Denon AVR1910 Owners Manual - English - Page 49
Adjusting the tone Tone Control, Making the MultEQ, Dynamic EQ and Dynamic Volume, settings Audyssey
UPC - 083795000899
View all Denon AVR1910 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 49 highlights
Getting Started Connections Settings Playback Multi-Zone Remote Control Information Troubleshooting Specifications Setting items Setting contents Front Height ON : Use the front height channel. Set whether or not to use OFF : Do not use the front height channel. the front height channel. This can also be set by pressing . Subwoofer ATT ON : The input from the subwoofer channel is attenuated. Attenuate subwoofer level OFF : The input from the subwoofer channel is not attenuated. Usually use when using EXT. IN mode. in this mode. Set this to "ON" if the subwoofer channel level seems too high when playing audio signal. Subwoofer ON : The subwoofer is used. Turn subwoofer output on OFF : The subwoofer is not used. and off. Default Yes : Reset to the defaults. Restores all the surround No : Do not reset to the defaults. parameter settings to their defaults. Adjusting the tone (Tone Control) Default settings are underlined. Setting items Setting contents Tone Control ON : Allow tone adjustment (treble, bass). Sets the tone control function OFF : Playback without tone adjustment. ON and OFF. The tone cannot be adjusted when in the DIRECT mode. This can be set when "Dynamic EQ" (vpage 47) is set to "OFF". Bass -6dB ~ +6dB (0dB) Adjusts the low frequencies. This can be set when "Tone Control" is set to "ON". Treble Adjusts the frequencies. -6dB ~ +6dB (0dB) high This can be set when "Tone Control" is set to "ON". ENGLISH Adjusting the Sound Field Effect (Parameter) Making the MultEQ, Dynamic EQ and Dynamic Volume settings (Audyssey Settings) Default settings are underlined. • When the "Audyssey Auto Setup" (vpage 20) procedure is performed, the "MultEQ", "Dynamic EQ" and "Dynamic Volume" functions are enabled. • Operating conditions for each function • Dynamic EQ : MultEQ When "MultEQ" is set to "ON" • Dynamic Volume : Dynamic EQ When "Dynamic EQ" is set to "ON" • Setting : When "Dynamic Volume" is set to "ON" Dynamic Volume Setting NOTE If the speaker settings are changed after the "Audyssey Auto Setup" procedure is performed, "MultEQ", "Dynamic EQ" and "Dynamic Volume" functions cannot be selected and "Run Audyssey" is displayed. If this happens, either perform the "Audyssey Auto Setup" procedure again, or perform the "Restore" operation (vpage 24) to restore the settings to as they were after the "Audyssey Auto Setup" procedure was performed. Setting items Setting contents MultEQ Audyssey : Optimize frequency response of all speakers. Corrects the frequency Audyssey Byp.L/R : Optimize frequency response of speakers except response of the different front L and R speakers. speakers. Audyssey Flat : Optimize frequency response of all speakers to flat response. NOTE Manual : Apply frequency response set with "Manual EQ" (vpage 47). • "MultEQ" and "Manual OFF : The "MultEQ" equalizer cannot be used. EQ" settings for which "Not Used" has been set at • When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is "EQ Customize" (vpage selected, " " lights. 29) cannot be selected. • W hen using headphones, • After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed "MultEQ" is set to "OFF". without increasing the number of speakers measured, only " " lights. • This can also be set by pressing . Remote control operation buttons Displaying the menu : Cancel the menu : Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menu 46