Dymo LabelWriter® SE450 Label Printer Technical Reference
Dymo LabelWriter® SE450 Label Printer Manual
View all Dymo LabelWriter® SE450 Label Printer manuals
Add to My Manuals
Save this manual to your list of manuals |
Dymo LabelWriter® SE450 Label Printer manual content summary:
- Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 1
Technical Reference DYMO® LabelWriter®SE450 Label Printer - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 2
LabelWriter and DYMO are trademarks or registered trademarks of Sanford, L.P. All other trademarks are the property of their respective holders. Description: Direct Thermal Printer Model: LabelWriter SE450 installed and used in accordance with the instructions, may cause harmful interference to radio - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 3
RS-232 Settings 3 RS-232 Cabling 4 RS-232 Signal Levels 4 Programming Overview 5 Programming the LabelWriter Printer 5 Resetting the Printer 6 Command Parameters 6 Character Evaluation 6 16-Bit Character Parameters 6 Conversions 7 Font Specifications 8 Objects 8 Print Modes - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 4
CR Carriage Return 19 DC4 Cancel Double Wide Mode 19 ESC A Return Printer Status 20 ESC a Return Hardware Status 20 ESC B Set Dot Tab 20 ESC c Set Print Temperature to Low 21 ESC D Set Bytes per Line 21 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 5
q Print UPC/EAN Checksum 44 GS RS Set Inverse Print Mode 44 GS S Return Printer Status 45 GS T Select Line Wrap/Truncate Modes 46 GS t Set Characters per Line 53 Character Codes 55 Configuration Menu 65 Printer Specifications 67 Hardware Specifications 67 Interface Specifications - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 6
This page intentionally left blank for double-sided printing. vi - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 7
Or, for driver-less applications, the printer can be connected and driven entirely by ASCII Escape commands. This makes the LabelWriter SE450 an ideal printer to use in embedded applications, including medical devices, paint matching systems, and so on. The LabelWriter SE450 printer can accept label - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 8
This page intentionally left blank for double-sided printing. 2 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 9
with the LabelWriter SE450 printer, the communication parameters must be set as follows: Baud Rate 9600 Data Bits 8 Stop Bits 1 Parity None These settings can often be set using a BIOS setup program or an Operating System Control Panel application. For embedded applications, you may - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 10
is ready to receive data 2 3 RX In Data to the printer 3 2 TX Out Data from the printer 4 5 GND -- Signal, earth, and power ground 5 7 CTS In Depends on software selection 6 6 DTR Out Indicate printer is online Modular Plug RS-232 Signal Levels The serial interface uses - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 11
guide). Both basic and advanced topics are explained so that you understand how the LabelWriter SE450 printer works. Programming the LabelWriter Printer The first step in controlling the LabelWriter SE450 printer is to understand how the printer works. As an ASCII-based printer, the LabelWriter - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 12
either cause the command to fail or result in subsequent data being lost. Character Evaluation Most of the parameters that are sent to the LabelWriter printer are evaluated based on their decimal value. It is very important to have a good understanding of what this means. The ASCII character that is - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 13
Programming the LabelWriter Printer To allow for longer distances to be specified, two 8-bit characters are used to specify the value, by combining them into one 16-bit character. Though the calculations are all performed within the printer itself, it is important to understand how the characters - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 14
below lists the specifications for the five internal fonts the LabelWriter printer supports. Height and width are expressed in dots. Font Setting . The LabelWriter printer may be in only one print mode at a time. Multiple areas may be printed in different print modes on a single label, but these - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 15
commands not available nor applicable to the LabelWriter SE450 printer are ESC G and ESC q (used to change rolls for the LabelWriter 450 Twin Turbo). Raster mode refers to printing using the LabelWriter 450 printing commands, and is most often used when using printer drivers to print from Windows - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 16
objects that have been placed on the landscape page and advance to the next label. After a landscape page is printed, the LabelWriter printer will remain in landscape mode. If more objects are sent to the printer, a new landscape page will be allocated, with a width equal to the previous page. To - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 17
of these commands. Instead, it always prints within the U.S. Postal Service's specifications. The limitations of each symbology must be adhered to when sending you must allow adequate room for the barcode to be printed on the label. If you ignore any of these items, the barcode that is printed may - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 18
width of the LabelWriter printer's print head. manual. See Also GS * Line Objects Line objects are created using the draw line in landscape mode command (GS l). Line objects may only be printed as part of a landscape page. If the length of a line object is set to exceed the printable area of a label - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 19
use to program your LabelWriter SE450 printer. Below are some of the things you can do with the commands: n Send line feeds and carriage returns n Define barcode size and position n Read firmware revision and printer status information n Define label size, and paper orientation n Print graphics in - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 20
Command Reference NAME ESC g ESC J n ESC L ESC M ESC P ESC Q ESC S ESC T ESC U ESC V ESC W n1 n2 ESC X n1 n2 ESC Y n1 ESC y ESC z ETB FF GS * n1 n2 t h w d1...dm GS A n1 n2 GS d n GS DC2 GS DC3 GS h n GS k n m d1...dk DESCRIPTION Set Print Temperature to High Feed n Lines Set Feed Length Set Font - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 21
by Function Position Control DESCRIPTION Set Feed Length Draw Line in Landscape Mode Print UPC/EAN Checksum Set Inverse Print Mode Return Printer Status Select Line Wrap/Truncate Modes Set Characters per Line (Landscape) Set Characters per Line (Portrait) Cancel Inverse Print Mode Set Print - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 22
Command Reference Font Control NAME CR ESC J n ESC X n1 n2 ESC Y n1 GS T n GS V n GS d n GS t n GS u n NAME 20h - FFh DC4 ESC T ESC M ESC P ESC S ESC U ESC X n1 n2 GS DC2 GS DC3 GS RS GS US DESCRIPTION Carriage Return Feed n Sublines Set Horizontal Starting Position Set Vertical Starting - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 23
l1 l2 m Printable Characters DESCRIPTION Reset to Power-up Condition Return Firmware Revision Wrap Data Enter Debug Mode Landscape Mode Graphics Set Feed Length Return Printer Status Draw Line in Landscape Mode NAME 20h - FFh DESCRIPTION Printable Characters 17 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 24
L ESC Q ESC a ESC c ESC d ESC e ESC F 1 n ESC y ESC z DESCRIPTION Raster Mode Graphics Raster Mode Compressed Graphics Reset to Defaults Reset Printer to Power-up Condition Return Printer Status Set Dot Tab Set Bytes per Line Form Feed Set Feed Length Set Top Margin Return Hardware Status Set Print - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 25
text position to the beginning of the next line. Note that the line feed, line feed/carriage return, carriage return, and carriage return/line feed instructions all behave as a single line feed. If the current line extends beyond the printable area, the text will wrap to the next printable area. All - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 26
guide. See the description of the GS S command for information on how to return the printer status. See Also GS S ESC a Return Hardware Status Description Provided for LabelWriter printer ETB (Raster Mode Compressed Graphics) commands. The LabelWriter SE450 printer prints up to 56 bytes (448 dots) - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 27
. This command is also supported by the LabelWriter SE300 and the LabelWriter 400 and 450 series printers. Expression ASCII ESC c for LabelWriter printer raster compatibility. This command defines the number of bytes in a single line of raster bitmap data. The LabelWriter SE450 printer prints - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 28
ESC E Decimal 27 69 Hex 1B 45 Parameters None ESC e Set Print Temperature to Default Used to adjust the printing strobe. This command is also supported by the LabelWriter SE300 and the LabelWriter 400 and 450 series printers. Expression ASCII ESC e Decimal 27 101 Hex 1B 65 Parameters 22 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 29
Lines Description Provided for LabelWriter raster compatibility. The command is used to feed the next "n" lines on the label. This command requires two is the default speed. This command is also supported by the LabelWriter 400 and 450 series of printers. ESC i Set Printing Speed to Barcode Used - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 30
of sublines to feed ESC L Set Feed Length Description Provided for LabelWriter raster compatibility. See the GS L command for information. See Also GS , prior to any printable characters. This font will remain in effect until the printer is reset (by the ESC @ or ESC * command) or another font - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 31
24 H x 12 W. Fonts may only be changed at the beginning of a line, prior to any printable characters. This font will remain in effect until the printer is reset (by the ESC @ or ESC * command) or another font is selected. See Also ESC M ESC S ESC T ESC U Expression ASCII ESC P Decimal 27 80 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 32
Provided for LabelWriter raster compatibility. ESC S Set Font to 20 cpi Description Changes to the 20 cpi micro font. The cell dimension is 16 H x 10 W. Fonts may only be changed at the beginning of a line, prior to any printable characters. This font will remain in effect until the printer is - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 33
Commands Fonts may only be changed at the beginning of a line, prior to any printable characters. This font will remain in effect until the printer is reset (by the ESC @ or ESC * command) or another font is selected. See Also ESC M ESC P ESC S ESC U Expression ASCII ESC T Decimal 27 84 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 34
ESC V Return Firmware Revision Description Returns ten ASCII characters (1765303v0G) that represents the firmware revision of the of the LabelWriter 450 series printers, with which the SE450 is 100% compatible. Expression ASCII ESC V Decimal 27 86 Hex 1B 56 Parameters None ESC W Wrap Data - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 35
Commands n2 are received successfully by the host, you can be reasonably assured that there is a LabelWriter printer attached connected and your program can communicate with the printer. Expression ASCII ESC W n1 n2 Decimal 27 87 n1 n2 Hex 1B 57 n1 n2 Parameters n1 first character to echo n2 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 36
text and barcode objects. Distance is specified in millimeters. The LabelWriter SE450 print head is 56 millimeters wide. Expression ASCII ESC Y n Parameters None ESC @ Reset to Power-up Condition Description Returns the printer to its power-up condition, clears all buffers, and resets all - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 37
host to expect for each line. However, the sum of the pixels must be equal to the bytes per line variable (ESC D, default on the LabelWriter SE450 printer is 56) multiplied by 8. No error checking is done on the incoming data and unexpected results will occur if this caution is not observed. Below - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 38
. The distance the media will advance depends on two factors: the feed distance specified by the GS L command and the presence of a punch hole. The LabelWriter printer will advance until a punch hole is detected or until the feed distance (specified by the GS L command) has been reached. When the - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 39
Commands None GS A Starting Position of Bar Code Description Defines the distance from the left where the first barcode will print. The distance is represented in n/203 inch (dot) increments. This command is used to center a barcode on a text line. Expression ASCII GS A n1 n2 Decimal 29 65 n1 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 40
Command Reference GS DC3 Expression ASCII GS DC2 Decimal 29 18 Hex 1D 12 Parameters None GS DC3 Cancel Double Height Description Cancels the double-height characters and returns the font to normal size. This command must be sent at the beginning of a line, before any printable characters. - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 41
part of the barcode. If the number of characters to be encoded is variable, the m parameters can be set to zero. This will cause the printer to read the next character sent as a delimiter character. Further characters will then be encoded into the barcode until a character is found that matches the - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 42
Command Reference Character Value n=2 m=6 m=7 m=8 m=9 m = 10 m = 11 m = 12 m = 13 m = 14 m = 15 m = 16 m = 17 m = 18 n=3 n=4 n=5 n=6 n=7 n=8 n=9 n = 10 n = 11 n = 12 n = 13 n = 14 n = 15 Barcode Symbology EAN/UPC Auto UPC - E EAN-8 invalid UPC-E + 2 UPC Auto (UPC-E/UPC-A) UPC-A UPC-E + 5, EAN-13 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 43
Commands For Data Matrix encoding, the LabelWriter SE450 printer supports only basic ASCII characters 0x00-0x7F. Data Matrix barcodes are only supported for 203 x 203 dpi modes. They are not supported for 203 x 136 dpi modes. Parameters n 15 (0x0F) option byte Bit 7: "Numbers-only" compression. - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 44
88 36 36 86 172 44 44 144 288 52 52 204 408 72 72 368 736 88 88 576 1152 104 104 816 1632 Supported Rectangular Data Matrix Symbol Sizes Rows Columns Number of Encodable ASCII bytes Encodable numeric bytes with "Numbers-only" compression 8 18 5 10 8 32 10 20 12 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 45
0 to 127 inclusive and provides for international character set support. l Numeric Compaction mode permits efficient encoding of numeric wide: 4 bar and 4 space elements with the largest element 6 module wide. SE450 specifies each module is 2 dots line wide. n Maximum possible number of data - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 46
error correction: 2 to 512 codewords per symbol. But due to the limitation of SE450's 2" Print head, the maximum data user can send in portrait and landscape mode as following: Portrait mode: Any giving Dymo label can hold the maximum PDF417 barcode symbol column and row specified as following - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 47
Commands e = user defined error correction level (0 to 8), if it is 0 which means the error correction level will be set according to PDF417 specification. It will be assigned as per the following Table: Error Correction Level Error Correction Codewords Number of Data Codewords 0 2 -- 1 4 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 48
Command Reference Parameters n1 most significant byte of the offset from the left (in dots) n2 least significant byte of the offset from the left (in dots) L1 most significant byte of the line length (in dots) least significant byte of the line length (in dots) where: L2 offset = inches/203 = (n1 * - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 49
Commands GS L Set Feed Length Description Sets the distance the print media will advance upon receipt of a form feed (FF or ESC E) command. The distance is defined as n/203 inches. The number of dots = n1 * 256 + n2. Expression ASCII GS L n1 n2 Decimal 29 76 n1 n2 Hex 1D 4C n1 n2 Parameters - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 50
digit for the specified barcode. The checksum digit is printed in the current font, at the current text position. Currently the only supported symbologies are the UPC/EAN barcodes. Expression ASCII n m d1...dm Decimal n m d1...dm Hex n m d1...dm Parameters n1 selects the barcode symbology - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 51
identical. ESC A is provided for compatibility with the LabelWriter raster bitmap label printer. If possible, you should use GS S in order 3 4 5 6 7 MSB Printer ready Not top of form RESERVED RESERVED RESERVED Paper loaded RESERVED Printer has no error Printer not ready Top of form RESERVED - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 52
Command Reference GS T Select Line Wrap/Truncate Modes Description Determines how to handle a text wrap condition. A text wrap condition occurs when text extends beyond the end of a line or a page. The default is to wrap at the end of a line and a page. Expression ASCII GS T n Decimal 29 84 n - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 53
Commands GS US Cancel Inverse Print Mode Description Cancels the inverse print mode (white on black) and returns text back to its normal attributes for the remainder of the current line. See Also GS RS Expression ASCII GS US Decimal 29 31 Hex 1D 1F Parameters None GS u Set Characters per - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 54
Command Reference GS V Set Print Orientation Description Causes the LabelWriter printer to print the data stored in the print buffer and then change to the selected orientation. See Also GS t Expression ASCII GS V n Decimal 29 86 n - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 55
n Codabar, thick barcodes = 2 * n GS ~ Enter Debug Mode Description Prints the received printer codes either as a Hex or ASCII dump. This allows you to debug print problems. The debug mode remains in effect until the printer is powered off. Expression ASCII GS ~ n Decimal 29 126 n Hex 1D 7E - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 56
Command Reference GS * Landscape Mode Graphics Description Prints a graphic image (in landscape mode only). Expression ASCII GS * n1 n2 t h w d1...dm Decimal 29 42 n1 n2 t h w d1...dm Hex 1D 2A n1 n2 t h w d1...dm Parameters n1 most significant byte of left offset n2 least significant byte - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 57
text position to the beginning of the next line. Note that the line feed, line feed/carriage return, carriage return, and carriage return/line feed instructions all behave as a single line feed. If the current line extends beyond the printable area, the text will wrap to the next printable area. All - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 58
of resistive elements that blacken the thermally sensitive label material. The resistive elements are 0.125 millimeters square (0.00492 inches) and are spaced at eight dots per millimeter (203.2 dots per inch) apart. The print head on the LabelWriter SE450 printer contains 448 elements. When a line - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 59
printer expects. See Also ESC B ESC D ETB Expression ASCII SYN d1...dn Decimal 22 d1...dn Hex 16 d1...dn Parameters d1 ... bytes of bitmap print data (max 56 bytes for LabelWriter dn = SE450 print heads). n The Caret Feature Some computing environments do not allow the user to send - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 60
Command Reference When using the caret feature, three-digit characters must always follow the caret (^). Also, while the caret feature is enabled, the printer will not work correctly with the LabelWriter Windows or Mac raster print drivers. 54 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 61
The Caret Feature Character Codes Below is a list showing the ASCII codes from 1 to 255. The list shows the ASCII characters and names, and the corresponding decimal, hexadecimal, and binary values. Char Name Decimal Hex Binary None NUL 0 00 0000 0000 ^A SCH 1 01 0000 0001 ^B STX - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 62
Character Codes Char Space 0 1 2 3 4 5 6 7 8 9 : 56 Name Decimal Hex ESC 27 1B FS 28 1C GS 29 1D RS 30 1E US 31 1F space 32 20 exclamation pt. 33 21 quotation mark 34 22 number sign 35 23 dollar sign 36 24 percent sign 37 25 ampersand 38 26 apostrophe 39 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 63
The Caret Feature Char A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Name Decimal Hex semicolon 59 3B less than sign 60 3C equal sign 61 3D greater than sign 62 3E question mark 63 3F at sign 64 40 capital A 65 41 capital B 66 42 capital C 67 43 capital D 68 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 64
Character Codes Char a b c d e f g h i j k l m n o p q r s t u v w x y z Name open bracket back slash close bracket caret underscore accent grave lowercase a lowercase b lowercase c lowercase d lowercase e lowercase f lowercase g lowercase h lowercase i lowercase j lowercase k lowercase l - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 65
Char { | } ~ Delete € Ž Name open brace vertical line close brace tilde DEL Euro ' ' " " • - - ˜ ™ Trademark š The Caret Feature Decimal Hex 123 7B 124 7C 125 7D 126 7E 127 7F 128 80 129 81 130 82 131 83 132 84 133 85 134 86 135 87 136 88 137 89 138 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 66
Character Codes Char › œ ž Ÿ Name Copyright Registered 60 Decimal 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 Hex 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 67
213 214 215 216 217 218 Hex BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA Binary 1011 1011 1011 1100 1011 1101 1011 1110 1011 1111 1100 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 68
Character Codes Char Name 62 Decimal 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 Hex DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA Binary 1101 1011 1101 1100 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 69
Char Name The Caret Feature Decimal Hex 251 FB 252 FC 253 FD 254 FE 255 FF Binary 1111 1011 1111 1100 1111 1101 1111 1110 1111 1111 63 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 70
This page intentionally left blank for double-sided printing. 64 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 71
more seconds. The green light will blink. 6. Release the feed button. 7. Start your communications software. 8. Press until the menu appears. Dymo LabelWriter SE450 Firmware Version 1765303v0G Printer Configuration Menu Type ? for help 9. Press ? for help. You should see the following on - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 72
Send XON/XOFF X1 Inhibit XON/XOFF C? Display Caret (^) Status C0 Disable Caret Command C1 Enable Caret Command 10. When you are finished, unplug the printer. The next time you connect power to the printer the changes you made will be in effect. 66 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 73
printer, interface, print head, and printing specifications. For additional serial interface specifications, refer to the next section in this chapter. Model LabelWriter SE450 Dimensions Width: 4-7/8" Height 5-3/4" Depth 7-1/4" Weight 1.5 pounds Paper Fixed 2.25" linear thermal head 67 - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 74
Printer Specifications Average Life Printing Method Speed Label Width Resolution Fonts Barcode Types 2 million lineal inches (over 31 miles) Print head is replaceable Direct thermal 40 labels per minute (115,200 Baud, Serial) 48 labels per minute (through DYMO Label V.8, USB driver) 48 labels per - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 75
to identify the driver to load. USB Vendor ID The USB Vendor ID (VID) assigned to DYMO by the USB Implementers Forum is 0x0922h (2338 Decimal). USB Product IDs The LabelWriter SE450 printer has the following unique Product ID: Printer Model Product ID (Hex) DYMO LabelWriter SE450 0x0400 Serial - Dymo LabelWriter® SE450 Label Printer | Technical Reference - Page 76
This page intentionally left blank for double-sided printing. 70
Technical Reference
®
DYMO LabelWriter SE450 Label Printer
®