Denon AVR1910 Owners Manual - English - Page 25

Getting Started Connections Settings Playback Multi-Zone Remote Control Information Troubleshooting Specifications ENGLISH Changing the amplifier assignment (Amp Assign) The signals output from the AVR-1910's SURR. BACK/AMP ASSIGN speaker terminals can be switched to signals of the surround mode being used. 1 Press ui to select "Amp Assign". Front 2 Press o p to select Amp Assign Mode. 3-1.Audyssey Auto Setup MultEQ Please place microphone at ear height at main listening position. Front Sp.: A Amp Assign: Normal Start Cancel [ENT]:Select [RTN]:Back Normal : The sound of the surround back channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. ZONE2 : If the ZONE2 power is on, the sound of the ZONE2 channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Front A Bi-Amp : The sound of the front A bi-amp channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Front B Bi-Amp : The sound of the front B bi-amp channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. Front Height : The sound of the front height channel is output from the speakers connected to the SURR. BACK/AMP ASSIGN terminals. n To cancel Audyssey Auto Setup Use ui to select "Cancel", then use o p to select "Yes". Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup) Step 3 : Performing the Audyssey Auto Setup Procedure • The Audyssey Auto Setup function detects the presence of each speaker and automatically calculates the speaker size, channel level, distance, and optimal crossover frequency setting. Audyssey MultEQ corrects acoustical distortions within the listening area. • Once started, MultEQ will play a series of test tones through each speaker. • Before starting, connect and position all of your speakers. 1 Press ui to select "Start", then press . Detection of the speaker configuration starts. 3-1.Audyssey Auto Setup MultEQ Please place microphone at ear height at main listening position. Front Sp.: A Amp Assign: Normal Start Cancel [ENT]:Select [RTN]:Back 2 Once all the speakers have been detected and the screen on the right appears, check the results of detection of the connected speakers. Step1:Speaker Detection MultEQ Front Sp. :Yes Center Sp. :Yes Subwoofer :Yes Surround Sp. :Yes S.Back Sp. :Yes :2sp Next Retry [ENT]:Next 3 Once you have checked the results, use ui to select "Next", then press . Measurements for the main listening position begin. 4 Once the screen on the right appears, move the setup microphone to the second position, use ui to select "Next", then press . Step2:Measurement MultEQ Please place microphone at ear height at 2nd listening position. Next Calculate Cancel [ENT]:Next Measurements for the second position begin. 5 Perform Step 4 repeatedly for the 3rd, 4th, 5th, and 6th measurments. Once measurements for the sixth position are completed, "All the measurements were finished." is displayed. b Measure at a total of six positions, including the main listening position and positions around it. It is possible to stop the settings with five positions or fewer, but for better results we recommend measuring at six positions. 6 Once measurements are finished, use ui to select "Calculate", then press . Analysis begins. b Analysis takes several minutes to complete. The time required for this analysis depends on the number of speakers connected. The greater the number of speakers connected, the longer analysis will take. Step2:Measurement MultEQ All the measurements were finished. Calculate Retry Cancel [ENT]:Cancel ⇩ Step3:Calculation MultEQ Calculating Please wait... [----------] 7 Use ui to select the item you want to check, then press . Step4:Check The measurement result MultEQ confirmation screen is Please check the results of the measured item. displayed. b Subwoofers or other speakers may be set to a value that does not correspond to the actual Speaker Config.Check Distance Check Channel Level Check Crossover Freq.Check Next [ENT]:Select distance. See overleaf 22