Dell Wyse 5050 All-In-One Wyse PCoIP Firmware Release 5.4.1 Release Notes
Dell Wyse 5050 All-In-One Manual
View all Dell Wyse 5050 All-In-One manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Wyse 5050 All-In-One manual content summary:
- Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 1
supports the following platforms: • Dell Wyse 5030 zero client for VMware and AWS. • Dell Wyse 5050 AIO thin client. • Dell Wyse 7030 zero client for VMware and AWS. Upgrade scenarios 1. Upgrade Teradici firmware using WDM 5.7.1 or 5.7.2. a. To update firmware from 4.x to 5.x. Dell Wyse PCoIP - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 2
Zero Client Firmware 5.0 and later requires PCoIP Connection Manager for Amazon WorkSpaces 1.0.2 GA or later in order to connect to Amazon WorkSpaces. It is not compatible with earlier versions of the PCoIP VMware Horizon ✔ Amazon WorkSpaces ✔ Teradici Cloud Access Platform 2 Dell Wyse - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 3
Connection Broker. NOTE: After upgrading from PCoIP Zero Client Firmware 4.x to 5.x, the session connection type for the zero client must be changed to PCoIP VMware Horizon ✔ ✔ ✔ Amazon WorkSpaces Teradici Cloud Access Platform ✔ Dell Wyse PCoIP Firmware Release 5.4.1 Release Notes 3 - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 4
must support TLS compatible with one major release zero clients on this firmware release to connect to Remote Workstation Cards may require you to use both versions of PCoIP Management Console: VMware Horizon ✔ ✔ Amazon WorkSpaces ✔ Teradici Cloud Access Platform 4 Dell Wyse PCoIP - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 5
Notes Platforms Workstation 5.4.0 5.4.0 5.4.0 5.4.1 version 2 to manage the zero clients, and version 1.x to manage Remote Workstation Cards until such time as there is a Remote Workstation Card firmware release that is supported by PCoIP Management Console 2.0 or higher. This release has been - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 6
: After upgrading from PCoIP zero client firmware 4.x to 5.x, the session connection type for the zero client must be changed to PCoIP Connection Manager, with the address of the VMware Horizon ✔ ✔ ✔ Amazon WorkSpaces ✔ Teradici Cloud Access Platform ✔ 6 Dell Wyse PCoIP Firmware Release - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 7
to the zero client, then restart the PCoIP session and disconnect/reconnect the drive. Manual IPv6 gateway address is overwritten on reset. Although the IPv6 Gateway address is displayed as an editable field on the zero client Administrative Web Interface (AWI), Dell Wyse PCoIP Firmware Release - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 8
a zero client's display port connectors may not show the remote desktop content when the zero client starts a PCoIP session to PCoIP session is reconnected. The message shown is Unable to connect (0x1001). Please contact your IT administrator. This message can be safely ignored. 8 Dell Wyse PCoIP - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 9
pictures The event log might become flooded with messages that began Event log for zero clients no longer flooded with messages with RDMA2 :src_mac if a zero client operated in PoE (Power over Ethernet) mode or was configured to use 802.1x. Dell Wyse PCoIP Firmware Release 5.4.1 Release Notes 9 - Dell Wyse 5050 All-In-One | Wyse PCoIP Firmware Release 5.4.1 Release Notes - Page 10
of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
Dell Wyse PCoIP Firmware Release 5.4.1 Release
Notes
Current Version:
5.4.1
Release Date:
2017-04
Topics:
•
Release overview PColP
•
Supported platforms
•
Upgrade scenarios
•
Upgrade paths
•
Compatibility
•
Known Issues and workaround
•
Fixed issue
Software releases are created to correct defects, make enhancements, or add new features. These releases are tested on all current,
actively shipping platforms and operating systems, as applicable. This release notes contain details on the supported platforms, any
changes in the configuration settings and licensing details as well. The bug fixes along with the workarounds are documented in the
release notes. Any changes in the feature functionality from an end-user perspective are listed with the description of each feature at a
high level.
Release overview PColP
The zero client firmware is applicable for Tera2 zero client only. This document provides a summary of upgrade scenarios, new feature,
compatibility notes, and upgrade paths for Dell Wyse PCoiP firmware release 5.4.1
For WDM:
•
WDM v5.7.2 and v5.7.1 supports 4.x, 5.2.2 and 5.4.1 firmware versions.
•
Earlier versions of WDM support only 4.x. If you are using earlier versions of WDM, then upgrade the WDM to version 5.7.1 and
proceed with the firmware update.
For Teradici console:
•
PColP management console 2.x cannot detect or manage devices on firmware versions earlier than version 5.0. If you need to upgrade
from firmware 4.x, then either the zero client AWI or PColP management console 1.10.3-1.10.7 must be used to upgrade the zero client
to firmware 5.x.
•
Zero clients on firmware 5.x can only be managed by PColP management console 2.0 or later. PColP management console 1.x cannot
detect or manage devices on firmware 5.x.
Supported platforms
This release supports the following platforms:
•
Dell Wyse 5030 zero client for VMware and AWS.
•
Dell Wyse 5050 AIO thin client.
•
Dell Wyse 7030 zero client for VMware and AWS.
Upgrade scenarios
1.
Upgrade Teradici firmware using WDM 5.7.1 or 5.7.2.
a.
To update firmware from 4.x to 5.x.
Rev. A00
2017 - 05
Dell Wyse PCoIP Firmware Release 5.4.1 Release Notes
1