Denon AVR 1707 Owners Manual - English - Page 11

Connections, Speaker impedance - problem

Get Denon AVR 1707 - AV Receiver PDF manuals and user guides
UPC - 081757507127
View all Denon AVR 1707 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Easy Setup Procedure Speaker connections Connect the speaker terminals with the speakers making sure that like polarities are matched (< with with >). NOTE: When making connections, take care that none of the individual conductors of the speaker cable come in contact with adjacent terminals, with other speaker cable conductors, or with the rear panel and screws. NEVER touch the speaker terminals when the power is on. Doing so could result in electric shocks. Connecting the speaker cables 1. Loosen by turning counterclockwise. Either tightly twist or terminate the core wires. 2. Insert the cable. 3. Tighten by turning clockwise. Connecting banana plugs Turn clockwise to tighten, then insert the banana plug. ¢ Speaker impedance Speaker Front A, B Front A+B Center Surround Surround back / ZONE2 Impedance 6 ~ 16 Ω/ohms 12 ~ 16 Ω/ohms 6 ~ 16 Ω/ohms Note on speaker impedance When using speakers with an impedance below the designated value (for example 4 Ω/ohms), playing for long periods of time with the volume high could cause the temperature to rise, activating the protection circuit. When the protection circuit is activated, the output to the speakers is cut off and the power indicator blinks. If this happens, unplug the power cord, wait for the set to cool off and improve ventilation around the unit. Also check the wiring of the input cables and the speaker cables. After doing this, plug the power cord back in and turn the unit's power back on. If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center. ENGLISH Easy Setup Procedure ¢ Connections • With the AVR-1707, up to ten speakers can be connected for surround playback. • When making connections, also refer to the operating instructions of the other components. Subwoofer Connection terminal for subwoofer with built-in amplifier. IN Center speaker >< Surround speakers (L) (R) > < (L) (R) >< Front speakers (B) (L) (R) >< Front speakers (A) (L) (R) > < Surround back speakers When using only one surround back speaker, connect it to the left channel. 8 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
>
<
<
>
>
<
<
>
>
<
>
<
>
<
>
<
>
<
IN
(
L
)
(
R
)
(
L
)
(
R
)
(
L
)
(
R
)
(
L
)
(
R
)
Easy Setup Procedure
Easy Setup Procedure
8
ENGLISH
ENGLISH
¢
Connections
• With the AVR-1707, up to ten speakers can be connected for surround playback.
• When making connections, also refer to the operating instructions of the other components.
When using only one surround back
speaker, connect it to the left channel.
Connection terminal for
subwoofer with built-in
amplifier.
Front speakers
(A)
Surround
speakers
Front speakers
(B)
Subwoofer
Surround back
speakers
Center
speaker
Impedance
Speaker
Connecting the speaker cables
Speaker connections
Connect the speaker terminals with the speakers
making sure that like polarities are matched (
<
with
<
,
>
with
>
).
¢
Speaker impedance
Note on speaker impedance
When using speakers with an impedance
below the designated value (for example 4
Ω
/ohms), playing for long periods of time with
the volume high could cause the temperature
to rise, activating the protection circuit.
When the protection circuit is activated, the
output to the speakers is cut off and the power
indicator blinks. If this happens, unplug the
power cord, wait for the set to cool off and
improve ventilation around the unit. Also check
the wiring of the input cables and the speaker
cables. After doing this, plug the power cord
back in and turn the unit’s power back on.
If the protection circuit is activated again even
though there are no problems with the wiring or
the ventilation around the unit, switch off the
power and contact a DENON service center.
NOTE:
When making connections, take care that
none of the individual conductors of the
speaker cable come in contact with adjacent
terminals,
with
other
speaker
cable
conductors, or with the rear panel and
screws.
NEVER touch the speaker terminals when
the power is on. Doing so could result in
electric shocks.
1.
Loosen by turning
counterclockwise.
Either tightly twist or terminate the core
wires.
2.
Insert the cable.
3.
Tighten by turning clockwise.
6 ~ 16
Ω
/ohms
Center
Surround
Surround back / ZONE2
6 ~ 16
Ω
/ohms
Front A, B
12 ~ 16
Ω
/ohms
Front A+B
Connecting banana plugs
Turn clockwise to tighten, then
insert the banana plug.