Dell Unity XT 680 WEEE Disassembly Instructions BPE12BPE25
Dell Unity XT 680 Manual
 |
View all Dell Unity XT 680 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Unity XT 680 manual content summary:
- Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 1
WEEE DISASSEMBLY INSTRUCTIONS for the BPE12 and BPE25 DPE Disk Processor Enclosure Abstract This Waste Electrical and Electronic Equipment (WEEE) directive. The document does not replace disposal instructions in EMC contracts, or those included in EMC Product and Residuals Disposal Guidelines. April - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 2
Copyright © 2014 EMC Corporation. All Rights Reserved. EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice. The information in this publication is provided "as is." EMC Corporation makes no representations or - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 3
Table of Contents 1.0 Document Purpose...5 2.0 Important Notice ...5 3.0 How to Use these Instructions 5 4.0 Related Documentation ...5 5.0 Brand Owner Identification 5 6.0 Acronyms...6 7.0 Product Identification ...8 7.1 BPE12 Disk Processor Enclosure 8 7.2 BPE25 Disk Processor Enclosure 8 8.0 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 4
11.3 Plastic Part Markings ...35 12.0 Disassembling the DPE...36 12.1 Prerequisites ...36 12.1.1 Required Tools for Disassembly 36 12.1.2 Safety Precautions and Battery Warnings 36 12.2 Disassembly Sequence...37 12.3 Removing a Disk ...38 12.3.1 Disassembling a 3.5" Disk 38 12.3.2 Disassembling a - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 5
platform. Contact the EMC WEEE administrator at [email protected] to request additional documentation as required. WEEE Reuse and Treatment Instructions for EMC Product Consoles and Bezels 5.0 Brand Owner Identification EMC Corporation 176 South Street Hopkinton, Massachusetts 01748 U.S.A http://www - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 6
6.0 Acronyms Table 1 defines acronyms that may be used in the document. Table 1. Acronyms List ABS Ag Au BBU Cd CFC CPU Cr Vl Cu DAE DIMMs DPE DRL EMI ESD EU GWP HC HCFC HDPE Hg LCC LDPE Pb PBB PBDE PC PCB PCT Pd PETE or PET Acrylonitrile butadiene styrene Silver Gold Battery Backup Unit Cadmium - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 7
PP PS Pt PVC RoHS SAS SP SPE SSD V WEEE Polypropylene Polystyrene Platinum Polyvinyl Chloride Restriction of Hazardous Substances Serial Attached SCSI Storage Processor Storage Processor Enclosure Solid State Disk Volt Waste Electrical and Electronic Equipment 7 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 8
BPE25 2U 25 disk DPE, Disk Processor Enclosure 100-542-440-xx Note: The part number cited denotes the base chassis. However, each platform supports many different EMC products. Contact your EMC Sales Representative for product-specific part numbers. 22.0 kg (48.5 lb) Height: 8.65 cm (3.4 in) Width - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 9
8.0 Product Photos and Illustrations Components with reportable items are referred to consistently using a yellow blocked item number. Sub-components are identified by appending that number with a letter. These references are also used in the reportable materials tables. See: 11.0 Reportable - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 10
8.1.2 BPE12 Photos- Front/Back Labeled 5A Figure 3. Front image of BPE12 2 3 1A 5A Figure 4. Rear image of BPE12 4 10 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 11
8.2 BPE25 This section includes labelled illustrations and photos for the disk processor enclosure that contains 25 2.5" disks. 8.2.1 BPE25 Illustrations- Front/Back Labeled Figure 5. BPE25 Front view 5B 23 1B Figure 6. Back view 4 Table 5. BPE25 Main components with reportable items Item - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 12
8.2.2 BPE25 Photos- Front/Back Labeled 5B Figure 7. Front image of BPE25 2 3 1B 5B Figure 8. Rear image of BPE25 4 12 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 13
8.3 Disks Disk type is dependent on specific DPE type: BPE12: contains 3.5" disks BPE25: contains 2.5" disks 8.3.1 3.5" Disk 1A Figure 9. 3.5" Disk 8.3.2 2.5" Disk 1B Figure 10. 2.5" Disk 13 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 14
8.4 Fan Module 2 Figure 11. Fan module 8.5 Power Supply 3 Figure 12. Power Supply 8.6 Storage Processor (SP) 4 Figure 13. Storage processor 14 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 15
8.7 Chassis The chassis differs slightly between the BPE12 and BPE25. Key differences are: • Depth dimension • Midplanes • Disk cage architecture 8.7.1 BPE12 Chassis 5A Figure 14. BPE12 chassis 8.7.2 BPE25 Chassis 5B Figure 15. BPE25 chassis 15 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 16
9.0 Locating Materials Each of the main components may have subcomponents that have specific reportable items. In that case, a lower case letter is appended to the main component number. Refer to Table 6. Table 6. Component/sub-component ID table Item # 1A Item Description 3.5" Disk See: 9.1.1, - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 17
4 Storage Processor (SP) 4a SP PCB See: 9.4 Locating Materials on a Storage Processor (SP) on page 23 4b I/O module PCB 4c BBU 4c.1 BBU PCB 4c.2 BBU chassis, black plastic PC+ABS, 33 grams 4c.3 BBU lithium-ion batteries, (3), 12V 4d I/O module bracket, ferrous metal 4e SP latch knobs, - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 18
5B BPE25 Chassis 5B1 Midplane PCB, TUC 872, Hbr See: 9.5.2 BPE25 Chassis- material locations on page 26 5B2 Sub-PCBs (2/chassis) 5B3 Enclosure chassis, metal, ferrous 5B4 Midplane chassis panel, metal, ferrous 5B5 Midplane chassis, metal, ferrous 5B6 5B7 5B8 5B9 5B10 5B11 Serial Number tag - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 19
9.1 Locating Materials on a Disk Disk type is dependent on specific DPE type: BPE12: contains 12 3.5" disks: Component 1A BPE25: contains 25 2.5" disks: Component 1B Note: Disassembly procedures for the OEM disk drives are the responsibility of the manufacturer. 9.1.1 3.5" disk- material - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 20
9.1.2 2.5" disk- material locations To remove this component, see: 12.3 Removing a Disk on page 38. 1B.4 1B.3 1B.1 Figure 18. 2.5" disk material locations Table 8. List of 2.5" disk components Item 1B.1 Description PCB, SAS, 2.5" disk 1B.2 Hard Disk Drive carrier, metal, ferrous 1B.2 Item - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 21
9.2 Locating Materials on a Fan Module To remove this component, see: 12.4 Removing a Fan Module on page 42. 2e 2a 2b 2d 2c Figure 19. Fan module components Table 9. List of cooling module components Item Component 2a PCB, fan module 2b PCB bracket, black plastic, PC+ABS-FR(40) - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 22
9.3 Locating Materials on a Power Supply To remove this component, see 12.5 Removing a Power Supply on page 45. 3b 3c 3f 3d 3a 3c 3e Figure 20. Power supply components Table 10. List of power supply components Item Component 3a PCB, PSU 3b Electrolytic Capacitor 3c Copper wire - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 23
9.4 Locating Materials on a Storage Processor (SP) To remove this component, see: 12.6 Removing a Storage Processor (SP) on page 48. Alpha-numerical references to components are listed in Table 11 List of SP components on page 24. 4k 4i 4j 4e 4b 4d 4e Figure 21. SP-components 4f 4c 4c.2 4a - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 24
Table 11. List of SP components Item Component 4a PCB, storage processor 4b PCB, I/O module (optional, may be blank) 4c BBU 4c.1 PCB, BBU 4c.2 BBU chassis, black plastic PC+ABS, 33 grams 4c.3 BBU lithium-ion batteries, (3), 12V 4d I/O module bracket, metal, ferrous 4e SP latch knobs, terracotta - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 25
9.5 Locating Materials on a Chassis The chassis differs slightly between the BPE12 and BPE25. Key differences are depth, midplane chassis assembly and PCBs, and the disk cage. See: 12.7.1 BPE12 Disassembly on page 57. 9.5.1 BPE12 Chassis- material locations 5A4 5A3 5A9 5A5 5A2 Figure 22. - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 26
9.5.2 BPE25 Chassis- material locations The midplane chassis assembly has been extracted and is shown below. 5B4 5B3 5B8 5B9 5B12 5B6 5B7 Figure 23. BPE25 chassis components 5B2 5B1 Table 13. List of BPE25 chassis components Item Component 5B1 PCB, midplane, TUC 872, Hbr 5B2 PCBs, sub- - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 27
9.6 Accessories and Optional Equipment Table 14 lists accessories and optional equipment. Table 14. Accessories and Options Component AC Power Cord Photo DC Power Cord Disassembly Required? No See Table 16 to identify materials. No See Table 16 to identify materials. 27 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 28
10.0 DPE PCBs The following PCBs may be located within the system. Some variation may exist depending on system configuration. Table 15. PCBs within the system Disk PCB 1A1 3.5" disk PCB 1B1 2.5" disk PCB Fan Module PCB 2a Power Supply Module PCB 3a 28 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 29
Storage Processor PCBs 4a I/O Module PCB 4b BBU Module PCB 4c.1 29 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 30
Chassis Midplane PCBs 5A1 5B1 Chassis PCBs, sub-midplane (2 per chassis) 5A2 5B2 Note: Both chassis types use the same sub-midplane PCBs. Ambient Sensor PCBs 5A9 5B12 30 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 31
11.0 Reportable Materials Table 16 lists components that require selective treatment. To locate specific items, refer the tables and images in 8.0 Product Photos and 9.0 Locating Materials. Table 16. Complete list of Reportable Materials Material Item Polychlorinated biphenyl (PCB) containing - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 32
Material Gas discharge lamps Liquid crystal displays (together with their casing where appropriate) of a surface greater than 100 cm2 and all those back-lighted with gas discharge lamps External electric cables Item See Table 14 Embedded electric cables Components containing radioactive - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 33
11.1 Materials of Interest to Recyclers Table 17 lists materials for recycling. To locate specific items, refer the tables and images in 8.0 Product Photos and 9.0 Locating Materials. Table 17. Complete list of Recyclable Materials Material Non-ferrous Alloys Ferrous Alloys ABS Item 3c 4i 4j 1A4 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 34
Material Polyethylene Terephthalate (PETE or PET) High-Density Polyethylene (HDPE) Polyvinyl Chloride (PVC) Low-Density Polyethylene (LDPE) Polypropylene (PP) Polystyrene (PS) Other plastics, (e.g. acrylic; polycarbonate; nylon; fiberglass) Item Location 5B6 Serial Number tag (2 per chassis) - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 35
11.2 Precious Metals Table 18 lists precious metals for recovery. To locate specific items, refer the tables and images in 8.0 Product Photos and 9.0 Locating Materials. Table 18. Precious Metals Material Copper (Cu) Gold (Au) Palladium (Pd) Platinum (Pt) Silver (Ag) Item 3c 1A1 1B.1 2a 3a 4a 4b - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 36
or components with batteries are processed in a shredder. - Replace only with the battery type recommended by the equipment manufacturer. - Discard used batteries according to manufacturer's instructions. - Do not attempt to reuse or install batteries in any other system, for any other purpose. 36 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 37
12.2 Disassembly Sequence Follow the sequence listed below when disassembling this system. You can also use the table as a checklist Table 21. Disassembly sequence and checklist Step Component Removal Procedure Component Disassembly Procedure 12.3.1 Disassembling a 3.5" Disk on page 38 1 12.3 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 38
12.3 Removing a Disk Use the instructions in the table below based on the disk size in your system. To remove a 3.5" disk: To remove a 2.5" disk: 1. Press the orange tab in and pull - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 39
Figure 24. Screw locations 2. Push up on the side of the carrier opposite of the SAS PCB and after it clears the disk chassis, push it laterally until the SAS PCB disconnects from the chassis connector. Figure 25. Separating the carrier from the disk chassis 3. Lift the carrier off the chassis. - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 40
4. To separate the SAS PCB from the carrier, move the two plastic tabs on each end of the PCB inward, and then pull the PCB free from the carrier. Figure 27. Location of one of the PCB tabs Figure 28. PCB separated from carrier Note: Disassembly procedures for the OEM disk drives are the - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 41
12.3.2 Disassembling a 2.5" Disk See 9.1.2 2.5" disk- material locations on page 20 to identify the subcomponents within the disk. 1. Using a small flathead screwdriver, pry open the plastic latch of the disk enclosure. Figure 29. Dislodging the plastic latch 2. Separate the two long sides of the - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 42
12.4 Removing a Fan Module 1. Pinch the two orange tabs on the sides of the fan module together to release it from the chassis. 2. Pull the fan module out of the chassis and place it on a clean static-free work surface Figure 32. Removing a fan module Figure 33. Fan module after extraction 42 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 43
12.4.1 Disassembling a Fan Module See 9.2 Locating Materials on a Fan Module on page 21 to identify the subcomponents within the fan module. 1. Disconnect the fan motors from the PCB. Figure 34. Fan motor - PCB connector 2. Separate the PCB bracket from the fan assembly by squeezing the sides of the - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 44
Figure 37. PCB removed from bracket 4. Remove the fan motor by cutting the rubber fasteners in four (4) places that secure the four corners of the motor to the housing. If necessary clip the fan assembly wires to remove the motor. Figure 38. Location of two of the four fan motor fasteners 44 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 45
12.5 Removing a Power Supply 1. While grasping the power supply's handle, push the supply's orange release tab to the right. 2. Pull the power supply from the enclosure and place it on a clean, static-free surface. Figure 39. Removing a power supply 12.5.1 Disassembling the Power Supply See 9.3 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 46
b. Lift off the top of the power supply housing. Tip: The top cover is hinged; therefore lift and rotate on the hinge. Figure 41. Opening the power supply assembly housing c. Remove top completely and then unfold the black protective covering to allow access to the capacitors and PCB. 2. Use the - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 47
3. Remove the large capacitor (item 4.1b): a. Locate the large capacitor on the power supply PCB. b. Use wire cutters to trim the capacitor leads, and remove the large capacitor. Figure 43. Removing the large capacitor on the power supply 47 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 48
assembly is released from the enclosure. 3. Use the latches to slide the SP assembly about half-way out of the enclosure. 4. Use both hands to support the SP assembly and pull it fully out of the enclosure. 5. Place the SP assembly on a clean, flat static-free work surface. Figure 44. Removing - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 49
12.6.1 Disassembling a Storage Processor (SP) See 9.4 Locating Materials on a Storage Processor (SP) on page 23 to identify the subcomponents within the SP. 1. Remove the mSATA SSD: a. Turn the SP assembly over so that its bottom side faces up. b. Push the latch in on the plastic cover and rotate - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 50
2. Remove the top cover of the SP assembly: a. Press the blue button on the cover. b. Push the cover straight back 1/4 inch. c. Lift the cover up. Figure 47. Removing the SP top cover 3. Remove the memory modules from the SP assembly: a. Press down on both of the memory module latches to release the - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 51
4. Remove the BBU from the SP assembly: a. Press the white tabs on each side of the cable connector while gently pulling upward to release it from the processor board. You may need to gently rock the connector to remove it. b. Push the blue tab to the left to release the BBU, and then carefully pull - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 52
b. Slide the lid to the left until the lid tabs disengage from the metal chassis, and then pull the lid off the top of the BBU. Figure 51. Removing the battery casing from the BBU chassis Figure 52. BBU after lid is removed c. Using a Philips driver, remove the three screws that secure the PCB to - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 53
Figure 54. BBU PCB and batteries after removal from chassis d. Disconnect the three batteries from the BBU PCB using a soldering iron, wire cutters, or a similar tool. Figure 55. Location of BBU battery connections to BBU PCB Figure 56. BBU PCB after battery removal 53 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 54
6. Remove the I/O module from the SP assembly: Note: This component is optional. If a blank module is present, remove it and proceed to step 8. a. Lift the blue latch carefully until it ejects the I/O module from the connector. b. Lift the module out and away from the SP assembly and place it on a - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 55
The SP is now prepared for PCB extraction. Figure 59. SP with all sub-components removed 8. Tip the SP so you have access to the bottom of the SP and using a Philips driver, remove the single screw that secures the SP PCB. Figure 60. Location of PCB securing screw 55 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 56
9. Gently navigate the PCB past the tabs/notches and then laterally out of the SP chassis. Figure 61. Removing the SP PCB Figure 62. SP PCB after extraction from chassis 10. If necessary, remove the heatsinks, CPU, coin-cell battery, and any other board subcomponents. 56 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 57
12.7 Disassembling the Chassis The chassis differs slightly between the BPE12 and BPE25. Key differences are: • Depth dimension • Midplanes • Disk cage architecture 12.7.1 BPE12 Disassembly See 9.5.1 BPE12 Chassis- material locations on page 25 to identify the subcomponents within the BPE12 chassis. - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 58
3. Remove the ten (10) screws that secure the midplane chassis assembly to the main chassis. (3 screws on each side, 4 screws on bottom) Figure 65. Location of midplane chassis assembly- side screws Figure 66. Location of midplane chassis assembly- bottom screws 58 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 59
4. Carefully lift the midplane chassis assembly out of the main chassis. Figure 67. Midplane chassis assembly removed from main chassis 5. Disassemble the midplane chassis assembly: a. Using a Philips driver, remove the 12 screws that secure the two sub-midplane PCBs to the midplane chassis. Figure - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 60
c. Using a Philips driver, remove the four (4) screws that secure the midplane PCB to the midplane chassis. Figure 70. Location of midplane PCB screws d. Pull off the clear plastic protective barrier from the midplane PCB. e. Pull the midplane PCB from the midplane chassis. Figure 71. Midplane PCB - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 61
Ambient sensor PCB Glued to chassis in center disk bay. 5A9 61 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 62
12.7.2 BPE25 Disassembly Before starting this procedure, make sure all subcomponents have been removed from the chassis. See 9.5.2 BPE25 Chassis- material locations on page 26 to identify the subcomponents within the BPE25 chassis. 1. Using a Philips driver, remove the 7 screws that secure the - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 63
3. Remove the ten (10) screws that secure the midplane chassis assembly to the main chassis. (3 screws on each side, 4 screws on bottom) Figure 75. Location of midplane chassis assembly- side screws Figure 76. Location of midplane chassis assembly- bottom screws 63 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 64
4. Carefully lift the midplane assembly out of the chassis. Figure 77. Midplane chassis assembly removed from main chassis 5. Disassemble the midplane chassis: a. Using a Philips driver, remove the 12 screws that secure the two sub-midplane PCBs to the midplane chassis. Figure 78. Location of PCB - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 65
c. Using a Philips driver, remove the 10 screws that secure the midplane PCB to the midplane chassis. Figure 80. Location of midplane PCB screws d. Pull off the clear plastic protective barrier from the midplane PCB. e. Pull the midplane PCB from the midplane chassis. Figure 81. Midplane PCB after - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 66
The chassis is disassembled with the exception of several plastic components. In some instances the components can merely be removed with force. Others are secured with rivots and may require destructive means to remove. These components are listed below in no particular order: Fan baffle (6 per - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 67
Ambient sensor PCB Glued to chassis in center disk bay. 5B12 67 - Dell Unity XT 680 | WEEE Disassembly Instructions BPE12BPE25 - Page 68
13.0 RoHS Restricted Materials Table 22 lists Restriction of Hazardous Substances (RoHS) materials. Table 22 RoHS Materials Material Cadmium (Cd) Hexavalent Chromium (Cr VI) Lead (Pb) Mercury (Hg) Polybrominated Biphenyls (PBB) Polybrominated Diphenyl Ethers (PBDE) Item Location Absent Absent
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
 |
 |
Abstract
This document provides guidance for end-of-life recyclers on how to
identify and disassemble reportable materials in compliance with the
Waste Electrical and Electronic Equipment (WEEE) directive. The document
does not replace disposal instructions in EMC contracts, or those included
in
EMC
Product and Residuals Disposal Guidelines
.
April 2014
WEEE DISASSEMBLY INSTRUCTIONS
for the BPE12 and BPE25 DPE Disk Processor Enclosure