Electrolux E32AF75JPS Wiring Diagram
Electrolux E32AF75JPS Manual
 |
UPC - 012505227561
View all Electrolux E32AF75JPS manuals
Add to My Manuals
Save this manual to your list of manuals |
Electrolux E32AF75JPS manual content summary:
- Electrolux E32AF75JPS | Wiring Diagram - Page 1
1100 CW Opposite Shaft 0.13 Running ICE MAKER SPECIFICATIONS Electrical 115 vac (127 vac max) 60 Hertz Thermostat Opens at 48° F ( 9° C), Closes at 15° F ( -9° C) Models with orange wire close at 8.96° F (-12.8° C) Heater Wattage 165 ICE MAKER CONNECTOR PLUG CONNECTIONS Wire Number Wire - Electrolux E32AF75JPS | Wiring Diagram - Page 2
-
1 -
2
 |
 |
PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT MID-POINT
CONTROL SETTING
Capacitor Run or
Induction Run
70°F (21°C) Ambient
90°F (32°C) Ambient
Operating Time
40 to 50%
55 to 65%
Freezer Temperature
-3° to 3° F
-19° to -16° C
-3° to 3° F
-19° to -16° C
Low Side Pressure
(cut-in)
6 to 12 psig
41 to 83 kPa
6 to 12 psig
41 to 83 kPa
Low Side Pressure
(cut-out)
-1 to 3 psig
-4 to 21 kPa
-1 to 3 psig
-4 to 21 kPa
High Side Pressure
(last 1/3 cycle)
85 to 100 psig
575 to 670 kPa
120 to 135 psig
810 to 910 kPa
Wattage (last 1/3 cycle)
100 to 120
110 to 130
Amps (running)
.9 to 1.1
1.0 to 1.2
Base Voltage
115 vac (127 vac max)
DEFROST SPECIFICATIONS
Cabinet Size
Thermostat
Heater
Cut-in
Cut-out
Watts
Ohms
19’
21° F (-6° C)
42° F (6° C)
550
24
Electronic Timer - Defrost 30 minutes every 12 hours of compressor run time.
CONDENSER FAN MOTOR
Watts
RPM
Amps
2.3
1100 CW Opposite Shaft
0.13 Running
ICE MAKER SPECIFICATIONS
Electrical
115 vac (127 vac max) 60 Hertz
Thermostat
Opens at 48° F ( 9° C), Closes at 15° F ( -9° C)
Models with orange wire close at 8.96° F (-12.8° C)
Heater Wattage
165
ICE MAKER CONNECTOR PLUG CONNECTIONS
Wire Number
Wire Color
Connects to:
1
Green/Yellow
Ground
2
Yellow
Water Valve
3
Black
Line
4
Light Blue
Neutral
IMPORTANT: PLEASE RETURN THIS SHEET TO IT’S
ORIGINAL LOCATION
ICE MAKER INFORMATION
Test Cycling
Remove cover by inserting screwdriver in notch at
bottom and
prying cover from housing. Use screwdriver to rotate motor gear
counterclockwise until holding switch circuit is completed. All
components of ice maker should function to complete the cycle.
T
U
R
N
Mounting
Plate
Screws
Mounting
Plate
Screw
Motor
Gear
Timing
Gear
Water Fill
Adjustment
Water Fill Volume
The water fill adjustment
screw will change the
fill time. One full turn is
equal to 20cc (.68 oz.).
The correct fill is 95 to
105cc (3.2 to 3.6 oz.).
When a water valve is
replaced, the fill volume
must be checked.
SERVICE DATA SHEET
-
297299800
STANDARD - AUTOMATIC DEFROST
FREEZER
MODELS (
R134a)
IMPORTANT SAFETY NOTICE
The information provided herein is designed to assist qualified
repair personnel only. Untrained persons should not attempt to
make repairs due to the possibility of electrical shock. Disconnect
power cord before servicing.
IMPORTANT
If any green grounding wires are moved during servicing,
they must be returned to their original position and properly
secured.
CAUTION:
All electrical parts and wiring must be
shielded from torch flame. Do not allow torch to contact
insulation; it will char at 200°F.
NOTE:
Products come equipped with an Electronic Defrost
Control. To initiate defrost, press and hold air filter and alarm
reset key simultainiously for three seconds.
To terminate defrost,
press and hold air filter and alarm reset key simultainiously for
three seconds
POWER
ICE MAKER
ICE MAKER
I
CE MAKER
ICE MAKER
WATER VALVE
LINE
THER MAL
CUT-OUT
HOLD
SW ITCH
T HERMOSTAT
SHUT-OF F
SWITCH
WATER FILL
SWITCH
MOLD HEATER
MOL D
MOUN TING
PLATE
MOTOR
NEUT RAL
BLK
BLK
B LK
BLK
BLU
LT. BLU
LT. BLU
BRN
RED
GRN / YEL
GRN / YEL
RED
YEL
YEL
YEL
P-3
P-1
P-2
P-4