Denon AVR 1707 Owners Manual - English - Page 50

Enter, Test Tone]

Get Denon AVR 1707 - AV Receiver PDF manuals and user guides
UPC - 081757507127
View all Denon AVR 1707 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

ENGLISH Advanced Setup - Part 2 Advanced Setup - Part 2 Setting the Test Tone 1 • The distance changes in units of 1 foot (0.1 meters) each time the Set the volume of the various speakers so that the sound output from 17 T.TONE Yes< button is pressed. Select the value closest to the measured distance. • Please note that the difference of distance for every speaker the speakers and the subwoofer seems to have the same volume level. 2 T.Tone Auto > should be 20 ft (6.0 m) or less. 1 Press F to select "Yes". 3 TEST TONE ON Setting the Crossover Frequency Set the frequency (Hz) below which the bass sound of the various speakers is to be output from the subwoofer. For speakers that are set to "Small", frequencies under the crossover frequency are cut before the signal is output, and the low frequency component that was cut is output from the subwoofer or the speakers that are set to "Large". 1 Press F G to set. 40, 60, 80, 90, 100, 110, 120, 150, 200, 250 Hz: Set as desired according to your speakers' bass playback ability. 2 Press F G to set, then press H. Auto: Adjust the level while listening to the test tones produced automatically from each speaker. Test tones are automatically emitted from each speaker. Manual: Adjust with the speaker from which the test tone is output switched manually. 3 When "Auto" mode is selected: Press F G to adjust the volume. -1 • Test tones are output automatically, in the order shown below. 2 Press ENTER or H to enter the setting and switch to the Test Tone setting. 1 16Cr.Over 100Hz FL C FR SR (2 speakers) SW SL SBL SBR SB (1 speaker) The volume can be adjusted within the range -12 dB to +12 dB. 2 17 T.Tone Yes< 3 When "Manual" mode is selected: Press D H to select the speaker, then press F G to -2 adjust the volume. • The crossover frequency mode is valid only when subwoofer is set to "ON", and when one or more speakers are set to "Small", as described in section "Setting the Speaker Configuration" ( page 45, 46). • Set to "80 Hz" when using regular speakers. When using small speakers, we recommend setting to a higher frequency. 4 Press ENTER to finish the Test Tone setting. 5 Press ENTER the setting and switch to the Input Setup. A U T O - F L 5 • To adjust the channel level separately for the different play modes after setting the channel level, perform the operation on page 30. ¢ Adjusting the test tone using the remote control unit Adjustment of the test tones using the remote control unit is only possible in the "Auto" mode and only valid in the STANDARD (Dolby Surround and DTS Surround) mode. The adjusted levels are automatically stored for the different surround modes. 1 Press [TEST TONE]. • Test tones are output from the different speakers. 2 Press F G to adjust the volume. 3 Press [TEST TONE]. 47 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1
7
T
.
T
O
N
E
Y
e
s
<
1
ENGLISH
47
ENGLISH
Advanced Setup – Part 2
Advanced Setup – Part 2
Set the volume of the various speakers so that the sound output from
the speakers and the subwoofer seems to have the same volume
level.
Press
FG
to set, then press
H
.
When “Auto” mode is selected:
Press
FG
to adjust the volume.
• Test tones are output automatically, in the order shown below.
Auto:
Adjust the level while listening to the test tones produced
automatically from each speaker.
Test tones are automatically emitted from each speaker.
Manual:
Adjust with the speaker from which the test tone is output
switched manually.
FL
SW
C
FR
SR
SBL
SL
SB
SBR
Setting the Test Tone
The volume can be adjusted within the range –12 dB to +12 dB.
When “Manual” mode is selected:
Press
DH
to select the speaker, then press
FG
to
adjust the volume.
Press
ENTER
to finish the Test Tone setting.
2
3
-1
3
-2
4
(2 speakers)
(1 speaker)
¢
Adjusting the test tone using the remote control
unit
Adjustment of the test tones using the remote control unit is only
possible in the “Auto” mode and only valid in the STANDARD (Dolby
Surround and DTS Surround) mode. The adjusted levels are
automatically stored for the different surround modes.
Press
[TEST TONE]
.
• Test tones are output from the different speakers.
Press
[TEST TONE]
.
Press
FG
to adjust the volume.
1
2
3
• To adjust the channel level separately for the different play modes
after setting the channel level, perform the operation on page 30.
T
.
T
o
n
e
A
u
t
o
>
2
T
E
S
T
T
O
N
E
O
N
3
A
U
T
O
-
F
L
• The distance changes in units of 1 foot (0.1 meters) each time the
button is pressed. Select the value closest to the measured
distance.
•
Please note that the difference of distance for every speaker
should be 20 ft (6.0 m) or less.
Setting the Crossover Frequency
Set the frequency (Hz) below which the bass sound of the various
speakers is to be output from the subwoofer.
For speakers that are set to “Small”, frequencies under the crossover
frequency are cut before the signal is output, and the low frequency
component that was cut is output from the subwoofer or the
speakers that are set to “Large”.
40, 60, 80, 90, 100, 110, 120, 150, 200, 250 Hz:
Set as desired according to your speakers’ bass playback ability.
Press
ENTER
or
H
to enter the setting and switch to
the Test Tone setting.
2
• The crossover frequency mode is valid only when subwoofer is set
to “ON”, and when one or more speakers are set to “Small”, as
described in section “Setting the Speaker Configuration” (
page
45, 46).
• Set to “80 Hz” when using regular speakers. When using small
speakers, we recommend setting to a higher frequency.
Press
FG
to set.
1
1
6
C
r
.
O
v
e
r
1
0
0
H
z
1
1
7
T
.
T
o
n
e
Y
e
s
<
2
Press
F
to select “Yes”.
1
Press
ENTER
the setting and switch to the Input Setup.
5
5