Denon AVR-1912 Owners Manual - Page 21

Error messages - speaker setup

Get Denon AVR-1912 PDF manuals and user guides
UPC - 883795001984
View all Denon AVR-1912 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Basic version Advanced version Information Error messages Set up speakers (Audyssey® Auto Setup) NOTE • An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey® Auto Setup over again. • If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker connections and repeat the measurement process from the beginning. • Be sure to turn off the power before checking speaker connections. Examples Audyssey Auto Setup Caution! Microphone or Speaker is none MultEQ Error details • The connected setup microphone is broken, or a device other than the supplied setup microphone is connected. • Not all speakers could be detected. • The front L speaker was not properly detected. Measures • Connect the included setup microphone to the SETUP MIC jack of this unit. • Check the speaker connections. Retry [ ] Cancel Audyssey Auto Setup MultEQ Caution! Ambient noise is too high or Level is too low Retry [ ] Cancel Audyssey Auto Setup MultEQ Caution! Speaker:None Front R • There is too much noise in the room for accurate measurements to be made. • Speaker or subwoofer sound is too low for accurate measurements to be made. • Either turn off any device generating noise or move it away. • Perform again when the surroundings are quieter. • Check the speaker installation and the direction in which the speakers are facing. • Adjust the subwoofer's volume. • The displayed speaker could not be detected. (The screen on the left indicates that the front right speaker cannot be detected.) • Check the connections of the displayed speaker. Retry Audyssey Auto Setup [ ] Cancel MultEQ Caution! Speaker:Phase Front R Skip Retry [ ] Cancel • The displayed speaker is connected with the polarity reversed. (The screen on the left indicates that the polarity phases of the front right speakers are reversed.) • Check the polarity of the displayed speaker. • For some speakers, this error message may be displayed even if the speaker is properly connected. If you are sure the connection is correct, press ui to select "Skip", then press ENTER. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
18
Error messages
NOTE
•
An error message is displayed if Audyssey
®
Auto Setup could not be completed due to speaker placement, the measurement environment, etc. If this happens, check the relevant items, be sure to take the necessary
measures, then perform Audyssey
®
Auto Setup over again.
•
If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that the speakers are not connected properly. Turn this unit off, check the speaker
connections and repeat the measurement process from the beginning.
•
Be sure to turn off the power before checking speaker connections.
Examples
Error details
Measures
MultEQ
Caution!
Microphone or Speaker is none
Retry
Audyssey Auto Setup
•
The connected setup microphone is broken, or a
device other than the
supplied setup microphone is connected.
•
Not all speakers could be detected.
•
The front L speaker was not properly detected.
•
Connect the included setup microphone to the SETUP MIC jack of this unit.
•
Check the speaker connections.
MultEQ
Caution!
Ambient noise is too high or Level is too low
Retry
Audyssey Auto Setup
•
There is too much noise in the room for accurate measurements to be
made.
•
Speaker or subwoofer sound is too low for accurate measurements to be
made.
•
Either turn off any device generating noise or move it away.
•
Perform again when the surroundings are quieter.
•
Check the speaker installation and the direction in which the speakers are
facing.
•
Adjust the subwoofer’s volume.
MultEQ
Audyssey Auto Setup
Caution! Speaker:None
Front R
Retry
•
The displayed speaker could not be detected.
(The screen on the left indicates that the front right speaker cannot be
detected.)
•
Check the connections of the displayed speaker.
MultEQ
Audyssey Auto Setup
Caution! Speaker:Phase
Front R
Skip
Retry
•
The displayed speaker is connected with the polarity reversed.
(The screen on the left indicates that the polarity phases of the front right
speakers are reversed.)
•
Check the polarity of the displayed speaker.
•
For some speakers, this error message may be
displayed even if the speaker is properly connected.
If you are sure the connection is correct, press
ui
to select “Skip”, then press
ENTER
.
Set up speakers (Audyssey
®
Auto Setup)