Dewalt D25300D Instruction Manual

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

D25300

Dust Extraction System

Dispositif d'extraction des poussières D25300

Sistema de extracción de polvo

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

Questions? See us on the World Wide Web at www.dewalt.com

D

E

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

(APR-04) Form No. 583980-01

D25300

Copyright © 2003

The following are trademarks for one or more D

E

WALT power tools: the yellow and black color scheme; the “D” shaped

air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps

on the surface of the tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

E

WALT TOOL,

CALL US TOLL FREE AT:

1-800-4-D

E

WALT (1-800-433-9258)

General Safety Instructions

WARNING! Read and understand all instructions.

Failure to follow all

instructions listed below may result in electric shock, fire and/or serious

personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•

Keep your work area clean and well lit.

Cluttered benches and dark areas invite acci-

dents.

•

Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust

or fumes.

•

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

•

Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified

electrician if you are in doubt as to whether the outlet is properly grounded.

If the

tools should electrically malfunction or break down, grounding provides a low resistance

path to carry electricity away from the user.

Applicable only to Class I (grounded) tools.

•

Double insulated tools are equipped with a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec-

trician to install a polarized outlet. Do not change the plug in any way.

Double insu-

lation

eliminates the need for the three wire grounded power cord and grounded power

supply system.

Applicable only to Class II (double insulated) tools.

•

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your body is grounded.

•

Don’t expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

•

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately.

Damaged cords increase the risk of electric shock.

•

When operating a power tool outside, use an outdoor extension cord marked “W-

A” or “W.”

These cords are rated for outdoor use and reduce the risk of electric shock.

When using an extension cord, be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of

power and overheating. The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The

smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts

Total Length of Cord in Feet

120V

0-25

26-50

51-100

101-150

240V

0-50

51-100

101-200

201-300

Ampere Rating

More

Not more

AWG

Than

Than

0

-

6

18

16

16

14

6

-

10

18

16

14

12

PERSONAL SAFETY

•

Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication.

A moment of inattention while operating power tools may result in serious per-

sonal injury.

•

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts.

Loose clothing, jewelry, or long hair

can be caught in moving parts. Air vents often cover moving parts and should also be

avoided.

•

Avoid accidental starting. Be sure switch is off before plugging in.

Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•

Remove adjusting keys or wrenches before turning the tool on.

A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•

Do not overreach. Keep proper footing and balance at all times.

Proper footing and

balance enables better control of the tool in unexpected situations.

•

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•

Use clamps or other practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body is unstable and may lead to loss

of control.

•

Do not force tool. Use the correct tool for your application.

The correct tool will do the

job better and safer at the rate for which it is designed.

•

Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

•

Disconnect the plug from the power source before making any adjustments, chang-

ing accessories, or storing the tool.

Such preventative safety measures reduce the risk

of starting the tool accidentally.

•

Store idle tools out of reach of children and other untrained persons.

Tools are dan-

gerous in the hands of untrained users.

•

Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

•

Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool serv-

iced before using.

Many accidents are caused by poorly maintained tools.

•

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•

Tool service must be performed only by qualified repair personnel.

Service or main-

tenance performed by unqualified personnel could result in a risk of injury.

•

When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock or injury.

Additional Specific Safety Instructions for Dust

Extraction Systems

•

This attachment is intended for use in hammer drilling applications in masonry or concrete,

and with solid drill bits mounted to the power tool.

•

Do not use the

attachement for drilling applications in wood, steel or plastic.

•

Do not use the attachment in core drilling applications.

•

Do not use the attachment for chipping applications.

•

Do not

use this attachment with other tools than the models mentioned in this manual.

•

Do not use the tool in damp or wet conditions.

•

Do not operate this tool for long periods of time.

Vibration caused by the operating

action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to

provide extra cushion, take frequent rest periods, and limit daily time of use.

CAUTION: Wear appropriate hearing protection during use.

Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

•

lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry products, and

•

arsenic and chromium from chemically-treated lumber

(CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING:

Use of this tool can generate and/or disburse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face and body.

•

The label on your tool may include the following symbols. The symbols and their defini-

tions are as follows:

V

..........

volts

A

..........

amperes

Hz

........

hertz

W

..........

watts

min

......

minutes

........

alternating current

....

direct current

n

o

........

no load speed

........

Class II Construction

…/min ..revolutions or reciprocation per minute

........

earthing terminal

........

safety alert symbol

COMPONENTS (FIG. 1)

This attachment is suitable for use the the following models: D25303 and D25304.

A. Dust Extraction Head

E.

Release Button

B. Dust Brush

F.

Tool Rest

C. Depth Stop

G.

Dust Collector

D. Length Stop

ASSEMBLY

WARNING:

Unplug the tool before installing any accessory or making any kind of adjust-

ment to the tool

1. Before installing the D25300:

a. Remove the drill bit.

b. Remove the depth stop from the hammer side handle. DO NOT REMOVE THE SIDE

HANDLE.

c. Set the mode selector switch (H) to the ‘Hammer Drilling’ postion.

2. Align the D25300 with the tool as shown.

3. Slide the Dust Extraction System onto the tool, taking care that the contacts enter the con-

nection slots in the bottom of the tool.

4. Push the D25300 into place until the locking device engages.

5. To remove the D25300, press the release button (E) and pull the dust extractor off.

CAUTION:

Do not install or remove the dust extractor while the tool is running.

Adjusting the Drill Length

1. Insert the desired drill bit.

2. Press the depth stop and move it toward the head; release the stop.

3. Press the length stop and move it away from the head; release the stop.

Dewalt D25300D Instruction Manual

Dewalt D25300D Manual

Dewalt D25300D manual content summary: