Denon AVR5700 Owners Manual - Page 6
Connections - avr5700s m
UPC - 081757503778
View all Denon AVR5700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
5 CONNECTIONS • Do not plug in the AC cord until all connections have been completed. • Be sure to connect the left and right channels properly (left with left, right with right). • Insert the plugs securely. Incomplete connections will result in the generation of noise. • Use the AC OUTLETS for audio equipment only. Do not use them for hair driers, etc. • Note that binding pin plug cords together with AC cords or placing them near a power transformer will result in generating hum or other noise. • Noise or humming may be generated if a connected audio equipment is used independently without turning the power of this unit on. If this happens, turn on the power of the this unit. Connecting the audio components • When making connections, also refer to the operating instructions of the other components. OUTPUT RL RL CD player DIGITAL AUDIO Connecting a CD player Connect the CD player's analog output jacks (ANALOG OUTPUT) to this unit's CD jacks using pin plug cords. Pre-main (integrated) amplifier for multi-source playback Connecting a turntable Connect the turntable's output cord to the AVR5700's PHONO jacks, the L (left) plug to the L jack, the R (right) plug to the right jack. NOTE: This unit cannot be used with MC cartridges directly. Use a separate head amplifier or step-up transformer. If humming or other noise is generated when the ground wire is connected, disconnect the ground wire. Ground wire NOTE: Refer to page 10 for notes on the shorting pin plugs. Turntable (MM cartridge) Connecting the pre-out jacks Use these jacks if you wish to connect external power amplifier(s) to increase the power of the front, center and surround sound channels, or for connection to powered loudspeakers. For instructions on using the effect output, refer to page 41. Connecting the AC OUTLETS AC OUTLETS • SWITCHED (total capacity - 120 W (1 A.)) The power to these outlets is turned on and off in conjunction with the POWER switch on the main unit, and when the power is switched between on and standby from the remote control unit. No power is supplied from these outlets when this unit's power is at standby. Never connect equipment whose total capacity is above 120 W (1 A.) NOTE: Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other electrical appliances. Extension jacks for future use AC cord (included) AC outlets (wall) AC 120 V, 60 Hz IN AM RL RL FM PHONO COAX. 75 R SIGNAL CD GND LOOP ANT. DVD MULTI SOURCE OUT L FRONT CENTER SUB WOOFER R VDP SURROUND ANTENNA TERLMINALS TV/ DBS 6CH EXT. IN V.AUX FR FL VCR-1 EFECT PREOUT R L OUT R L VCR-1 MONITOR OUT-1 MONITOR OUT-2 DVD IN VDP TV / DBS V.AUX VCR-1 Y IN CB CR Y CB CR DVD IN TV/DBS COMPONENT VIDEO Y CB CR MONITOR OUT ROOM TO ROOM REMOTE CONTROL IN OUT SPEAKER IMPEDANCE FRONT,CENTER /6 16 SURROUND / A OR B 6 16 A+B 12 16 FRONT R L CENTER SPEAKER SYSTEMS SW C VCR-2 R SR SL MD/ TAPE-1 L ER EL TAPE-2 8CH EXT. IN R VCR-2 R L MD / TAPE-1 VCR-2 OUT VCR-1 DOLBY DIGITAL IN RF 1 TAPE-2 AUDIO L R VCR-2 VIDEO L S-VIDEO OPTICAL 2 3 OPTICAL-5 4 IN OUT DIGITAL IN COAXIAL 1 2 3 AC IN SURROUND R A L R B L SURROUND SWITCHED TOTAL 120W(1A.) MAX. AC 120V 60Hz AC OUTLETS R LR L Tape deck 2 Route the connection cords, etc., in such a way that they do not obstruct the ventilation holes. MD player, DAT deck or other component equipped with digital input/output jacks R LRL OUTPUT INPUT Connecting a tape deck Connections for recording: Connect the tape deck's recording input jacks (LINE IN or REC) to this unit's tape recording (OUT) jacks using pin plug cords. Connections for playback: Connect the tape deck's playback output jacks (LINE OUT or PB) to this unit's tape playback (IN) jacks using pin plug cords. OUTPUT INPUT R LRL Tape deck 1 or MD R LR L OUTPUT INPUT OPTICAL OPTICAL COAXIAL OUTPUT CD player or other component DIGITAL AUDIO equipped with digital output jacks Connecting the DIGITAL jacks Use these for connections to audio equipment with digital output. Refer to page 25 for instructions on setting this terminal. NOTES: • Use 75 Ω/ohms cable pin cords for coaxial connections. • Use optical cables for optical connections, removing the cap before connecting. 6