Edimax HP-5001 User Manual

Edimax HP-5001 Manual

Get Edimax HP-5001 PDF manuals and user guides View all Edimax HP-5001 manuals
Add to My Manuals
Save this manual to your list of manuals

Edimax HP-5001 manual content summary:

  • Edimax HP-5001 | User Manual - Page 1
  • Edimax HP-5001 | User Manual - Page 2
    , optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd. cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co., Ltd.
  • Edimax HP-5001 | User Manual - Page 3
    Buttons...5 2.3 LEDs...6 Chapter 3: Utility Software Installation ...7 Chapter 4: Using the Utility Software ...14 4.1 Main Tab ...14 4.2 Privacy Tab ...15 4.3 Diagnostics Tab ...16 4.4 About Tab...17 Chapter 5: Security (Group) Button...18 5.1 Forming a HomePlug AV Logical Network 18 5.2 Joining
  • Edimax HP-5001 | User Manual - Page 4
    -definition (SD) video distribution  Broadband Internet sharing  Internet Protocol Television (IPTV) and Voice over Internet Protocol (VoIP) applications 1.3 Compatibility 200Mbps and 500Mbps powerline devices (HomePlug AV standard) are incompatible and cannot be used with 14Mbps and 85Mbps
  • Edimax HP-5001 | User Manual - Page 5
    1.4 System Requirements Operating System CPU RAM Free Disk Space Network Interface Utility can support Windows 2000/XP/Vista/7 Intel Pentium III 2.0GHz (or higher) 128MB (at least) 20MB (at least) Fast Ethernet (100Mbps) network interface and an Ethernet cable 4
  • Edimax HP-5001 | User Manual - Page 6
    Chapter 2: Adapter 2.1 Ethernet Port You can connect the HP-5001 to a router, a computer, or any network device via this Ethernet port. 2.2 Buttons Reset Security (Group) Press and hold the reset button for 3 seconds to restore the powerline adapter to factory defaults. Press and hold the "
  • Edimax HP-5001 | User Manual - Page 7
     Synchronizing password Off Powered off Green/ Orange/ On Red Off Green: PHY RATE > 80Mbps Orange: 40Mbps < PHY RATE < 80Mbps Red: PHY RATE < 40Mbps Not in a powerline network 6
  • Edimax HP-5001 | User Manual - Page 8
    Installation Step 1 Before installing the utility software, make sure that no other powerline utility is installed on your computer. If any other utility software is installed, uninstall it and reboot the computer. Step 2 Insert the CD into your CD-ROM drive. When the following image appears
  • Edimax HP-5001 | User Manual - Page 9
    Note : You will get the following image, if your computer did not install WinPcap4.1.2 before. Please click "Apply" to install WinPcap4.1.2. 8
  • Edimax HP-5001 | User Manual - Page 10
    9
  • Edimax HP-5001 | User Manual - Page 11
    10
  • Edimax HP-5001 | User Manual - Page 12
    Step 4 When the setup wizard appears, click "Next" to continue. Step 5 Select where you want to install the utility software, and then click "Next". 11
  • Edimax HP-5001 | User Manual - Page 13
    12
  • Edimax HP-5001 | User Manual - Page 14
    Step 6 After the installation is complete, click "Close". Step 7 An icon will appear on your desktop. Click the icon to open the utility software. Note: You can manage all the connected powerline adapters with the utility software. However, installing the utility software is optional. 13
  • Edimax HP-5001 | User Manual - Page 15
    adapters in the network. Connect Rename Enter Password Add Scan Click "Connect" and the utility software will scan for other local powerline adapters. Select a device and click "Rename" to rename the device. By default, this column is blank. Select a device and click "Enter Password" to set
  • Edimax HP-5001 | User Manual - Page 16
    4.2 Privacy Tab In the "Privacy" tab, you can create a private network by changing the default network name and configure its security settings. If the network name is modified to anything other than the default, the network type in the "Main" tab will be changed to "Private". Set Local Device Only
  • Edimax HP-5001 | User Manual - Page 17
    4.3 Diagnostics Tab The "Diagnostics" tab displays the system information and history of all remote devices. The upper panel displays technical data concerning the software and hardware on the host computer and the lower panel displays the history of all remote devices. 16
  • Edimax HP-5001 | User Manual - Page 18
    4.4 About Tab The "About" tab contains some basic information about the software. You can also enable or disable the autoscan function under "Preferences". 17
  • Edimax HP-5001 | User Manual - Page 19
    Security (Group)" button. The "Power" LED indicates the operation status and result. 5.1 Forming a HomePlug AV Logical Network When two devices with different NMK values are connected to the same powerline and you want them to form a logical network, follow the following procedures: Step 1 Press the
  • Edimax HP-5001 | User Manual - Page 20
    Step 2 Press the "Security" button on any device in the network for less than 3 seconds. This should be done within 1 minute. Step 3 Wait for the connection to complete. The "Power" LED on both devices will blink evenly at 1-second intervals until the operation succeeds or fails. If the connection
  • Edimax HP-5001 | User Manual - Page 21
    , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, not authorized. This transmitter is restricted for use with the specific antenna tested in the application for certification. The antenna(s) used for this transmitter
  • Edimax HP-5001 | User Manual - Page 22
    21
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22