Denon AVR 1707 Owners Manual - English - Page 40

Last function memory, Backup memory, Simultaneous recording - factory reset

Get Denon AVR 1707 - AV Receiver PDF manuals and user guides
UPC - 081757507127
View all Denon AVR 1707 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

ENGLISH Advanced Operation INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit Recording the program source (recording the source currently being monitored) 1 Select the input source to be played. 2 Select the input mode and play (surround) mode. 3 Start recording on the tape or video deck. For instructions, refer to the component's operating instructions. Advanced Operation About the memory functions ¢ Last function memory The various settings set when the AVR-1707's power is switched to standby are stored in the memory. When the power is turned back on, the settings made when the power was switched to standby are recalled. ¢ Backup memory The various settings are stored in the memory for about 1 week, even when the power is turned off or the power cord is unplugged. • The AUDIO IN's signal selected with INPUT SELECTOR are output to the CD-R/TAPE and VCR AUDIO OUT terminals. • Digital signals are not output to the audio output terminals. Initialization of the microprocessor (Reset) If the indication on the display is not normal or if the operation of the unit is not correct, then the microprocessor should be reset by the following procedure. ¢ Simultaneous recording The signals of the source selected with INPUT SELECTOR are output simultaneously to the CD-R/TAPE and VCR REC OUT terminals. If a total of two tape and/or video decks are connected and set to the recording mode, the same source can be recorded simultaneously on every decks. 1 Switch off the unit using . 2 Keep both (A and B) depressed and turn on the unit by pressing . 3 Check that the entire display is flashing at 1-second intervals and release the buttons. • The microprocessor will be initialized. • If step 3 does not work, start over from step 1. • If the microprocessor has been reset, all the button settings are reset to the default values (the values set upon shipment from the factory). 37 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ENGLISH
37
ENGLISH
¢
Last function memory
The various settings set when the AVR-1707’s power is switched to
standby are stored in the memory. When the power is turned back on,
the settings made when the power was switched to standby are
recalled.
About the memory functions
Recording the program source (recording the
source currently being monitored)
¢
Backup memory
The various settings are stored in the memory for about 1 week, even
when the power is turned off or the power cord is unplugged.
Advanced Operation
Advanced Operation
Initialization of the microprocessor (Reset)
If the indication on the display is not normal or if the operation of the
unit is not correct, then the microprocessor should be reset by the
following procedure.
Switch off the unit using
<POWER>
.
1
Check that the entire display is flashing at 1-second
intervals and release the buttons.
• The microprocessor will be initialized.
3
Keep both
<SPEAKER>
(
A
and
B
) depressed and turn
on the unit by pressing
<POWER>
.
2
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from the
factory).
Select the input source to be played.
1
Start recording on the tape or video deck.
For instructions, refer to the component’s operating instructions.
3
Select the input mode and play (surround) mode.
2
• The AUDIO IN’s signal selected with
INPUT SELECTOR
are output to
the CD-R/TAPE and VCR AUDIO OUT terminals.
• Digital signals are not output to the audio output terminals.
¢
Simultaneous recording
The signals of the source selected with
INPUT SELECTOR
are output
simultaneously to the CD-R/TAPE and VCR REC OUT terminals. If a
total of two tape and/or video decks are connected and set to the
recording mode, the same source can be recorded simultaneously on
every decks.
About the button names in this explanation
<
>
: Buttons on the main unit
[
]
: Buttons on the remote control unit
Button name only
:
Buttons on the main unit and remote control unit
INPUT SELECTOR
INPUT SELECTOR
INPUT SELECTOR
<SPEAKER>
<POWER>