Dell PowerVault NX3500 Administrator's Guide - Page 145
If you get disconnected, to view the progress, log in to the CLI again
View all Dell PowerVault NX3500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 145 highlights
This command saves the system configuration on the USB disk-on-key. 2 Transfer the disk-on-key to the new controller, and let it run until the message "ready to be attached/clusterized" (after it configures the network) is displayed. NOTE: Do not remove the USB key until the reconfiguration has occurred. 3 Log in to the CLI on the management IP address and run the following command: system maintenance controllers attach start 4 If you get disconnected, to view the progress, log in to the CLI again and execute the following command: system maintenance controllers attach status This process takes some time to complete. Maintaining the PowerVault NX3500 145
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
Maintaining the PowerVault NX3500
145
This command saves the system configuration on the USB disk-on-key.
2
Transfer the disk-on-key to the new controller, and let it run until the
message "ready to be attached/clusterized" (after it configures the network)
is displayed.
NOTE:
Do not remove the USB key until the reconfiguration has occurred.
3
Log in to the CLI on the management IP address and run the following
command:
system maintenance controllers attach start
<
controllerID
>
4
If you get disconnected, to view the progress, log in to the CLI again and
execute the following command:
system maintenance controllers attach status
This process takes some time to complete.