Denon AVR1910 Owners Manual - English - Page 50

Getting Started Connections Settings Playback Multi-Zone Remote Control Information Troubleshooting Specifications ENGLISH Setting items Setting contents Dynamic EQ ON : Use Dynamic EQ function. Audyssey Dynamic EQ solves OFF : Do not use Dynamic EQ function. the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. • When set to "ON", " " is displayed. • When "MultEQ" is set to "OFF", "Dynamic EQ" is automatically set to "OFF" • This can also be set by pressing . This can be set when the "MultEQ" (vpage 46) is set to anything other than "OFF". Dynamic EQ : ON/Volume : OFF Dynamic EQ / Volume : OFF ""GRreedn"" ""OOFfFf" NOTE "Tone Control" is set to "OFF" when "Dynamic EQ" is set to "ON". Reference Level Offset : Audyssey Dynamic EQ takes the standard film mixing level of 85 dB SPL during -20 dB FS input as its reference level. However, since standardization is lacking outside the film industry, the reference level of media contents may not be appropriate. In order to view such contents, Reference Level Offset of Dynamic EQ has available offsets of 5 dB, 10 dB and 15 dB. • 0dB : Suitable for viewing movies. • 5dB : Suitable for listening to classical music and other content mixed at a high level. • 10dB : Suitable for listening to jazz and other audio sources with a wide dynamic range. Also suitable for viewing TV. • 15dB : Suitable for listening to pop, rock music and other content with an extremely wide dynamic range. Setting is enabled when "Dynamic EQ" is "ON" . Dynamic Volume ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level Audyssey Dynamic Volume of the "Setting" (vpage 47) solves the problem of OFF : Do not use Dynamic Volume. large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. • When set to "ON", " " is displayed. • W hen "MultEQ" is set to "OFF", "Dynamic Volume" is automatically set to "OFF". • This can also be set by pressing . Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF This can be set when "Dynamic EQ" (vpage 47) is set to "ON". ""GGrreeeenn"" "Red" Adjusting the Sound Field Effect (Parameter) Setting items Setting Set Dynamic Volume effect. This can be set when "Dynamic EQ" (vpage 47) is set to "ON". Setting contents Day : Low setting provides the least adjustments to the loudest and softest of sounds. Evening : Middle setting prevents loud and soft sounds from being much louder and softer respectively than average sounds. Midnight : High setting affects volume the most, causing all sounds to be of equal loudness. Adjust tonal quality for each speaker using graphic equalizer (Manual EQ) Default settings are underlined. Setting items Setting contents Adjust CH 1. Select speaker adjustment method. Adjust the tonal quality of All CH : Adjust tonal quality for all speakers together. the individual speakers. L/R CH : Adjust tonal quality for each L/R speaker pair. Each CH : Adjust tonal quality for each speaker separately. 2. Select the frequency band to be adjusted. 63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz / 16kHz b When "L/R CH" or "Each CH" is selected, select the speaker to be adjusted. 3. Adjust the level. -20.0dB ~ +6.0dB (0dB) Base Curve Copy Yes : Copy. Copy the MultEQ "Audyssey No : Do not copy. Flat" correction curve. "Base Curve Copy" is displayed after the Audyssey Auto Setup procedure has been performed. Default Yes : Reset to the defaults. Reset the "Manual EQ" No : Do not reset to the defaults. settings to their defaults. 47 Remote control operation buttons Displaying the menu : Cancel the menu : Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menu