Edimax HP-2002APn User Manual

Edimax HP-2002APn Manual

Get Edimax HP-2002APn PDF manuals and user guides View all Edimax HP-2002APn manuals
Add to My Manuals
Save this manual to your list of manuals

Edimax HP-2002APn manual content summary:

  • Edimax HP-2002APn | User Manual - Page 1
  • Edimax HP-2002APn | User Manual - Page 2
    assumes the entire cost of all necessary servicing, repair, and any incidental or consequential product you have purchased and the setup screen may appear slightly different from those shown edimax.com for the update. All rights reserved including all brand and product names mentioned in this manual
  • Edimax HP-2002APn | User Manual - Page 3
    Thank you for purchasing and using Edimax HP-2002APn 200Mbps PowerLine Ethernet Adapter with wireless Access Point. This device product complies with the HomePlug AV mode and IEEE802.11b/g (compatible with 1T1R 802.11n) wireless standards which providing up to 200Mbps / 150Mbps data transfer rate
  • Edimax HP-2002APn | User Manual - Page 4
    package contains the following components: „ One HP-2002APn PowerLine 200Mbps Ethernet Adapter „ One RJ-45 Cable (100cm) „ One Quick Installation Guide „ One CD-ROM (Including all the software utilities, drivers, Multi-languages Quick Installation Guide and User's Manual) If any item is missing or
  • Edimax HP-2002APn | User Manual - Page 5
    or the device is down. Radio switch is turned on. Data is being transmitted. Radio switch is shut off. Connection succeeds under Wi-Fi Protected Setup. Negotiation is in progress under Wi-Fi Protected
  • Edimax HP-2002APn | User Manual - Page 6
    you want to add to a powerline network through the Ethernet cable. 3. Plug the HomePlug product to the power outlet. 4. This device with the HomePlug will join in the powerline network automatically. 5. Buttons : Reset: The Reset button can restore the factory defaults. Group: The button is used
  • Edimax HP-2002APn | User Manual - Page 7
    The following is the architecture of various applications of the HomePlug products. Picture 1 : 5
  • Edimax HP-2002APn | User Manual - Page 8
    by setting user defined secure powerline networks. The Utility could help you to manager all of the HomePlug devices in the LAN. The Utility is not necessary when you use the internet via HP-2002APn. Please follow the procedures below to install the utility. Please note that the following
  • Edimax HP-2002APn | User Manual - Page 9
    2. The following screen will be displayed. Click "Next". 3. Click "Next" to install the utility in the default folder or assign the destination folder where you would like to install the HomePlug utility. 7
  • Edimax HP-2002APn | User Manual - Page 10
    4. Click "Finish" to complete the installation. 8
  • Edimax HP-2002APn | User Manual - Page 11
    " and select "All Programs\Edimax PowerLine Utility" in your computer, you will find the HomePlug utility. Please refer to the following sections for the descriptions of how to use the utility. Note : The Utility can help you to find all (14Mbps / 85Mbps / 200Mbps) Powerline devies. But the 14Mbps
  • Edimax HP-2002APn | User Manual - Page 12
    shown with the name. A color distinction in icons is made between HomePlug 1.0, HomePlug 1.0 Turbo and HomePlug 1.1 devices. By default, the icon is always accompanied by a device name. Password: by default the password column is blank and 'Enter Password' button can be used to enter it. To set the
  • Edimax HP-2002APn | User Manual - Page 13
    HomePlug device. MAC Address: the device's MAC address will be shown here. Add Button: it is used to add a remote device to the existing network by entering the device password password. A confirmation box will appear if the password was entered correctly and if the device was found in the powerline
  • Edimax HP-2002APn | User Manual - Page 14
    Scan Button: the button is used to perform an immediate search of the HomePlug devices connected to the Powerline network. By default, the utility automatically scans every few seconds and updates the display screen. 6.2 Privacy The Privacy screen provides the user with an option to maintain
  • Edimax HP-2002APn | User Manual - Page 15
    Default (Public Network): The user can always reset to the HomePlug network (Public) by entering "HomePlug" as the network name or by clicking on the "Use Default used to set the new network name (network password) to all HomePlug devices whose password has been entered for the same logical network.
  • Edimax HP-2002APn | User Manual - Page 16
    host computer which were used to communicate over HomePlug on the Powerline network. It includes powerline network name, computer user name, MAC Address of all NICs (Network interface card) connected to the computer, versions of all drivers and utilities, etc. Lower Panel The Lower panel contains
  • Edimax HP-2002APn | User Manual - Page 17
    Device Last Known Network name HomePlug chipset manufacturer name Date device last seen on the network MAC Firmware Version. (Turbo Only) The diagnostics information displayed may be saved to a text file for later use, or can be printed for reference for a technical support call. Devices, which are
  • Edimax HP-2002APn | User Manual - Page 18
    follow the easy steps in the Wizard. No instruction for the Setup Wizard is given here. If you lost the CD-ROM or you prefer the traditional web setup, please follow the procedures in this Manual to configure the HP-2002APn The default IP address of HP-2002APn is '192.168.2.8'.Before you start the
  • Edimax HP-2002APn | User Manual - Page 19
    IP address ' and you can assign "192.168.2.XXX" (where XXX=10~253), then click 'OK'. Note : If your original setting of computer is "Obtain an IP address automatically " & "Obtain DNS server address automatically" , you should reset to original settings when you finish the following HP-2002APn
  • Edimax HP-2002APn | User Manual - Page 20
    in the Wizard. No instruction for the Setup Wizard is given here. If you lost the CD-ROM or you prefer the traditional web setup, please follow the procedures in this Manual to configure the HP-2002APn Note : If your original setting of computer is "Obtain an IP address automatically " & "Obtain DNS
  • Edimax HP-2002APn | User Manual - Page 21
    Wireless configuration via Web Setup If you prefer the traditional web setup, please follow the procedures in this Manual to configure the HP-2002APn. The default IP address of HP-2002APn is " 192.168.2.8 " . Please input 'admin' in 'User name' field, and '1234' in 'Password' field, and click 'OK
  • Edimax HP-2002APn | User Manual - Page 22
    information" LAN For you to setup HP-2002APn's IP address, enable/disable DHCP, IGMP and IP address pool. Wireless You can setup SSID, wireless security and ACL here. Management For you to upgrade HP-2002APn's firmware, save current settings, reboot, reset to default settings and change password. 20
  • Edimax HP-2002APn | User Manual - Page 23
    Please note if new IP address is not in same segment with current IP address of your desktop, you will not configure HP-2002APn unless you change computer's IP address again. Field IP Address Subnet Mask LAN 2 Description The IP address of LAN interface. The default IP address is 192.168.2.8. The
  • Edimax HP-2002APn | User Manual - Page 24
    or disable DHCP service. The default setting is Server, it indicates DHCP service is enabled. After enabling DHCP service, you can configure the following parameters of the DHCP server: Start IP Address: The start IP address of the DHCP address pool. End IP Address: The end IP address of the DHCP
  • Edimax HP-2002APn | User Manual - Page 25
    7.3.1 Wireless Settings This page is for you to setup wireless settings. The parameters of Wireless Network are described as follows: Field Description the drop down list. 11b/g mixed mode 11b only 11g only 11b/g/n mixed mode (default) Network The maximum character number for SSID is 32 23
  • Edimax HP-2002APn | User Manual - Page 26
    other. The MAC address of the wireless interface. You may select a proper channel in the drop down list. The default channel is Channel 6. encryption mode, and the physical mode. You do not need to manually enter other MAC addresses of peer APs. The parameters of Lazy Mode are described as follows
  • Edimax HP-2002APn | User Manual - Page 27
    type with the peer AP, and then enter the MAC address of the peer AP. After finishing the settings, click the Apply button to apply the settings. Step 2 Enter the Wireless Security/Encryption Settings page, set the security mode of the HP-2002APN to accord with the peer AP. 2) Bridge Mode In the
  • Edimax HP-2002APn | User Manual - Page 28
    , and AES. If selecting WEP, TKIP, or AES, you need to set the encryption key. Set the encryption key. The MAC address of another AP that connects to the HP-2002APN by WDS. Step 2 On the Basic Wireless Settings page, set the same physical mode and encryption type with the peer AP, and
  • Edimax HP-2002APn | User Manual - Page 29
    AP (An AP that wants to connect to the HP-2002APN by WDS). On the Basic Wireless Settings page, set the WDS mode to be Repeater Mode, set the same physical mode and encryption type with the peer AP, and then enter the MAC address of the peer AP. After finishing the settings
  • Edimax HP-2002APn | User Manual - Page 30
    to display the Wireless Security/Encryption Settings page. On this page, set the security mode of the HP-2002APN to accord with the peer AP. Note: In the WDS mode, don't set any mixed modes WDS AP acts as Root Bridge, and enter the MAC addresses in the WDS table on the Basic Wireless Settings page 28
  • Edimax HP-2002APn | User Manual - Page 31
    (RDG) Extension Channel Description You may select Mixed Mode or Green Field. The default operation mode is Mixed Mode. You may select 20 or 20/40. The default channel bandwidth is 20/40. You may select Long or Auto. The default guard interval is Auto. You may select the MCS value from 0 to
  • Edimax HP-2002APn | User Manual - Page 32
    Field Description secondary bandwidth. When data is being transmitted, it can act as 40MHz bandwidth, and it can also acts as 20 MHz bandwidth independently. In this way, the data rate is doubled. Aggregation MSDU (A-MSDU) Enable or disable A-MSDU. MSDU is the aggregation of multiple MSDUs by
  • Edimax HP-2002APn | User Manual - Page 33
    7.3.1 Advanced Wireless Settings On this page, you may configure advanced wireless parameters, such as beacon interval, data beacon rate, and Tx power. Note: The advanced wireless setting is only for advanced user. For the common user, do not change any setting on this page. Advanced Wireless The
  • Edimax HP-2002APn | User Manual - Page 34
    indicates full power. Short Preamble Enable or disable short preamble. The default setting is Disable. Preamble defines the length of CRC correction block of real- time applications, such as streaming video, and Voice-Over-IP telephony. Short Slot Enable or disable short slot. Tx Burst Tx
  • Edimax HP-2002APn | User Manual - Page 35
    the competition of sending packets, it will acquire Txop time to send packets. If the txop value is 0, it is limited to be a MSDC (MAC Service Data Unit). 33
  • Edimax HP-2002APn | User Manual - Page 36
    the delay time of WMM access category. If you use voice or video service, you'd better set this parameter to be smaller in the fields of AC_VI and AC_VO. If it is E-mail or Web service, you should set a bigger value in the fields of AC_BE and AC_BK. Cwmin
  • Edimax HP-2002APn | User Manual - Page 37
    modify the parameters above, please refer to the WMM settings of your WMM products. 3) DLS (Direct Link Setup) HP-2002APN provides DLS function. Suppose that there are two WMM devices. Enter the MAC address of a WMM device in the DLS setting of the other device, and then connect the two WMM devices
  • Edimax HP-2002APn | User Manual - Page 38
    Step 4 If DLS succeeds, you can view the MAC address of wireless card A on the WMM page of wireless card B, and vice versa. Multicast-to-Unicast Converter Enable or disable Multicast-to-Unicast. After enabling
  • Edimax HP-2002APn | User Manual - Page 39
    This page allows you to configure wireless security modes and set the encryption keys, to prevent unauthorized access and monitoring. Select SSID SSID choice: select SSID that you want to configure. Security Mode This page provides 10 types of security modes, including OPEN, SHARED, WEPAUTO, WPA,
  • Edimax HP-2002APn | User Manual - Page 40
    1) OPEN The parameters of OPEN mode are described as follows: Field Description Security Select OPEN. Mode Default Key Select a key as the default key. WEP Keys Set 64-bit or 128-bit key. The key format is Hex or ASCII. (WEP Key1/2/3/4) 2) SHARED The parameters of SHARED mode
  • Edimax HP-2002APn | User Manual - Page 41
    Field Description Encrypt You may select WEP or None. Type Default Key Select a key as the default key. WEP Keys Set 64-bit or 128-bit key. The key format is Hex or ASCII. (WEP Key1/2/3/4) 3) WEPAUTO The parameters' description of WEPAUTO mode, please refer to OPEN mode. 39
  • Edimax HP-2002APn | User Manual - Page 42
    the key renewal interval. WEP Keys Set 64-bit or 128-bit key. The key format is Hex or ASCII. (WEP Key1/2/3/4) IP Address The IP address of RADIUS server. Port The default port number is 1812. You may change it according to the server setting. Shared The shared key that RADIUS server needs to
  • Edimax HP-2002APn | User Manual - Page 43
    Field Session Timeout Idle Timeout Description If this value is 0, it indicates that there is no session time limit. Set the idle timeout. 5) WPA-PSK The parameters of WPA-PSK mode are described as follows: Field Description Security Mode Select WPA-PSK. WPA Algorithms Select TKIP or AES.
  • Edimax HP-2002APn | User Manual - Page 44
    6) WPA2 The parameters of WPA2 are described as follows: Field Description Security Mode Select WPA2. WPA Algorithms You may select TKIP, AES, or TKIPAES Key Renewal Interval Set the key renewal interval. PMK Cache Period Set the PMK (Pairwise Master Key) cache period. PMK scheme allows the
  • Edimax HP-2002APn | User Manual - Page 45
    Port Shared Secret Session Timeout Idle Timeout Description The IP address of RADIUS server. The default port number is 1812. You may change it according to the server setting. The shared key that RADIUS server needs to authenticate. If this value
  • Edimax HP-2002APn | User Manual - Page 46
    8) WPAPSKWPA2PSK The parameters' description of WPAPSKWPA2PSK mode, please refer to WPA2-PSK. 44
  • Edimax HP-2002APn | User Manual - Page 47
    Mode Select WPA1WPA2. WPA Algorithms You may select TKIP, AES, or TKIPAES. Key Renewal Set the key renewal interval. Interval IP Address The IP address of RADIUS server. Port The default port number is 1812. You may change it according to the server setting. Shared Secret The shared key that
  • Edimax HP-2002APn | User Manual - Page 48
    10) 802.1X The parameters of 802.1X mode are described as follows: Field Description Security Mode Select 802.1X. IP Address The IP address of RADIUS server. Port The default port number is 1812. You may change it according to the server setting. Shared Secret The shared key that RADIUS
  • Edimax HP-2002APn | User Manual - Page 49
    to the wireless devices in the MAC list. Reject: Reject the access control to the wireless devices in the MAC list. Add a Enter the MAC address of wireless device that you want to station allow or reject. Mac After finishing the settings, click the Apply button to apply the settings. 7.3.2.1 WPS
  • Edimax HP-2002APn | User Manual - Page 50
    On this page, you can modify the WPS settings. WPS can make your client automatically synchronize with the AP setting, and establish connection. WPS Config 48
  • Edimax HP-2002APn | User Manual - Page 51
    the Reset OOB button to display the WPS default settings. WPS Progress WPS modes include PIN and PBC modes, At present, WPS supports three operation code, for example, 12345678. Step 2 On the Wi-Fi Protected Setup page, enter the PIN code of wireless client, for example, 12345678. Step 3
  • Edimax HP-2002APn | User Manual - Page 52
    Step 2 Select Registrar mode on the wireless client and enter the PIN code of the HP-2002APN. See the following figure: 3) PBC Mode Step 1 On the Wi-Fi Protected Setup page, select the PBC mode, and then click the Apply button. You may also press the WPS button on the rear panel. Step 2 Enable
  • Edimax HP-2002APn | User Manual - Page 53
    Wireless Settings --> Station List to display the Station List page. On this page, you can view the wireless networks that connect to the HP-2002APN. If there is any wireless network connects to HP-2002APN, refresh this page and the connection information of the wireless network is displayed. 51
  • Edimax HP-2002APn | User Manual - Page 54
    Account Enter the account that you want to change. Password Enter the password for the new username. Note: If you forget the account and the password, please press the Reset button. The system will return to the factory default settings. The default account and the password are Admin. 52
  • Edimax HP-2002APn | User Manual - Page 55
    7.3.2.4 Upload Firmware Click Administration --> Upload Firmware to display the Upload Firmware page. If you want to upload the firmware of the HP-2002APN, click the Browse... button to choose the correct new firmware, and then click the Apply button. System begins to upgrade firmware. After
  • Edimax HP-2002APn | User Manual - Page 56
    ... button to choose the settings on your PC, and then click the Import button to import the settings to AP. Load Factory Click the Load Default button, the system returns to the
  • Edimax HP-2002APn | User Manual - Page 57
    AC power line. The following pre-cautions should be taken when using this product: ‧Please read all instructions before installing and operating this product. ‧Please follow all warnings and instructions marked on the product. ‧Do not operate this product near water. ‧ This product should never be
  • Edimax HP-2002APn | User Manual - Page 58
    service personnel for the following conditions : # If liquid has been spilled into the product # If the product has been exposed to rain or water # If the product does not operate normally when the operating instructions are followed # If the product exhibits a distinct change in performance. 56
  • Edimax HP-2002APn | User Manual - Page 59
    57
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59