Denon AVR5700 Owners Manual - Page 33
Learning function
UPC - 081757503778
View all Denon AVR5700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 33 highlights
Learning function • If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can "teach" the AVR-5700's remote control to "learn" the codes from the component's original remote control. • The buttons that can be "learned" are the CD, DECK and MD system buttons (see page 29) and the DVD, VDP, VCR and TV system buttons (see page 32). (For the CD, MD, DVD, VDP and TV, the A block buttons can also be "learned", and for the DVD and TV, the B block buttons can also be "learned".) SET CALL OFF ON / SOURCE DVD VDP TUNER SHIFT 1 2 3 1 Press the USE/LEARN selector button with the tip of a pen etc., to set the learn mode. Both the START and LEARNED/TX indicators flash. Flashes A TV/DBS 4 VCR-1 7 VCR-2 +10 V.AUX 5 CD 8 0 PHONO 6 MD / TAPE-1 9 TAPE-2 MON CHANNEL TV/VCR A / B 4 This unit's remote control unit 2 Set the program switch to the side to be "learned". Set to the AUDIO side for the CD, tape deck or DAT position, to the VIDEO side for the VDP, VCR or TV position. AUDIO 2 1,8 VOLUME DISC SKIP+ DOLBY / DTS HOME THX CINEMA SURROUND DIRECT DSP SIMULATION 5CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO DECK MD CD LOCK MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND MODE MEMORY TITLE MENU/GUIDE CH SELECT ENTER SELECT PANEL ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP 3 B AVR/AVC VIDEO 5 Check that the START LED is lit, then press the button to be "learned" on the other remote control unit. 3 Set the program switch to the position to be "learned". DECK MD CD LOCK DVD TV VDP VCR 4 Set the remote control units so they are facing each other, then press the button to be "learned" on this unit's remote control unit. Transmitting windows Lit Other remote control unit Other remote control unit This unit's remote control unit 6 Once the START LED turns off and the LEARNED/TX LED lights, release the button on the other remote control unit. This unit's remote control unit Approx. 5 cm The indicator stops flashing and the START LED lights. The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, DAT and tape deck, the buttons which can be operated with the preset memory for the VCR, VDP and TV. For the TV only, however, the buttons in the section indicated "A" on the diagram above can also be "learned". Use these to "learn" TV channels. The two LEDs start flashing again. Lit 7 To "learn" other buttons, repeat steps 2 to 6. 8 Once the learning operation is completed, press the USE/LEARN selector button again. The two LEDs stop flashing and the learning mode is cancelled. Check that the stored codes work properly. NOTES: • Up to 26 codes can be "learned", but this number may be lower if the codes are long. • If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released. • If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-853. • If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored. To "learn" that code, first perform the resetting operation. (See page 36.) 33