Electrolux CEI30EF5GS Wiring Diagram (All Languages)

NOTICE

-

This service data sheet is intended for use by persons

having electrical and mechanical training and a level of knowledge

of these subjects generally considered acceptable in the appliance

repair trade.

The manufacturer cannot be responsible, nor assume

any liability for injury or damage of any kind arising from the use of

this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important that

safe servicing practices be observed.

The following are examples, but without

limitation, of such practices.

1.

Before servicing or moving an appliance remove power cord from electrical

outlet, trip circuit breaker to OFF, or remove fuse.

p/n 316904410

(0905)

SERVICE DATA SHEET

-

Electric Ranges with ES 630B Electronic Oven Control

ELECTRONIC OVEN CONTROL (EOC) FAULT CODE DESCRIPTIONS

IMPORTANT

DO NOT REMOVE THIS BAG

OR DESTROY THE CONTENTS

WIRING DIAGRAMS AND SERVICE INFORMATION

ENCLOSED

REPLACE CONTENTS IN BAG

Resistance

Temperature

Detector

F10

F11

F13

F14

F15

F20

F23

F25

F30

F31

F90

Runaway temperature. Oven

heats when no cook cycle is

programmed.

Shorted keypad.

Internal software error in

EOC.

TST Display tail missing or

not connected.

Signal loss between oven

relay board & EOC.

Communication failure

between EOC & ESEC.

(Electric models only)

Communication failure

between VSC board and EOC.

Open probe connection.

Shorted Probe connection

Door lock motor latch failure

1. Check RTD Sensor Probe using the RTD scale found in the tech sheet.

Replace if defective.

2. If oven is overheating dsiconnect power from the range and unplug connector P1 from power supply

board. Reapply power to the range. If oven continues to heat when the power is reapplied, replace the

oven relay board.

3. Replace the EOC.

NOTE: Severe overheating may require the entire oven to be replaced should damage be extensive.

1. Reset power supply to range to see if failure code will clear.

2 Test ribbon harness and connectors between the TST panel and EOC. Replace if defective.

3. Replace the TST panel.

4. Replace the EOC.

Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.

1.Test ribbon harness and connections between TST panel and EOC. Replace if defective


3. Replace the EOC.

1. Test the harness and connections from EOC connector P16 to oven relay board J2.

2. Replace the oven relay board.

3. Replace the EOC.

1. Test wiring harness and connections between EOC connector P2 and ESEC 30 UIB P9.

2. Test wiring harness and connections between ESEC 30 UIB and ESEC 20 relay board.

3. Test wiring harness and connections between PS board 2 (P2) and ESEC 30 UIB connector P7

4. Test for approximately 9 volts DC output from PS board 2 at ESEC 30 UIB connector

P7, pins 1 & 5. If

output voltage is incorrect test incoming power supply to PS board 2 at harness connector P1 pins 1 & 4.

If

incoming power is correct (120 VAC) replace PS board 2. If output voltage is correct replace ESEC 30 UIB

5. Replace EOC.

1.

Check harness and connections between VSC board and EOC.

2.

Test for approximately 5 volts DC to VSC board at P6 connector pins 1 & 6. If voltage is correct replace

VSC board. If voltage is incorrect replace EOC.

1. (F30 or F31) Check resistance at room temperature & compare to RTD Sensor resistance chart. If

resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness

between EOC & Sensor Probe connector.

2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe.

Check for shorted Sensor Probe harness between EOC & Probe connector.

If latch motor does not run

when clean cycle is selected:

1. Check to see if latch motor coil is open. If open, replace latch motor assembly.

2. Test for 120 volts to the terminals of the latch motor. If voltage is correct and motor does not run replace

latch motor assembly. If voltage is not correct replace EOC.

If latch motor runs

when clean cycle is selected:

1. Check the wiring harness between EOC & latch motor switch. Repair or replace harness as needed.

2. Test operation of the switch contacts. Replace latch motor assembly if defective.

3. Check for binding of the latch cam, latch motor rod & latch motor cam.

4. If all situations above do not solve problem, replace EOC.

Fault

Code

Symptom

Suggested Corrective Action

2.

Never interfere with the proper installation of any safety device.

3.

GROUNDING:

The standard color coding for safety ground wires is

GREEN

or

GREEN WITH

YELLOW STRIPES

.

Ground leads are not to be used as current carrying conductors.

It is

extremely important that the service technician reestablish all safety grounds prior

to completion of service.

Failure to do so will create a potential safety hazard.

4.

Prior to returning the product to service, ensure that:

• All electric connections are correct and secure.

• All electrical leads are properly dressed and secured away from sharp edges, high-

temperature components, and moving parts.

• All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away

from all metal parts and panels.

• All safety grounds (both internal and external) are correctly and securely reassembled.

Control beeps -

only center burner

LED's are flashing.

RTD SCALE

Temperature (°F)

Resistance (ohms)

32 ± 1.9

1000 ± 4.0

75 ± 2.5

1091 ± 5.3

250 ± 4.4

1453 ± 8.9

350 ± 5.4

1654 ± 10.8

450 ± 6.9

1852 ± 13.5

550 ± 8.2

2047 ± 15.8

650 ± 9.6

2237 ± 18.5

900 ± 13.6

2697 ± 24.4

ESEC key display ribbon cable is

disconnected or defective.

Symptom

Likely failure condition/cause

Suggested corrective action

ELECTRONIC SURFACE ELEMENT CONTROL (ESEC)

1. Check / re-install ribbon at J3 connection on the ESEC 30 UIB.

2. Replace ESEC 30 UIB.

3. Replace TST panel.

Control beeps -

only left side burner

LED's are flashing.

ESEC key display ribbon cable is

disconnected or defective.

1. Check / re-install ribbon at J3 connection on the ESEC 30 UIB.



Control beeps -

all

burner LED's are

flashing.

E11 failure mode

- shorted keypad

or

E14 failure mode

- ESEC key reads

ribbon cable is unplugged or defective

or

E15 failure mode

- internal ESEC error or

signal loss between ESEC 30 UIB and

ESEC relay board.

Turn power off to appliance for 30 seconds - then reapply power.

Does error return within 5 seconds after reapplying power?

If

YES

then: Use

Solution A

shown below.

If

NO

then: Does error return after 30 seconds?

If

YES

then: Use

Solution B

shown below.

If

NO

then: Test operation. If error does not return then the condition was corrected by the power reset.

Solution A: E14 failure

; key reads ribbon cable is disconnected or defective:

1. Check / reinstall ribbon at J4 connection on ESEC 30 UIB.



Solution A: E15 failure

; ESEC error or signal loss between ESEC30 UIB & relay board:

1. Check harness and connections between connector P6 or ESEC30 UIB to connector J2 of ESEC realay

board. Repair or replace harness as needed.

2. If connection and harness are good then replace ESEC relay board.

3. If error remains then replace ESEC30 UIB.

4. If previous steps do not resolve the failure replace the TST panel.

Solution B: - E11 failure

; shorted keypad:

1. Reset power supply to appliance and see if failure code clears.

2. Check / re-install reibbon harness and connectors between the TST panel and ESEC 30 UIB.


4. Replace the ESEC 30 UIB.

“

Hot Surface

”

and

no element power

“

Hot Surface

”

in

display even when

surface is cold.

Surface element

hot, but no

“

Hot

Surface

”

appears

1.Correct wiring of that element and its hot surface limiter.

1. With power disconnected, check continuity of hot surface limiter contacts (1b-2b) at that element

’

s

terminalblock.contacts are closed even when the surface is cold replace element.

2. If hot surface limiter contacts (1B-2B) are open replace power board.

1. With power disconnected, check continuity of hot surface limiter contacts (1b-2b) at that element

’

s

terminalblock.contacts are closed even when the surface is cold replace element.

2. If hot surface limiter contacts (1B-2B) are open replace power board.

1. Check the wire harness connector and seat properly to Relay Board J4 connector.

2. Check surface harness for correct wiring from each element

’

s hot surface limiter - correct wiring or replace

harness if necessary.

3.Turn on all elements to Hi. Wait 3 minutes to ensure all surfaces are hot. Check continuity of limiter switch

circuit for each element. If circuit is open replace that surface element. NOTE: Limiter contacts can be

tested through the harness on Relay Board connector J4

4.Check the wire harness and connectors from ESEC 30 UIB P5 to Relay Board Connector J5. Replace

harness if defective.

5. Replace Relay Board.


At power-up

“

HE

”

in display and surface

element will not come ON. Surface element

and its hot surface limiter mis-wired.

1. Loose connector from surface element

harness to ESEC Relay Board J4

connector.

2. Miswiring of surface element harness.

3. Open limiter contacts in surface

element. (1b - 2b).

4. Failed harness or connector from UIB

to Relay Board.

5. Defective Relay Board.

6. Defective ESEC 30 UIB.

1. Hot surface limiter contacts stuck closed.

2. Defective Relay Board.

3. Defective ESEC 30 UIB.

Oven Calibration/Temperature adjustment - See Use & Care Guide.

Please

note: Changing calibration affects normal Bake mode. The adjustments made will not

change the Self-Cleaning cycle temperature.

Tech Sheet Abbreviations and Terminology

EOC

=

Electronic Oven Control

UIB

= User Interface Board

VSC

=

Variable Speed Control

ESEC

=

Electronic Surface Element Control

TSEC

=

Touch Sensor Electronic Control

PS

=

Power Supply

board (PS1 , PS2, etc.)

TST

= Touch Sensor Technology (touch control glass panel)

RTD

=

Resistance Temperature Device. (Temp Probe or Temp Sensor)

TCO

=

Thermal Cut Out also

“

Thermo Disc

”

or

“

Thermal Limiter

”

Electrolux CEI30EF5GS Wiring Diagram (All Languages)

Electrolux CEI30EF5GS Manual

Electrolux CEI30EF5GS manual content summary: