - Page 42
    if necessary. In a standard 19-inch (EIA310-D) rack, you can install up to ten BigIron RX-4 chassis. For each BigIron RX-4 chassis that you install in a rack, you must provide four standard #12-24 pan-head . Figure 17 shows the location of the screws. 30 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 43
    front 2 Shipping screws 3 Chassis rear Mounting a BigIron RX-4 chassis in a rack Follow the steps given below to mount a BigIron RX-4 chassis in a rack. 1. Determine the position of Unequal flange equipment rack 3" 2 2 Network equipment rack BigIron RX Installation Guide 31 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 44
    portion of each keyhole slot over the corresponding screw in the rack. FIGURE 19 Mounting the BigIron RX-4 or BigIron RX-8 chassis in a rack 1 1 Standard 19 inch rack 4. Slide the chassis down so that place when removing adjacent panels or modules. 32 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 45
    system may overheat. If you are installing a redundant management module, refer to the Using a Redundant Management Module chapter in the BigIron RX Configuration Guide for information about how the redundant module works, optional software configurations that you can perform, and how to manage the
  • Dell PowerConnect B-RX4 | Installation Guide - Page 46
    the backplane. Modules have a snug fit for maximum EMI protection. NOTE The installation instructions for installing modules shown in the following illustrations are exactly the same for interface, screws further using the flat-head screwdriver. 34 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 47
    side of the power supply slot and make sure the power supply is properly inserted in the guides. Never insert the power supply upside down. FIGURE 21 Installing a power supply in a BigIron RX-4 chassis 1 1 Power supply 4. After the power supply is fully inserted, push the power supply front panel
  • Dell PowerConnect B-RX4 | Installation Guide - Page 48
    RX-4 chassis. This is supported through use of a DC-to-DC power supply. DC power must be supplied at 48 V and 30 A. The DC-to-DC supply provides the DC power to the chassis at 12 V and 100 A. DANGER The procedure in this section is for qualified service personnel. 36 BigIron RX Installation Guide
  • Dell PowerConnect B-RX4 | Installation Guide - Page 49
    remove the two screws holding the transparent cover over the power supply lugs. FIGURE 23 The BigIron RX-4 DC power supply 1 DC DC ALM IN OK 2 1 Screws holding power lugs 2 Screws " • "Powering-on the power source" • "Verifying proper operation" BigIron RX Installation Guide 37 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 50
    any items are missing, contact the place of purchase: • BigIron RX-8 chassis with the appropriate number of switch fabric modules already installed mounting the BigIron RX Series chassis into a rack. • CD-ROM containing software images and the user documentation (including this guide). • Warranty
  • Dell PowerConnect B-RX4 | Installation Guide - Page 51
    necessary. In a standard 19-inch (EIA310-D) rack, you can install up to six BigIron RX-8 chassis. For each BigIron RX-8 chassis that you install in a rack, you must provide four standard #12-24 pan-head . Figure 25 shows the location of the screws. BigIron RX Installation Guide 39 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 52
    front 2 Chassis rear 3 Shipping screws Mounting a BigIron RX-8 chassis in a rack Follow the steps given below to mount a BigIron RX-8, chassis in a rack. 1. Determine the position of Unequal flange equipment rack 3" 2 2 Network equipment rack 40 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 53
    portion of each keyhole slot over the corresponding screw in the rack. FIGURE 27 Mounting the BigIron RX-4 or BigIron RX-8 chassis in a rack 1 1 Standard 19-inch rack 4. Slide the chassis down so that place when removing adjacent panels or modules. BigIron RX Installation Guide 41 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 54
    may overheat. If you are installing a redundant management module, refer to the Using a Redundant Management Module chapter in the BigIron RX Series Configuration Guide for information about how the redundant module works, optional software configurations that you can perform, and how to manage the
  • Dell PowerConnect B-RX4 | Installation Guide - Page 55
    the backplane. Modules have a snug fit for maximum EMI protection. NOTE The installation instructions for installing modules shown in the following illustrations are exactly the same for interface, the screws further using the flat-head screwdriver. BigIron RX Installation Guide 43 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 56
    slot and make sure the power supply is properly inserted in the guides. Never insert the power supply upside down. FIGURE 29 Installing a power supply in a BigIron RX-8 chassis 1 1 Power supply 4. For the BigIron RX-8 chassis, install a blank power supply faceplate into each slot that is empty
  • Dell PowerConnect B-RX4 | Installation Guide - Page 57
    power plug to hold it in place. FIGURE 30 Connecting a power cord to the power supply in a BigIron RX-8 chassis 1 2 3 1 Lift handle 2 Cord retainer 4 3 Power cord 4 Ground point DANGER If the refer to "Powering-on the power source" on page 79. BigIron RX Installation Guide 45 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 58
    RX-8 chassis. This is supported through use of a DC-to-DC power supply. DC power must be supplied at 48 V and 30 A. The DC-to-DC supply provides the DC power to the chassis at 12 V and 100 A. DANGER The procedure in this section is for qualified service BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 59
    to "Installing power supplies in a BigIron RX-16 chassis" on page 54, "Attaching a management station" on page 77, and "Connecting a BigIron RX Series switch" on page 105. Installation location the chassis, make sure you allow enough working room. BigIron RX Installation Guide 47 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 60
    screws. NOTE You must provide standard #12-24 pan-head screws for mounting the BigIron RX Series chassis into a rack. • CD-ROM containing software images and the user documentation (including this guide). • Warranty card. • A 115V AC power cable for each AC power supply you purchase from Brocade
  • Dell PowerConnect B-RX4 | Installation Guide - Page 61
    . In a standard 19-inch (EIA310-D) rack, you can install up to three BigIron RX-16 chassis. For each BigIron RX-16 chassis that you install in a rack, you must provide four standard #12-24 front-mount or mid-mount of the BigIron RX-16 chassis. BigIron RX Installation Guide 49 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 62
    16 chassis in a rack Follow the steps given below to mount a BigIron RX-16 chassis in a rack. 1. Determine the position of each chassis in the rack, for example, a chassis the wide portion of each keyhole slot over the corresponding screw in the rack. 50 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 63
    through step 5 to mount each subsequent chassis in the same rack. Removing the slot blanks The BigIron RX-16 chassis ships with slot blanks installed in all module slots. The slot blank covers a slot that and store it in a safe place for future use. BigIron RX Installation Guide 51 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 64
    may overheat. If you are installing a redundant management module, refer to the Using a Redundant Management Module chapter in the BigIron RX Series Configuration Guide for information about how the redundant module works, optional software configurations that you can perform, and how to manage the
  • Dell PowerConnect B-RX4 | Installation Guide - Page 65
    the module into the appropriate chassis slot and slide the card along the card guide until the ejectors on either side of the module move close to the module front panel. Refer to special instructions, "Populating a BigIron RX-16 chassis" on page 53. NOTE When inserting the module into the chassis
  • Dell PowerConnect B-RX4 | Installation Guide - Page 66
    power supply slot. 2. Remove the power supply from its packaging. 3. Insert the power supply into the empty power supply slot, using the guides provided on either side of the slot. FIGURE 36 Installing a power supply in a BigIron RX-16 chassis 1 1 Power supply 1 2 2 Release latch 54 BigIron
  • Dell PowerConnect B-RX4 | Installation Guide - Page 67
    Installing a BigIron RX-16 switch 2 CAUTION Carefully follow the mechanical guides on each side of the power supply slot and make sure the power supply is properly inserted in the guides. Never insert the power supply upside down. 4. After the power supply is fully inserted, push the power supply
  • Dell PowerConnect B-RX4 | Installation Guide - Page 68
    RX-16 chassis. This is supported through use of a DC-to-DC power supply. DC power must be supplied at 48 V and 30 A. The DC-to-DC supply provides the DC power to the chassis at 12 V and 100 A. DANGER The procedure in this section is for qualified service BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 69
    . For information on cabling, refer to "BigIron RX-32 cable routing" on page 67, "Installing power supplies in a BigIron RX-32 chassis" on page 75, "Attaching a management station" on page 77, and "Connecting a BigIron RX Series switch" on page 105. BigIron RX Installation Guide 57 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 70
    : • BigIron RX-32 chassis with the card slots empty, and covered with upper and lower shipping panels (refer to uncrating instructions next) • • CD-ROM containing software images and the user documentation (including this guide) • Warranty card • A 220-240V AC power cable for each AC power
  • Dell PowerConnect B-RX4 | Installation Guide - Page 71
    shipping panel) in case the chassis needs to be shipped again. Installing a BigIron RX-32 chassis in a rack This section describes the following tasks: • Preparing to Mount a BigIron RX-32 chassis in a Rack • Attaching mounting brackets to a chassis BigIron RX Installation Guide 59 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 72
    in a rack, positioned a low as possible. • The empty BigIron RX-32 chassis weighs approximately 325 lbs. You must use a mechanical device (such as a material lift or work positioner), and four people are required to guide the chassis into place. 60 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 73
    chassis to the inner pallet. Refer to Figure 41. FIGURE 41 Location of L-Brackets holding the BigIron RX-32 chassis 1 1 Remove brackets that hold chassis to base (two brackets on either side of chassis) in back, slide the chassis into the rack. BigIron RX Installation Guide 61 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 74
    ejectors in the outward position, insert the module into the appropriate chassis slot and slide the card along the card guide until the ejectors on either side of the module move close to the module front panel. Refer to special instructions, "BigIron RX-32 cable routing" on page 67. 62 BigIron
  • Dell PowerConnect B-RX4 | Installation Guide - Page 75
    in a BigIron RX-32 chassis Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active NOTE The installation instructions for installing modules tighten the screws further using the flat-head screwdriver. BigIron RX Installation Guide 63 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 76
    00 into slots 17 to 32 of a BigIron RX-32 chassis. They should only be inserted into slots initially installation of the modules into a BigIron RX-32, Brocade recommends inserting all the modules into screws into the chassis. When Populating the BigIron RX-32 chassis, the modules must be installed in
  • Dell PowerConnect B-RX4 | Installation Guide - Page 77
    FIGURE 43 BigIron RX-32 chassis Installing a BigIron RX-32 switch 2 Pwr Active Pwr Active 1 3 5 7 33 35 9 11 13 15 2 4 6 8 34 41 36 10 12 14 16 Pwr slot 29 30 Interface slot 30 31 nterface slot 31 32 nterface slot 32 33 Switch fabric slot 1 BigIron RX Installation Guide 65 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 78
    8 Using the Insertion or Extraction tool Due to the high density of cables that the BigIron RX-32 chassis can support, it may be difficult to insert and remove the RJ-45 and optical connectors. An insertion to be difficult to release and remove. 66 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 79
    this side to compress the locking tab while you remove the connector. BigIron RX-32 cable routing BigIron RX-32 cable management is designed to ensure access to the power supplies at the for clarity. FIGURE 45 BigIron RX-32 cable routing diagram BigIron RX Installation Guide 67 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 80
    2 Installing a BigIron RX-32 switch Details of cable routing are as follows: CAUTION Be sure not to exceed the minimum recommended bend cables to the left 1 2 3 4 1 Upper left quadrant 2 Side combs (18) 3 Cables from slot #1 4 Cables from slot #2 68 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 81
    Installing a BigIron RX-32 switch 2 FIGURE 47 Routing upper-left quadrant cables up 1 2 3 4 1 Upper left quadrant 2 Comb C (Slot #7 and #8 cables) 3 Comb B ( and #6 cables up through Comb B. 4. Route slot card #7 and #8 cables up through Comb C. BigIron RX Installation Guide 69 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 82
    2 Installing a BigIron RX-32 switch Cable routing for the upper-right quadrant Route slot cards in the numerical order starting with the cables the right 1 2 3 4 1 Upper right quadrant 2 Side combs (18) 3 Cables from slot #15 4 Cables from slot #16 70 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 83
    Installing a BigIron RX-32 switch 2 FIGURE 49 Routing upper-right quadrant cables up 1 2 3 4 1 Upper right quadrant 2 Comb C (Slot #9 and #10 cables) 3 Comb and #12 cables up through Comb B. 4. Route slot card #9 and #10 cables up through Comb C. BigIron RX Installation Guide 71 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 84
    2 Installing a BigIron RX-32 switch Cable routing for the lower-left quadrant 1. Route slot card #18 and #17 cables directly to the left cables to the left 1 2 3 4 1 Lower left quadrant 2 Cables from slot #17 3 Cables from slot #18 4 Side combs (18) 72 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 85
    Installing a BigIron RX-32 switch 2 FIGURE 51 Routing lower-left quadrant cables down 1 2 3 4 1 Lower left quadrant 2 Comb A (Slot #19 and #20 cables) and #21 cables down through Comb B. 4. Route slot card #24 and #23 cables down through Comb C. BigIron RX Installation Guide 73 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 86
    2 Installing a BigIron RX-32 switch Cable routing for the lower-right quadrant 1. Route slot card #32 and #31 cables directly to the right to the right 1 2 3 4 1 Lower right quadrant 2 Cables from slot #31 3 Cables from slot #32 4 Side combs (18) 74 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 87
    26 and #25 cables down through Comb C. Installing power supplies in a BigIron RX-32 chassis DANGER High Touch Current. Earth connection essential before connecting supply. Follow the supply slot, using the guides provided on either side of the slot. BigIron RX Installation Guide 75 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 88
    supply blank cover 8 Pull down on plunger to remove 9 Power supply CAUTION Carefully follow the mechanical guides on each side of the power supply slot and make sure the power supply is properly inserted in the to seat into the backplane connector. 76 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 89
    power supply. 3. Snap the cord retainer over the power plug to hold it in place. FIGURE 55 BigIron RX-32 power supply receptacle and cord retainer 1 AC OK DC OK 2 ALM 1 Cord retainer 2 Power (management) port using either Telnet or SSH. BigIron RX Installation Guide 77 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 90
    allow you to attach a PC or terminal. From the Console port, you can access the BigIron RX Series switch's CLI directly from the PC or terminal or through a Telnet connection to the PC or bits: 8 • Parity: None • Stop bits: 1 • Flow control: None 78 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 91
    : • "Connecting AC power to a BigIron RX-4 chassis" on page 36 • "Connecting AC power to a BigIron RX-8 chassis" on page 45 • "Connecting AC power to a BigIron RX-16 chassis" on page 55 • "Connecting AC power to a BigIron RX-32 chassis" on page 77 BigIron RX Installation Guide 79 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 92
    The BigIron RX Series switch is designed to provide uninterrupted service even when Verify that the BigIron RX Series switch has initialized the proper operation of the BigIron RX Series chassis after power on, the CLI Observing the LEDs After a BigIron RX Series chassis powers on, you can observe
  • Dell PowerConnect B-RX4 | Installation Guide - Page 93
    action Neither of the management modules is managing the switch fabric and interface modules. A problem could have occurred during initialization. Check your attached PC or terminal for possible error messages the other 10/100/1000 Ethernet port LED. BigIron RX Installation Guide 81 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 94
    interface module may be in interactive mode. Check the status of the module by entering the show module command at any CLI prompt. 82 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 95
    port is not transmitting or receiving user packets. For information about action you can take to troubleshoot the problem, refer to Table 16 on page 109. Pwr On Active On Power supplies AC The module • Make sure that the wall outlet has power. BigIron RX Installation Guide 83 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 96
    providing DC power to the BigIron RX Series chassis. The power supply is is lit Green, then there is a problem with the power supply and it must be Off providing DC power to the BigIron RX Series chassis. The power supply is in problem with the power supply and it must be replaced. The
  • Dell PowerConnect B-RX4 | Installation Guide - Page 97
    . If a problem persists after taking action described in this table, contact Brocade for technical support. Displaying the RX Series switch has initialized successfully, press Enter to display the following CLI prompt in the terminal emulation window: BigIron RX> BigIron RX Installation Guide
  • Dell PowerConnect B-RX4 | Installation Guide - Page 98
    the same serial port you attached to the Console port. If you see this prompt (BigIron RX>), you are now connected to the system and can display the status of the modules using have power. • CARD_STATE_UP - The module is up and operating normally. 86 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 99
    with an explanation for why the module is down, for example, "CARD_DOWN_REASON_BOOT_FAILED." If the explanation does not help you resolve the problem, you can contact Brocade technical support and provide the explanation included with this status. BigIron RX Installation Guide 87 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 100
    2 Verifying proper operation 88 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 101
    Cable Cinch Clips with mRJ-21 or RJ-45 cables. The following sections will provide detailed instructions: • "mRJ-21 procedures" on page 90 • "RJ-45 procedures" on page 94 4 6 7 1 Slot 1 2 Slot 2 3 Slot 3 4 Slot 4 5 Open end 6 Rear 7 Front BigIron RX Installation Guide 89 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 102
    strap through slot one and use the front and rear left recesses as shown in Figure 57. FIGURE 57 Two mRJ-21 cables 90 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 103
    Cinch with four mRJ-21 cables Four mRJ-21 cables may be secured as shown in Figure 59. FIGURE 59 Four mRJ-21 cables BigIron RX Installation Guide 91 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 104
    with six mRJ-21 cables Six mRJ-21 cables may be secured as shown in Figure 61. FIGURE 61 Six mRJ-21 cables 92 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 105
    Cinch with eight mRJ-21 cables Eight mRJ-21 cables may be secured as shown in Figure 63. FIGURE 63 Eight mRJ-21 cables BigIron RX Installation Guide 93 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 106
    RJ-45 cables, in two groups, may be secured as shown in Figure 65. FIGURE 65 12 RJ-45 cables in two groups 94 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 107
    24 RJ-45 cables, in four groups, may be secured as shown in Figure 67. FIGURE 67 24 RJ-45 cables in four groups BigIron RX Installation Guide 95 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 108
    RJ-45 cables, in six groups, may be secured as shown in Figure 69. FIGURE 69 36 RJ-45 cables in six groups 96 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 109
    48 RJ-45 cables, in eight groups, may be secured as shown in Figure 71. FIGURE 71 48 RJ-45 cables in eight groups BigIron RX Installation Guide 97 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 110
    3 RJ-45 procedures 98 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 111
    105 •Connecting a BigIron RX Series switch 105 •Testing network connectivity 110 Assigning passwords DANGER The procedures in this manual are for qualified service personnel. When you create format to take advantage of this password enhancement. BigIron RX Installation Guide 99 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 112
    a new password to the user. To configure a user password to expire, enter the following: BigIron RX(config)#username sandy expires 20 Syntax: username expires Enter 1 - 365 for number you cannot configure system or port parameters. 100 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 113
    RX> enable BigIron RX# 2. Access the CONFIG level of the CLI by entering the following command: BigIron RX# configure terminal BigIron RX(config port configuration and read-only passwords: BigIron RX(config)# enable port-config-password BigIron RX(config)# enable read-only-password
  • Dell PowerConnect B-RX4 | Installation Guide - Page 114
    interface - Out of band In band In band In band This section describes the following: • BigIron RX Series support of sub-net masks • How to assign an IP address to a management interface • How to assign to the new active management module port. 102 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 115
    configuration level of the CLI by entering the following command: BigIron RX# configure terminal BigIron RX(config)# Privileged EXEC Level Global CONFIG Level 4. Configure the IP on each interface, virtual interface, and loopback interface. BigIron RX Installation Guide 103 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 116
    interface 1/1, do the following. 1. At the opening CLI prompt, enter enable. BigIron RX> enable 2. Enter the following command at the Privileged EXEC level prompt, then press Enter level of the CLI: BigIron RX(config-if-mgmt-1)# disable 104 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 117
    level. Connecting a BigIron RX Series switch You can connect a BigIron RX Series switch to another 10 Gigabit Ethernet network device. The BigIron RX Series switch supports connections to other vendors' 50/125 micron multimode fiber (2000 Mhz km) BigIron RX Installation Guide 105 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 118
    as well as cleaning the fiber optic connectors and troubleshooting network connections. Installing a fiber optic module You connect a BigIron RX Series switch to another network device using a from the port on the interface module's control panel. 106 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 119
    will only support newly RX(config-mif-e10000-1/1-1/2)# optical-monitor Syntax: [no] optical-monitor The optional variable sets the interval in minutes between which alarms or messages are sent. The default interval is three minutes. BigIron RX Installation Guide
  • Dell PowerConnect B-RX4 | Installation Guide - Page 120
    that you want to monitor optical information from. Cleaning fiber optic modules To avoid problems with the connection between the fiber optic module port and the fiber cable connector, port connector, make sure to keep the protective covering on. 108 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 121
    Connecting a BigIron RX Series switch 4 Troubleshooting network connections After you cable the fiber Web management interface or IronView Network Manager. If a problem persists after taking these actions, contact Brocade's technical support. BigIron RX Installation Guide 109 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 122
    • If the other procedures do not resolve the problem, try using a different port or a different cable. Pinging an IP address To verify that a BigIron RX Series switch can reach another device through the network, up to three responses by default. 110 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 123
    Testing network connectivity 4 Refer to the BigIron RX Series Configuration Guide for information about the command syntax. Using virtual cable testing to diagnose a cable BigIron RX devices support Virtual Cable Test (VCT) technology. VCT technology enables you to diagnose a conductor (wire or
  • Dell PowerConnect B-RX4 | Installation Guide - Page 124
    is detected in the cable • Open: An opening is detected in the cable • ImpedMis: The impedance is mismatched • Failed: The TDR test failed 112 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 125
    MAC address entries 135 Managing the BigIron RX Series chassis DANGER The procedures in this manual are for qualified service personnel. This chapter contains information about of these modules • The MAC address of the BigIron RX Series chassis BigIron RX Installation Guide 113 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 126
    this information, enter the following command at any level of the CLI: BigIron RX# show chassis *** BigIron RX-4 CHASSIS *** ---POWERS --AC Powers Are Used. Power 1: Installed (OK) number> Information about fans in the BigIron RX Series chassis. 114 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 127
    the Syslog configuration and static and dynamic buffers For information about configuring Syslog, refer to the BigIron RX Series Configuration Guide To display the Syslog parameters currently in effect on a BigIron RX Series switch, enter the following command from any level of the CLI: BigIron
  • Dell PowerConnect B-RX4 | Installation Guide - Page 128
    new ones. The static and dynamic buffers are both displayed when you display the log. BigIron RX(config)# show logging ... Static Log Buffer: Aug 27 12:42:42:A:Power Supply 6, 1st the Privileged EXEC level: BigIron RX# clear logging dynamic-buffer 116 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 129
    deg. Low, 77 deg. High, 85 deg. The low and high temperature thresholds enable the BigIron RX Series system to determine at which speed the fans should operate. In general, the fans operate as follows the temperature polling interval" on page 121.) BigIron RX Installation Guide 117 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 130
    medium fan speed for the management modules to 56 C and 72 C, respectively, enter the following command at the global CONFIG level of the CLI: BigIron RX(config)# fan-threshold mp med 56 72 118 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 131
    the low temperature threshold being entered for the high speed (77× C) is higher than the high temperature threshold (76× C) for the medium-high speed. BigIron RX(config)# fan-threshold mp med-hi 67 76 BigIron RX(config)# fan-threshold mp hi 77 85 BigIron RX Installation Guide 119 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 132
    , you can enter the following command at any level of the CLI: BigIron RX# show fan-threshold === Thermal Sensor Control Block (THERMAL_SENSOR_TEST_RULE_MP) === Fan Speed Low shut_off_count = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Syntax: show fan-threshold 120 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 133
    -fan-speed command in the Privileged EXEC level of the CLI allows you to manually set the speed of the fans. For example, to set the speed of fan 0 to medium-high, enter the following command: BigIron RX(config)# set-fan-speed med-hi Syntax: set-fan-speed For the
  • Dell PowerConnect B-RX4 | Installation Guide - Page 134
    can monitor the following aspects of the BigIron RX Series cooling system: • The temperature of RX Series chassis. To display this information the following command at any level of the CLI: BigIron RX# show chassis ... --- FANS --Right Fan Tray: Fan have configured the BigIron RX Series system to use a Syslog
  • Dell PowerConnect B-RX4 | Installation Guide - Page 135
    command at any CLI level: BigIron RX# show log Syntax: show log related events occur: • The BigIron RX Series system synchronizes or prompts you code flash, by default, the BigIron RX Series system synchronizes or prompts you to bootup. When the BigIron RX Series system synchronizes the IronWare
  • Dell PowerConnect B-RX4 | Installation Guide - Page 136
    these situations. Synchronizing the interface modules' IronWare images during bootup By default, the BigIron RX Series system checks the IronWare images in the interface module's flash memory during boot ' IronWare images during bootup" on page 124. 124 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 137
    of the IronWare images during bootup, enter the following command at the global CONFIG level: BigIron RX(config)# no lp disable-lp-sync-check Syntax: no lp disable-lp-sync-check Changing the boot the default or configured boot source one time only. BigIron RX Installation Guide 125 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 138
    1 - 16 for BigIron RX-16. Specifying an immediate boot from a TFTP server For example, to specify an immediate boot for the interface module installed in slot 1 from a TFTP server, enter the following command at the Privileged EXEC level of the CLI: 126 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 139
    module's PCMCIA slot 1, enter the following command at the global CONFIG level of the CLI: BigIron RX(config)# lp boot system slot1 primary all Syntax: lp boot system slot1 | slot2 all the image from which to boot the interface modules. BigIron RX Installation Guide 127 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 140
    interface modules from a TFTP server, enter the following command at the global CONFIG level of the CLI: BigIron RX(config)# lp boot system tftp 123.123.123.123 primary all Syntax: lp boot system tftp
  • Dell PowerConnect B-RX4 | Installation Guide - Page 141
    , the chassis slots will likely lose power because of their low priority. In this scenario for an BigIron RX-8 chassis, slot 8 will lose power first, then slot 7, slot 6, and so on until slot 1 priority or each chassis slot to a different priority. BigIron RX Installation Guide 129 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 142
    module in chassis slot 1, enter the following command at the Privileged EXEC level of the CLI: BigIron RX# power-on lp 1 Syntax: power-on lp The parameter indicates the power-off command, the data in transit is lost. 130 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 143
    usage averaging calculations, enter the following command at the global CONFIG level of the CLI: BigIron RX(config)# cpu-usage on Syntax: cpu-usage on To disable the performance of the usage can affect the performance of the management module. BigIron RX Installation Guide 131 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 144
    so, enter the following command at any level of the CLI: BigIron RX# show tasks Task Name Pri State PC Stack Size CPU Usage(%) task percent. The total may not include resources used by the management processes. A problem could exist If the CPU usage is distributed unevenly to one task, other
  • Dell PowerConnect B-RX4 | Installation Guide - Page 145
    BigIron RX Series of the CLI: BigIron RX(config)# packet-logging 1 BigIron RX-4, 1 - 8 for BigIron RX-8 or 1 - 16 for BigIron RX-16 level of the CLI: BigIron RX(config)# packet-logging 1 BigIron RX-4, 1 - 8 for BigIron RX-8 or 1 - 16 for BigIron RX-16 of the CLI: BigIron RX(config)# packet-logging
  • Dell PowerConnect B-RX4 | Installation Guide - Page 146
    , enter the following command at any CLI level: BigIron RX# show packet-logging 1 memory ..Total 31 packet records 010100e0 52ea1f00 01010102 5204ab10 RX (Assist Header 0x0 you can specify 1 - 4 for BigIron RX-4, 1 - 8 for BigIron RX-8 or 1 - 16 for BigIron RX-16. The memory | flash pktlog.txt
  • Dell PowerConnect B-RX4 | Installation Guide - Page 147
    .cb80.00d in all VLANs, enter the following command at the Privileged EXEC level of the CLI: BigIron RX# clear mac-address 000d.cb80.00d0 Syntax: clear mac-address | ethernet / remove all MAC addresses for a specified VLAN. BigIron RX Installation Guide 135 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 148
    5 Removing MAC address entries 136 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 149
    DANGER The procedures in this manual are for qualified service personnel. This chapter provides a recommended hardware maintenance schedule for a BigIron RX Series switch. Procedures on ) has been removed before inserting a module in the same slot. BigIron RX Installation Guide 137 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 150
    large flat-head screwdriver. Follow the steps given below to remove a management module from the BigIron RX Series chassis. 1. Put on the ESD wrist strap and ground yourself by inserting the plug into an uncovered slot, the system may overheat. 138 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 151
    only. If you attempt to install a BigIron RX Series interface module in another Brocade chassis or an interface module intended for another Brocade chassis in the BigIron RX Series chassis, the chassis and interface module may not function properly. BigIron RX Installation Guide 139 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 152
    of the CLI. For the parameter, specify 1 - 4 for BigIron RX-4, 1 - 8 for BigIron RX-8 or 1 - 16 for BigIron RX-16. 2. Put on the ESD wrist strap and ground yourself by inserting the plug with an uncovered slot, the system may overheat. 140 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 153
    the steps given below to install a new interface module in the BigIron RX Series chassis 1. Put on the ESD wrist strap and ground yourself by inserting the module into the chassis slot, and slide the card along the card guide until the ejectors on either side of the module move close to the module
  • Dell PowerConnect B-RX4 | Installation Guide - Page 154
    an interface module BigIron RX# power-off lp BigIron RX# power-on lp FIGURE 73 Installing a module in a BigIron RX-4 chassis 1 1 Interface module FIGURE 74 Installing a module in a BigIron RX-8 chassis 1 1 Interface module 142 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 155
    Brocade chassis or a switch fabric module intended for another Brocade chassis in a BigIron RX Series chassis, the chassis and switch fabric module will not function properly. CAUTION If a switch fabric module • Installing a new switch fabric module BigIron RX Installation Guide 143 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 156
    it from the BigIron RX Series chassis by following the instructions below. Before removing a switch fabric module from the BigIron RX Series chassis, have RX Series chassis, have the following on hand: • A new switch fabric module, which you can order from Brocade 144 BigIron RX Installation Guide
  • Dell PowerConnect B-RX4 | Installation Guide - Page 157
    its packaging. 3. Insert the module into the chassis slot, and slide the card along the card guide until the ejectors on either side of the module move close to the module front panel. 4. initially installed the module • A small flathead screwdriver BigIron RX Installation Guide 145 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 158
    order from Brocade • An ESD wrist strap with a plug for connection to the ESD connector on the BigIron RX Series chassis DANGER For safety reasons, the ESD wrist strap should contain a 1 meg ohm series resistor. Follow refer to Table 16 on page 109. 146 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 159
    are hot swappable, which means they can be removed and replaced while the BigIron RX Series chassis is powered on and running. However, Brocade recommends that you disconnect the power supply from its power source before removing and replacing the BigIron RX Installation Guide 147 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 160
    forward until the power supply is pulled from its connection to the backplane. 4. In the BigIron RX-8, BigIron RX-16, pull up on the plunger in front of the face plate and pull on the handle toward its position in the chassis. Refer to Figure 76 148 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 161
    Replacing a power supply 6 FIGURE 76 Removing and replacing a BigIron RX-32 power supply 2 3 AC OK DC OK ALM 4 1 into the empty power supply slot, using the guides provided on either side of the slot. CAUTION Carefully follow the mechanical guides on each side of the power supply slot and
  • Dell PowerConnect B-RX4 | Installation Guide - Page 162
    BigIron RX-32 BigIron RX-4, troubleshooting this problem, refer to Table 13 on page 81. Replacing cooling system components The BigIron RX RX- 32" on page 150 • "Replacing fan assemblies in the BigIron RX-16" on page 153 • "Replacing the fan assembly in the BigIron RX-4 and BigIron RX RX RX RX-32
  • Dell PowerConnect B-RX4 | Installation Guide - Page 163
    in Figure 78. Pulling the fan assembly unseats the fan connector from a chassis connector. DANGER The BigIron RX-32 fan assembly is heavy and will be off-balance as you remove it. Use both hands on the . The fan may still be spinning at a high speed. BigIron RX Installation Guide 151 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 164
    6 Replacing cooling system components FIGURE 77 Removing a BigIron RX-32 fan assembly 2 1 4 3 6 5 8 7 10 9 1 Fan module 1 2 Fan module 2 3 Fan module 3 4 Fan module 4 5 Fan module 5 6 Fan module 6 7 change to green when the fan comes up to speed. 152 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 165
    chassis command to verify that the fan is operating normally. Replacing fan assemblies in the BigIron RX-16 The BigIron RX-16 has three fan assemblies: one accessible from the front of the chassis and two may still be spinning at a high speed. BigIron RX Installation Guide 153 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 166
    chassis command to verify that both fans are operating normally. Replacing the front fan assembly in the BigIron RX-16 Follow the steps given below to replace a fan. 1. Put on the ESD wrist strap and secure the fan assembly to the chassis front. 154 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 167
    fan may still be spinning at a high speed. FIGURE 79 Removing a BigIron RX-16 front fan assembly 1 1 Fan assembly 4. Insert the new fan assembly normally. Replacing the fan assembly in the BigIron RX-4 and BigIron RX-8 The BigIron RX-4 and BigIron RX-8 have a fan assembly accessible from the front
  • Dell PowerConnect B-RX4 | Installation Guide - Page 168
    meg ohm series resistor. Follow the steps given below to replace a fan assembly in the BigIron RX-4 and BigIron RX-8. 1. Put on the ESD wrist strap and ground yourself by inserting the plug into the ESD may still be spinning at a high speed. 156 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 169
    1 2 1 Latch release 2 Fan tray assembly FIGURE 81 Removing a fan from a BigIron RX-8 switch 1 2 1 Latch release 2 Fan tray assembly 4. Insert the new fan assembly into Secure the fan to the chassis by tightening the four captive screws. BigIron RX Installation Guide 157 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 170
    cages. Follow the steps given below to replace the filters. NOTE The air filter for the BigIron RX-32 chassis is marked with a directional arrow to indicate proper alignment for the direction of airflow in be inserted with the arrow pointing down 158 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 171
    unscrewing the four socket head screws with an Allen wrench, as shown in Figure 82. FIGURE 82 BigIron RX-32 air inlet panel Pwr Active Pwr Active 1 1 Pwr Active Pwr Active 1 Captive screws 2. until they are securely attached to the chassis. BigIron RX Installation Guide 159 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 172
    RX-32 1 Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active Pwr Active 1 Direction of airflow in chassis Replacing the air filter in the BigIron RX -16 Follow the steps given below to replace the air filter in the BigIron RX-16. 1. Loosen the
  • Dell PowerConnect B-RX4 | Installation Guide - Page 173
    -4 or BigIron RX-8 Follow the steps given below to replace the air filter in the BigIron RX-4 or BigIron RX-8. 1. Loosen the two screws in the front of the filter retainer. 2. Pull the filter retainer away from the chassis as shown in Figure 85 or Figure 86. BigIron RX Installation Guide 161 53
  • Dell PowerConnect B-RX4 | Installation Guide - Page 174
    out of the chassis and discard. 4. Insert the replacement air filter by sliding it along the metal guides. The filter is marked with an arrow. The arrow indicates how the filter should be installed in regards the chassis and tighten the two screws. 162 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 175
    a BigIron RX Series switch and how to load them on the switch. The images required are described in Table 24. DANGER The procedures in this manual are for qualified service personnel TABLE release and are available in the relevant release notes. BigIron RX Installation Guide 163 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 176
    describes each of the software images required to operate a BigIron RX Series switch as described in Table 24. Also, Figure 87 illustrates is packaged with the Monitor image, contains initialization instructions for the hardware startup. Boot images are named as described in Table 24. 164
  • Dell PowerConnect B-RX4 | Installation Guide - Page 177
    on BigIron RX Series switches. A indicates the module type: • If the value of A is m, the image supports a management module. • If the value of A is l, the image supports an interface r, the image contains IronWare management application software. BigIron RX Installation Guide 165 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 178
    an optional field; it indicates the patch release, for example, c. Release number To be supported, a BigIron RX Series chassis must have a software version number x that is consistent across hardware modules at 23:08:32 labeled as rlb02500 166 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 179
    labeled as rmb02500 Line Card Slot 1 Code Flash: Type MT28F640J3, Size 16 MB o IronWare Image (Primary) Version 2.5.0T157, Size 2000853 bytes, Check Sum 1e45 BigIron RX Installation Guide 167 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 180
    2.5.0T155, Size 285248 bytes, Check Sum 5643 Compiled on Oct 19 2007 at 23:08:32 labeled as rlb02500 All show flash done 168 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 181
    . The actual image name depends on the version of software you have running on your BigIron RX Series switch. The output displays the following information about the image: • Version - "2.3.0Txxy" The date and time that Brocade compiled the image. BigIron RX Installation Guide 169 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 182
    contents of the image change, the check sum changes also. • Compilation date and time - The date and time that Brocade compiled the image. 170 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 183
    2 FE 4: Type fe200, Version 2 FE 5: Type fe200, Version 2 FE 6: Type fe200, Version 2 RX-BI-32-SFM Switch Fabric Module 2 (Serial #: PR40060026, Part #: Not Exist) SBRIDGE Version: 6, CPLD 2 FE 4: Type fe200, Version 2 FE 5: Type fe200, Version 2 BigIron RX Installation Guide 171 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 184
    Code Flash (MT28F128J3) 512 MB DRAM Active Management uptime is 20 hours 53 minutes 45 seconds SL M2: RX-BI-32-MR Management Module Standby (Serial #: Not Exist, Part #: Not E xist): Boot : on Oct 19 2007 at 23:09:14 labeled as rmb02500 172 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 185
    20 hours 53 minutes 45 seconds SL 1: RX-BI-24F 24-port 1 GbE Module (Serial 1 uptime is 20 hours 53 minutes 45 seconds SL 15: RX-BI-48T 48-port 1 GbE mini-RJ21 Telco Module (Serial 15 uptime is 20 hours 53 minutes 45 seconds SL 32: RX-BI-24C 24-port 1 GbE Copper Module (Serial #:
  • Dell PowerConnect B-RX4 | Installation Guide - Page 186
    procedures can be different. Follow the procedures described in the following sections: • "Special instructions for using interface modules in a 32-Slot chassis" • "For interface modules running versions 02.5.00 (or later) to a pre-02.5.00 version" 174 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 187
    RX Series software 7 Special instructions for using interface modules in a 32-Slot chassis The BigIron RX-32 chassis introduced with this release can use interface modules in the BigIron RX series that have older versions of the Multi-Service RX system. To avoid this problem, you supporting
  • Dell PowerConnect B-RX4 | Installation Guide - Page 188
    183. Command change Beginning with version 02.5.00 and later of the Multi-Service IronWare software, the copy tftp image command has been changed to enable the one for BigIron RX-16/8/4 (mbridge18.xsvf) and one for the BigIron RX-32(mbridge32.xsvf). 176 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 189
    the mp-boot from a TFTP server at IP address 10.10.12.12, use the following command. BigIron RX#copy tftp image 10.10.12.12 rx02500.bin lp-boot mp-boot Syntax: copy tftp image
  • Dell PowerConnect B-RX4 | Installation Guide - Page 190
    Example BigIron RX rxxxxxx.bin RX to copy the MBRIDGE image. It will now include two MBRIDGES; one for BigIron RX-16/8/4 (mbridge21.xsvf) and one for the BigIron RX .5.00 BigIron RX software release use the following command. BigIron RX#copy tftp image 10.10.12 Example BigIron RX rxxxxxx.bin
  • Dell PowerConnect B-RX4 | Installation Guide - Page 191
    . The source from which to copy the new image is usually a TFTP server to which the BigIron RX Series system has access or a PCMCIA flash card inserted in the management module's slot 1 or 2. to "Rebooting the management module" on page 183. BigIron RX Installation Guide 179 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 192
    RX and boot images on a TFTP server to which the BigIron RX Series system has access or on a PCMCIA flash card inserted RX Series. Enter one of the following commands at the Privileged EXEC level of the CLI (example: BigIron RX#): to which the BigIron RX Series system has access or on a PCMCIA flash
  • Dell PowerConnect B-RX4 | Installation Guide - Page 193
    images simultaneously. 1. Place the new monitor and boot images on a TFTP server to which the BigIron RX Series system has access or on a PCMCIA flash card inserted in slot 1 or 2. 2. Copy the new Privileged EXEC level of the CLI: • show flash BigIron RX Installation Guide 181 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 194
    module in a specified chassis slot. 1. Place the new IronWare image on a TFTP server to which the BigIron RX Series system has access or on a PCMCIA flash card inserted in slot 1 or 2. 2. Copy the new "Rebooting the management module" on page 183. 182 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 195
    RX primary-0 or lp-secondary-0. By default, the BigIron RX Series system checks the interface modules' IronWare images, MBRIDGE FPGA on the management module BigIron RX Series management modules contain an upgradable version you are running on the BigIron RX Series. Refer to the Software Release
  • Dell PowerConnect B-RX4 | Installation Guide - Page 196
    destination. The source from which to copy the new image is usually a TFTP server to which the BigIron RX Series system has access or a flash card in the management module's slot 1 or 2. The destination to has MBRIDGE Revision: 12 installed. 184 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 197
    2 OS upgrade Version 02.3.00a and later of the Multi-Service IronWare software support hitless upgrade of the operating system on a BigIron RX switch. The hitless OS upgrade is designed to allow for that do not exist in the lower release). BigIron RX Installation Guide 185 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 198
    Upgrading the BigIron RX Series software Using this feature, you can upgrade the Multi-Service IronWare software without a loss of service or disruption in the following supported functions and protocols: by the management module switchover feature. 186 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 199
    RX-32 only. It is supported on all other BigIron RX devices. The hitless OS software process Follow the steps given below to perform hitless upgrade of Multi-Service IronWare software. 1. Version 02.3.00 or later of the Multi-Service now the standby. BigIron RX Installation Guide 187 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 200
    RX 02.3.00 or later of the Multi-Service IronWare software to the primary and secondary the active management module. Loading the Multi-Service IronWare software onto the router Hitless Layer 2 the active and standby management modules. For instructions for copying these files, refer to "Upgrading
  • Dell PowerConnect B-RX4 | Installation Guide - Page 201
    the original management module to be active, you must manually fail-over control to it. Executing the hitless upgrade command To files For easy configuration management, the BigIron RX Series switch supports both the download and upload of configuration RX Installation Guide 189 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 202
    command prompt: BigIron RX# write memory Replacing of the CLI: BigIron RX# reload When the system startup-config file You can configure a BigIron RX Series to generate a Syslog message when the a configuration file from the server to a BigIron RX Series, the file is always copied as "startup-
  • Dell PowerConnect B-RX4 | Installation Guide - Page 203
    copy of startup-config from the BigIron RX Series to a TFTP server. • of the running configuration from the BigIron RX Series to a TFTP server. • BigIron RX Series in the CLI: BigIron RX# cp startup-config startup- level in the CLI: BigIron RX# cp startup-config /slot2 the BigIron RX Series switch's
  • Dell PowerConnect B-RX4 | Installation Guide - Page 204
    , and the configuration file contains a command to disable STP on one of the secondary ports in the trunk group, the CLI rejects the 192 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 205
    command to add an address to 3/1, so the CLI responds like this: BigIron RX(config)# interface ethernet 3/1 BigIron RX(config-if-e1000-3/1)# ip add 10.10.10.69/24 Error: can only assign > [overwrite] • ncopy tftp running-config BigIron RX Installation Guide 193 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 206
    third-party SNMP management application such as HP OpenView to save and load a BigIron RX Series switch's configuration. Follow the steps given below to save and load configuration information a TFTP server into the Brocade device's running-config. 194 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 207
    comparison) the standby module's system-config file with its own. • Running-config - The running-config file resides in the BigIron RX Series system memory. The BigIron RX Series switches allow you to do the following related to file synchronization: • Compare files on the active module with files
  • Dell PowerConnect B-RX4 | Installation Guide - Page 208
    the primary or secondary IronWare image in its code flash, by default, the BigIron RX Series system synchronizes or prompts you to synchronize the interface modules IronWare images between the to synchronize the IronWare images during bootup. 196 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 209
    - 16. Disabling or re-enabling an automatic check and synchronization By default, the BigIron RX Series checks the IronWare images in the interface module's flash memory during bootup to ensure it modules IronWare images during bootup" on page 197. BigIron RX Installation Guide 197 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 210
    level: BigIron RX(config)# lp CONFIG level: BigIron RX(config)# no lp reloading the BigIron RX Series system manually, you can you can set the device clock manually. Reloading at a specific time EXEC level of the CLI: BigIron RX# reload at 06:00:00 01-19 RX# reload after 01:12:00 secondary Syntax: reload
  • Dell PowerConnect B-RX4 | Installation Guide - Page 211
    A flash error occurred during the download. Retry the download. If it fails again, contact customer support TFTP failed because of a time out. Check IP connectivity and make sure the TFTP server is to remove unneeded information, then try again. BigIron RX Installation Guide 199 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 212
    the correct image. The TFTP configuration has an error. The specific error message describes the error. Correct the error, then retry the transfer. 200 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 213
    for the BigIron RX Series chassis. TABLE 31 Maximum power calculations @ 100 VAC BigIron RX Series chassis Current Amps Watts BTU per hour BigIron RX-4 12 BigIron RX-8 24 BigIron RX-16 49 BigIron RX-32 N/A 1217 2417 4905 N/A 4155 8249 16741 N/A BigIron RX Installation Guide 201 53
  • Dell PowerConnect B-RX4 | Installation Guide - Page 214
    38746 TABLE 33 Maximum power calculations at 48 VDC BigIron RX Series chassis Amps Watts BigIron RX-4 25 BigIron RX-8 50 BigIron RX-16 102 BigIron RX-32 N/A 1217 2417 4905 N/A BTUs per hour 4155 Interface 191W 110W 101W 102W 210W 245W 202 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 215
    kg (561 lbs) * * 362 lbs (164 kg) for a chassis loaded with blanks, with no power supplies, management modules, switch fabric modules, nor interface modules. BigIron RX Installation Guide 203 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 216
    EN 60825-1 Safety of Laser Products - Part 1: Equipment Classification, Requirements and User's Guide • EN 60825-2 Safety of Laser Products - Part 2: Safety of Optical Fibre A) • VCCI (Japan) (Class A) • EN 61000-3-2 • EN 61000-3-3 • EN 61000-6-1 204 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 217
    cable with either a DB-9 or DB-25 connector, male or female. Serial cable options between the BigIron RX Series chassis and a PC or terminal are shown in Figure 91. NOTE As indicated in Figure 90 you might get unexpected results with some terminals. BigIron RX Installation Guide 205 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 218
    + 2 TD- 3 RD+ 4 Not used (10BaseT) CMT (100BaseTX) 5 Not used (10BaseT) CMT (100BaseTX) 6 RD- 7 Not used (10BaseT) CMT (100BaseTX) 8 Not used (10BaseT) CMT (100BaseTX) 206 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 219
    and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. BigIron RX Installation Guide 207 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 220
    sellers or users should be aware of this. If it is sold or purchased incorrectly, it should be exchanged with a home apparatus (Class B). 208 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 221
    este manual. CAUTION VORSICHT MISE EN GARDE PRECAUCIÓN All devices with DC power supplies (BigIron RX-4, -8, and -16) are intended for installation in restricted access areas only. A restricted access area is where access can be gained only by service RX Installation Guide 209 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 222
    à sertir doit pouvoir être raccordé aux deux vis de mise à la terre du châssis. Pour les BigIron RX-8 et BigIron RX-4, utiliser un câble de mise à la terre de calibre AWG 6 (13 mm²) au minimum. Pour la borne cord can be used safely with the device. 210 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 223
    marqués VW-1 et classés 90 degrés Celsius. Para el circuito de entrada de CC al sistema (BigIron RX-4, -8, y -16), verifique que existe un cortacircuitos catalogado de 30 amperios, como mínimo, -48 VCC . for Category 5 (RJ-45) and fiber-optic cables. BigIron RX Installation Guide 211 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 224
    dépasser 40 C (104 F). No instale el instrumento en un entorno en el que la temperatura ambiente de operación pueda exceder los 40 C (104 F). 212 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 225
    keine Werkzeuge im Chassis zurück. Ne laissez jamais d'outils à l'intérieur du châssis. No deje nunca herramientas en el interior del chasis. BigIron RX Installation Guide 213 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 226
    startup-config. Removal of BigIron RX-32 rear fan modules allows rückwärtigen BigIron RX-32 Ventilatormodule wird der de ventilation en face arrière du BigIron RX-32 permet d'accéder à la distribution los módulos del ventilador trasero del sistema BigIron RX-32 permite el acceso a las barras del bus
  • Dell PowerConnect B-RX4 | Installation Guide - Page 227
    time. Es darf nur ein Ventilatorblech zur Zeit entfernt werden, um ein Überhitzen des BigIron RX-16 und -32 chassis Gehäuses zu vermeiden. Es dürfen nicht beide Ventilatorbleche auf einmal descubierta, el sistema sufrirá sobrecalentamiento. BigIron RX Installation Guide 215 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 228
    service personnel through the use of a special tool, lock and key, or other means of security. Alle Geräte mit Wechselstromquellen (BigIron RX or death. The following are the Danger notices used in this manual. "Gefahr" weist auf eine mögliche Gefährdung hin, die RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 229
    se dan las Peligros utilizadas en este manual. Danger notice Gefahr Danger Peligro The procedures in this manual are for qualified service personnel. Die Installation und Entfernung der Einheit puede ser utilizado con seguridad con el instrumento. BigIron RX Installation Guide 217 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 230
    dass das Gestell oder der Schrank nicht wackeln oder umfallen kann. Vérifiez que le bâti ou le support abritant le dispositif est bien fixé afin qu'il ne devienne pas instable ou qu'il ne ESD deberá contener un resistor en serie de 1 mega ohmio. 218 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 231
    avant d'enlever ou de remplacer le bloc d'alimentation. Le châssis BigIron RX-4, BigIron RX-8 ou BigIron RX-16 peut fonctionner pendant le retrait et le remplacement d'une alimentation électrique, interfaces de fibra óptica utilizan láser de clase 1. BigIron RX Installation Guide 219 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 232
    populated BigIron RX-4, -8, or BigIron RX-4, -8, or RX-4, BigIron RX-8 ou BigIron RX Un chasis BigIron RX-4, -8, ó RX-32 chassis into the rack. The BigIron RX -32 fan assembly is heavy and will be off-balance as you remove it. Use both hands on the handle. Die BigIron RX du BigIron RX-32 est
  • Dell PowerConnect B-RX4 | Installation Guide - Page 233
    the fan or power supply handles. These handles were not designed to support the weight of the chassis. Alle Geräte mit Wechselstromquellen sind du ventilateur ou de l'alimentation. Ces poignées n'ont pas été conçues pour supporter le poids du châssis. Para prevenir daños al chasis y a los
  • Dell PowerConnect B-RX4 | Installation Guide - Page 234
    le rack le châssis vidé de ses éléments. No trate de levantar un chasis BigIron RX-32 totalmente poblado. Es extremadamente pesado. QUITE PRIMERO LOS MÓDULOS DE INTERFAZ Y DE ALIMENTACIÓN ( estar situados en el mismo edificio que la unidad. 222 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 235
    802.3z 1000BaseSX, 1000BaseLX • 802.3x Flow Control RFC support The following sections list the RFCs supported by the BigIron RX Series switch. General protocols • 791 - Internet Protocol ( of subnets • 950 - Internet standard subnetting procedure BigIron RX Installation Guide 223 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 236
    C RFC support • 951 - Bootstrap Protocol (BootP) • 1027 - Proxy ARP • 1042 - IP datagrams over IEEE 802 networks (for Ethernet) • 1122 and version2 MIB • 2154 - OSPF with Digital Signatures (Password, MD-5) • 2178 - Open shortest Path First (OSPF) 224 BigIron RX Installation Guide 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 237
    RFC support C • 2328 - Open Shortest Path First (OSPF) version 2 • 2370 - OSPF Opaque LSA Option RIP • 1058 - Routing Information Protocol (RIP) the User Datagram Protocol using SMIv2 • 2030 - Simple Network Time Protocol (SNTP) • 2068 - HTTP BigIron RX Installation Guide 225 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 238
    Base (MIB) for the Simple Network Management Protocol (SNMP) Internet drafts In addition to the RFCs listed in "RFC support" on page 223, the BigIron RX Series switch supports the following Internet drafts: • ietf-idmr-dvmrp version 3.05, obsoletes RFC 1075 • draft-ietf-pim-dm-05 (V1) • draft
  • Dell PowerConnect B-RX4 | Installation Guide - Page 239
    • The TACACS+ Protocol version 1.78 Internet drafts C BigIron RX Installation Guide 227 53-1001811-01
  • Dell PowerConnect B-RX4 | Installation Guide - Page 240
    C Internet drafts 228 BigIron RX Installation Guide 53-1001811-01
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
53-1001811-01
January 31, 2010
53-1001811-01
*53-1001811-01*
BigIron RX
Installation Guide
Supporting BigIron RX running software release 02.7.02