Dell S5148F-ON EMC PowerSwitch Set-up Guide
Dell S5148F-ON Manual
 |
View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell S5148F-ON manual content summary:
- Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 1
Dell EMC PowerSwitch S5148F-ON Set-up Guide March 2021 Rev. A01 - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 2
and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2017 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 3
...12 Four-post threaded installation...13 S5148F-ON installation...14 1U front-rack installation...14 Optics installation...16 Optics removal...16 Switch power-up...16 After switch installation...17 Chapter 4: Specifications...18 Chassis physical design...18 Chapter 5: Support...20 Contents 3 - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 4
Notes ● OS10 Enterprise Edition User Guide ● Installation Guide for the S5148F-ON Switch ● Open Networking Hardware Diagnostic Guide ● Dell EMC S5148F-ON Switch Release Notes NOTE: For the most recent documentation, visit the support site: www.dell.com/support. Information Symbols This book uses - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 5
NOTE: The ESD Warning icon requires that you take electrostatic precautions when handling the device. About this guide 5 - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 6
For more information about the S5148F-ON switch specifications, see Specifications. NOTE: Install the switch into a rack or Switch ground • Fans and airflow • Power • Storing components Site selection Install your equipment in restricted access areas. A restricted access area is one where service - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 7
be permanent. Switch ground Dell EMC recommends grounding your switch. Use the S5148F-ON switch in a CBN. Fans and airflow Fan installation is done as part of the factory install based on stock keeping unit (SKU) type. The S5148F-ON switch has SKUs that support the following configurations: ● AC PSU - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 8
are included: ● One S5148F-ON switch ● One RJ-45 to DB-9 female cable ● Two sets of rail kits, no tools required ● Two PSUs ● Four fan units ● Two country- and region-specific AC power cords ● S5148F-ON Set-up Guide ● Safety and Regulatory Information ● Warranty and Support Information 1. Place the - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 9
WARNING: This guide is a condensed reference. Read the safety instructions in your position. ReadyRails installation To easily configure your rack for switch installation, use the ReadyRails rack instructions, see the installation labels attached to the rail assembly. S5148F-ON switch Installation 9 - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 10
Figure 2. Separate rails 1U Tool-less mount installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. 1. Face the ReadyRails flange ears show how the pegs appear in both the square and nonthreaded round holes. 10 S5148F-ON switch Installation - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 11
on each flange ear and unseat each rail. Two-post flush-mount installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. 1. For this configuration, remove the latch castings from the front side of each ReadyRails assembly, item 1. To remove the - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 12
with two user-supplied screws, item 3. 4. Repeat this procedure for the second rail. Two-post center-mount installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. 1. Slide the plunger bracket rearward until it clicks into place and secure the - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 13
with two user-supplied screws, items 2 and 3. 3. Repeat this procedure for the second rail. Four-post threaded installation NOTE: For more installation instructions, see the installation labels attached to the rail assembly. 1. Remove the latch castings from each end of the ReadyRails assemblies. To - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 14
the same manner as the four-post configurations. 1U front-rack installation Configure the rails that are attached to the switch. 1. NOTE: For more information, see the installation instruction labels on the rail. Attach the inner switch rails to the S5148F-ON switch. Line up the rail with the - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 15
the ReadyRails. Slide the switch in until it is flush with the front of rack. About three inches before you fully insert your switch, the rail locking feature engages to keep the switch from inadvertently sliding out and falling. Figure 8. Front rack installation S5148F-ON switch Installation 15 - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 16
power-up Supply power to the S5148F-ON switch after you mount it in a rack or cabinet. Reinspect your switch before power up. Verify the following: ● The equipment is properly secured to the rack. Dell EMC recommends properly grounding the switch. ● The ambient temperature around the unit, which - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 17
After switch installation To configure your switch, after you have securely installed and powered on the S5148F-ON switch, see your open network installation environment (ONIE)-compatible operating system documentation at www.onie.org. S5148F-ON switch Installation 17 - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 18
Specifications This section lists the S5148F-ON switch specifications. CAUTION: Operate the product Dispose of the batteries according to the manufacturer's instructions. NOTE: For RoHS information, see Restricted Material Depth Chassis weight with factory-installed components Rack clearance - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 19
voltage range Input current at full load with fan Specifications 470 W = 1603.7 BTU/Hr 10,000 feet (3,048 meters) 39,370 feet (12,000 meters) Dell EMC Spec SV0115 Specifications 100-240 VAC 50/60 Hz 4.7A/3.9A at 100/120V AC 2.35A/1.95A at 200/240V AC 470 Watts 200 Watts Specifications - Dell S5148F-ON | EMC PowerSwitch Set-up Guide - Page 20
tag or express service code, pull out the tag or enter the show chassis command from the CLI. ● To receive more technical support, click Contact Us. On the Contact Information web page, click Technical Support. To access switch documentation, go to www.dell.com/manuals/. To search for drivers
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
Dell EMC PowerSwitch S5148F-ON
Set-up Guide
March 2021
Rev. A01