Dell PowerVault 200S Dell PowerVault 20xS Storage System Documentation Up
Dell PowerVault 200S Manual
View all Dell PowerVault 200S manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerVault 200S manual content summary:
- Dell PowerVault 200S | Dell PowerVault 20xS Storage System Documentation
Up - Page 1
updates your Dell PowerVault 20xS Storage System Installation and Service Guide. 5DFN.LW&RQWHQWV The rack kit includes the following items: Two support Eight flat metal washers Eight square alignment washers NOTE: Some parts may be preinstalled. ,QVWDOOLQJWKH5DLO$VVHPEOLHVLQWKH5DFN :$51 - Dell PowerVault 200S | Dell PowerVault 20xS Storage System Documentation
Up - Page 2
-head screws, as shown in Figure 1. Do not tighten the screws at this time. If the two rail mounting flanges are already attached to the support rails, ensure that the two 10-32 x 1/2-inch Phillips-head screws are slightly loose, allowing the flanges to slide freely - Dell PowerVault 200S | Dell PowerVault 20xS Storage System Documentation
Up - Page 3
adjustable rail mounting flange (see Figure 3). Tighten the two screws. 6. Tighten the two 10-32 screws that hold the adjustable rail mounting flange to the support rail. 7. Repeat steps 3 through 6 to install the second - Dell PowerVault 200S | Dell PowerVault 20xS Storage System Documentation
Up - Page 4
in the U.S.A. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Computer Corporation. Other trademarks and trade names may be used in this
™
P/N 1914P
January 1999
±²³²´&±
www.dell.com
’HOO±²3RZHU9DXOW±²³´[6²6WRUDJH²
6\VWHP²’RFXPHQWDWLRQ²8SGDWH
The following information updates your
Dell PowerVault 20xS Storage System
Installation and Service Guide
.
5DFN².LW²&RQWHQWV
The rack kit includes the following items:
µ
Two support rails
µ
Two adjustable rail mounting flanges
µ
Two mounting ears, usually preinstalled if you ordered a rack-mounted system
µ
Twelve 10-32 x 1/2-inch Phillips pan-head screws
µ
Four 6-32 x 3/8-inch Phillips flat-head screws, usually preinstalled if you ordered a
rack-mounted system
µ
Eight flat metal washers
µ
Eight square alignment washers
NOTE: Some parts may be preinstalled.
,QVWDOOLQJ²WKH²5DLO²$VVHPEOLHV²LQ²WKH²5DFN
:$51,1*±²,I²\RX²DUH²LQVWDOOLQJ²PRUH²WKDQ²RQH²VWRUDJH²V\VWHP³²LQVWDOO²WKH²
ILUVW²VWRUDJH²V\VWHP²LQ²WKH²ORZHVW²SRVLWLRQ²WR²KHOS²SUHYHQW²WKH²UDFN²IURP²
WLSSLQJ²DQG²LQMXULQJ²VRPHRQH²ZKHQ²WKH²VWRUDJH²V\VWHP²LV²SXOOHG²RXW²RI²WKH²
UDFN²RQ²WKH²UDLO²DVVHPEOLHV´²
To install the rail assemblies in the rack, perform the following steps:
1.
Ensure that there is enough room in the rack to install the storage system. The
height of the storage system is 3Us (U = 1 3/4 inches).