Dell S5148F-ON EMC PowerSwitch Installation Guide July 2021
Dell S5148F-ON Manual
 |
View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell S5148F-ON manual content summary:
- Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 1
Dell EMC PowerSwitch S5148F-ON Installation Guide July 2021 July 2021 Rev. A04 - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 2
and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2017 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 3
Contents Chapter 1: About this guide...5 Related documents...5 Information symbols...6 Chapter 2: S5148F-ON switch...7 Introduction...7 Features...8 Physical dimensions...8 LED display...8 LED behavior...9 Prerequisites...11 S5148F-ON switch configurations...11 Luggage tag...12 Chapter 3: Site - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 4
ONIE service EMC directive conformance statement 41 Japan VCCI compliance for class A equipment...42 Korean certification of compliance...42 Safety standards and compliance agency certifications 43 Electromagnetic compatibility ...43 Product recycling and disposal...43 Chapter 10: Dell EMC support - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 5
S5148F-ON switch, see the following documents: ● OS10 Enterprise Edition User Guide ● OS10 Enterprise Edition Release Notes ● S5148F-ON Set-up Guide ● S5148F-ON Release Notes ● Open Networking Hardware Diagnostic Guide NOTE: For the most recent documentation, see the Dell EMC support site: www.dell - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 6
about hardware handling that could result in injury. NOTE: The ESD Warning icon requires that you take electrostatic precautions when handling the device. 6 About this guide - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 7
The following sections describe the Dell EMC S5148F-ON switch: Topics: • Introduction • Features • Physical dimensions • LED display • Prerequisites • S5148F-ON switch configurations • Luggage tag Introduction The S5148F-ON switch is a one rack unit, full-featured, fixed form-factor top-of-rack - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 8
port 5. Fan Modules 3 and 4 7. USB Type A 9. RS-232 console port 2. Fan Modules 1 and 2 4. Luggage Tag 6. PSU2 8. MicroUSB-B Port Features The S5148F-ON switch offers the following features: ● Forty-eight 10GbE and 25GbE SFP28 ports ● Six 40GbE and 100GbE QSFP28 ports ● One MicroUSB-B console port - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 9
1. Stack ID LED 3. Port Activity LED 5. System LED 7. Fan LED 9. RJ-45 Ethernet Port LED: Left is activity; right is link. Table 1. S5148F-ON switch LED behavior LED System Status/Health LED Power LED 2. Port Activity LED 4. Master LED 6. Locator LED 8. Power LED Description ● Solid green-Normal - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 10
Table 1. S5148F-ON switch LED behavior (continued) LED Description ● Blinking yellow-Power supply failed Master LED ● Off-Switch is in Stacking Slave mode ● Solid green-Switch is in Stacking Master or Standalone mode FAN LED ● Off-No power ● Solid green-Normal operation; fan powered and - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 11
are: ● M3 or M4 ground cable screw, depending on your switch ● Extra mounting brackets ● Extra power supply unit ● Extra fan module S5148F-ON switch configurations You can order the S5148F-ON switch in several different configurations: ● S5148F-ON AC or DC Normal Airflow: fifty-four 10/25/40/50 - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 12
the luggage tag includes a QRL that takes you to a How-To site where you can watch videos about racking the switch, replacing components, configuring port channels, and so on. Figure 4. S5148F-ON switch luggage tag 1. Service tag 3. PPID 2. MAC address 4. Express service code 12 S5148F-ON switch - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 13
applies For more information about switch specifications, see Specifications. NOTE: Install the S5148F-ON switch in a rack or cabinet components Site selection Install the switch equipment in restricted access areas. A restricted access area is one in which service personnel can only gain access - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 14
point the power service in your area uses. The ground path must be permanent. Fans and airflow The S5148F-ON switch fans support two airflow options: as part of the factory install based on stock keeping unit (SKU) type. The S5148F-ON switch has SKUs that support the following configurations: ● AC or - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 15
. NEBS-compliant ground installation Before you install the switch into a rack, install the ground (GND) lug assembly. Your switch includes an assembled UL-certified GND lug with bracket, packaged separately. If any parts are missing, contact your Dell EMC Sales Representative. NEBS compliance 15 - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 16
surfaces thoroughly and apply an anti-oxidant solution to the mating surfaces. 4. Attach the switch ground using the Ground cable instructions. 5. Using the two removed screws, attach the GND lug bracket assembly to your switch, as shown. Torque the M3 screws to ±4-5 in-lbs. Figure 6. Attach the GND - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 17
Figure 7. GND lug assembly attached 6. Install your switch into your rack using the S5148F-ON switch installation instructions. NEBS compliance 17 - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 18
an ESD-preventive wrist or heel ground strap when handling the S5148F-ON switch and components. As with all electrical devices of this type, WARNING: This document is a condensed reference. Read the safety instructions in your Safety, Environmental, and Regulatory information booklet before you - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 19
panel facing downward. ReadyRails installation To easily configure your rack for installation of your S5148F-ON switch, use the ReadyRails rack mounting system provided. out of the outside rail. NOTE: For more installation instructions, see the installation labels attached to the rail assembly. - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 20
Two-post flush-mount installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. CAUTION: Your switch is not NEBS Earthquake Z4-compliant if you this installation method. 1. For this configuration, remove the castings from the front side of each - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 21
Figure 10. Two-post flush-mount configuration 2. Attach one rail to the front post flange with two post center-mount installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. CAUTION: Your switch is not NEBS Earthquake Z4-compliant if you this - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 22
for the second rail. Four-post threaded installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. CAUTION: To be the two screws from each front latch on the switch side of the rail. Remove the tool-less latch casting. Retain the castings - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 23
in the same manner as the four-post configurations. 1U front-rack installation Configure the rails that are attached to the switch. NOTE: For more instructions, see the installation instruction labels on the rail. 1. Attach the inner switch rails to the S5148F-ON switch. Line up the rail with the - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 24
and slide the switch in until it is flush with front of rack. To keep the switch from inadvertently sliding out of the rack and falling, about 3 inches before you fully insert your switch, the rail locking feature engages. Figure 14. Front rack installation 24 S5148F-ON switch installation - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 25
two M4 screws. In both configurations, the ground cable is not included. To properly ground the switch, Dell EMC recommends a one- or two- S5148F-ON switch has SFP28 and QSFP28 optical ports. For a list of supported optics, see the specification sheets at www.dell.com/support or contact your Dell EMC - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 26
. The fan speed slows as the switch continues to boot up. After switch placement After you have securely installed and powered on the S5148F-ON switch, for more information: ● If you are using Dell EMC software, see switch documentation at www.dell.com/support/. ● If you need ONIE information, see - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 27
the procedure included with the firmware download. 7. Copy the backed-up switch configuration to the new switch. copy tftp://hostip/filepath running-config 8. Install the new switch in your rack or cabinet. For detailed installation instructions, see S5148F-ON switch installation. If you are using - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 28
• AC or DC power supply installation • DC power supply to power source connection Components The following power supply options are available for the S5148F-ON switch: ● AC or DC power supply with integrated fan ● AC or DC power supply with integrated reverse flow fan Power supply 1 (PSU1) is on - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 29
supply, install the power supply in the first slot, PSU1. Install a blank plate in the second slot, PSU2. 1. Remove the PSU slot cover from the S5148F-ON switch using a small #1 Phillips screwdriver. 2. Remove the PSU from the electro-static bag. 3. Insert the PSU into the - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 30
into a slot as this action may damage the PSU or the S5148F-ON switch. NOTE: If a PSU fails, you must replace the entire unit. There are no field serviceable components in the PSU. To request a hardware replacement, see Dell EMC support. NOTE: If you use a single PSU, install a blank plate in the - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 31
WARNING: Do not cross the wires. In the wiring block, RTN aligns with RTN and -48V aligns with -48V. 5. Insert the DC power connector into the power socket of the DC PSU. Ensure that the connector pins firmly seat and you hear the click of the power connector's left and right levered clamps lock - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 32
factory with two PSUs and four fan modules installed in the switch. The fan modules and the power supplies, which have integrated fans, are hot-swappable. In addition to the power supply modules, you can order and install fan modules separately. The S5148F-ON switch supports in a configuration must - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 33
the S5148F-ON switch are field replaceable. Module slot 1 is on the left side of the switch; module slot 4 is on the right side of the switch. CAUTION Dell EMC support. CAUTION: Complete the following steps within one minute or the switch temperature could rise above safe thresholds and the switch - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 34
2. Unlatch and remove the first module that needs the filter replaced. 3. Slide the existing filter upwards to remove it from the module. 4. Replace the filter with a new filter of the same size. 5. Reinsert the fan module. 6. Repeat for the remaining modules that need the filter replaced. 34 Fans - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 35
-B console port access • USB storage mount • Before you install an OS • ONIE service discovery RS-232 console port access The RS-232 console port is on the PSU-side of the S5148F-ON switch. Figure 20. S5148F-ON switch RS-232 console and management ports 1. Out-of-band network management port (top - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 36
console port is on the PSU side of the switch. NOTE: The S5148F-ON switch uses the Silicon Labs CP2109 USB-B chip. To ● No flow control USB storage mount USB storage does not automatically mount. USB storage supports the FAT file system. To use USB storage, first mount the device using the - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 37
to the console, ONIE:. NOTE: For more information, see the Open Networking Hardware Diagnostic Guide. NOTE: After you have securely installed and powered on the S5148F-ON switch, to configure your switch, see your third-party ONIE-compatible OS or the Dell EMC OS documentation. Management ports 37 - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 38
the ONIE Service Discovery methods are successful, you can disable this using the onie-discovery-stop command. You can install an operating system manually from HTTP, FTP, or TFTP using the onie-nos-install command. NOTE: If you have a recovery USB plugged into your switch, - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 39
lists the S5148F-ON switch specifications. CAUTION of the batteries according to the manufacturer's instructions. NOTE: For RoHS information, see Commission statement • European Union EMC directive conformance statement • Japan Depth Chassis weight with factory-installed components Rack clearance - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 40
BTU/Hr 10,000 feet (3,048 meters) 39,370 feet (12,000 meters) Dell EMC Spec SV0115 Specifications 100-240 VAC 50/60 Hz 4.7A/3.9A at 100/120V AC 2. 5V/24.0A −48V/19.2A −60V/ 16.0A, with fan IEEE standards The S5148F-ON switch complies with the following IEEE standards. ● 802.1ab (LLDP) ● 802.1ax ( - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 41
The S5148F-ON switch is designed it is not installed and used in accordance to the instructions, it may cause harmful interference to radio communications. Operation of must be used in order to meet FCC emission limits. Dell EMC is not responsible for any radio or television interference caused by - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 42
is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. NOTE: Use the AC power cords with Dell EMC equipment only. Do not use Dell EMC AC power cords with any unauthorized hardware. Figure 23. Japan: warning - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 43
and User's Guide ● EN 60825 switch according to applicable local and national regulations. Dell EMC encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Dell EMC offers a variety of product return programs and services - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 44
recycle and reuse of IT and telecommunications products Dell EMC switches are labeled in accordance with European Directive 2002 information on Dell EMC product recycling offerings, see the WEEE Recycling instructions on Support. For more information, contact the Dell EMC Technical Assistance Center - Dell S5148F-ON | EMC PowerSwitch Installation Guide July 2021 - Page 45
Us. On the Contact Information web page, click Technical Support. To access switch documentation, go to www.dell.com/manuals/. To search for drivers and downloads, go to www.dell.com/drivers/. To participate in Dell EMC community blogs and forums, go to www.dell.com/community. Dell EMC support 45
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
 |
 |
Dell EMC PowerSwitch S5148F-ON
Installation Guide
July 2021
July 2021
Rev. A04