Electrolux EDW7505HSS Installation Instructions

Dishwasher

Installation

Instructions

Printed in U.S.A.

154744001

10/10

INSTALLER:

Leave

Installation

Instructions

with owner.

OWNER:

Read your dishwasher

Use and

Care

Guide.

It contains

important

safety information

for operating

this appliance.

It also has

many suggestions

for getting the best results from your dishwasher.

Read

all instructions

before

installing

dishwasher.

For your safety, please read and observe

all safety

instructions.

This

guide will help you anticipate

drain,

water,

and

electrical

connections,

and help you select

the

best

location

for

the

dishwasher.

Tip

Over

Hazard

Do not use dishwasher

until completely

installed.

Do not push down on open door.

Failure to

follow

this warning

can result in serious

injury.

Cut

Hazard

To prevent serious

injury

from

sharp

edges,

wear work

gloves when handling,

unpacking

or disassembling

unit.

Tools and Materials

Needed for

Installation

(Not

Included)

•

Drill, Electric

•

Drill Bit 118"

•

Driver, Socket

8/32",114",8118"

•

Flaring Tool/Tube

Cutter (for copper tubing)

•

Flashlight

•

Level

•

Pipe Joint Compound

(for iron pipe plumbing) or

Pipe Thread Tape (for sealing threads)

•

Pliers

•

Safety Glasses

•

Saw, Keyhole or Vf,

1_/2"to 2" Hole Cutters

•

Screw Drivers, Slotted and #2 Phillips

(magnetic tip

preferred)

•

Tape, Electrical

or Duct

•

Tape, Measuring

•

Wire Stripper or Utility Knife

•

Wrench,

Hex-end

•

Wrenches,

2 Adjustable

(for copper tubing)

or 2 Pipe wrenches

(for iron pipe plumbing)

Parts You Will Need*

(Not Included)

•

Drain Hose Clamp, 1W' Diameter

•

Brass Elbow,

90 ° with a 3/8"National Pipe Thread

• Conduit Connector

(UL Listed)

• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)

If required:

• "Y" Branch Tailpiece and

Connector

Kit (See Step 4)

• Air Gap Kit (See Step 4)

All the parts can be found at local hardware,

electrical

and

plumbing

supply stores.

Electric

Shock

Hazard

Disconnect

electrical

power at the

fuse

box or

circuit breaker box before

beginning

installation.

Failure to

follow

this warning

could result

in death

or serious

injury.

NOTE: Put unit on its back being careful not to pinch the

Water

Drain Hose.

1.

Remove two (2) screws at front of the kickplate assembly

using a

#2 Phillips screw driver.

2.

Tilt and pull forward to remove see figure 1.

NOTE:

It is not necessary

to remove the outer door for installation.

Outer

Door

Top Screws

Kickpiat_

Toeplate

Figure

1

Kickplate

Assembly

,

,

Locate water inlet valve behind kickplate on bottom left underside

of unit.See Figure

4. The valve has a V?' NPT female fitting.

Remove

Plug

Wrap 90 ° elbow (not included) with pipe thread tape (or apply

joint compound)

and thread it into water inlet valve.

When

tightened, elbow should point toward the left. To prevent bending

of bracket or breaking of valve, avoid overtightening.

See Figure

4.

Cabinet

Preparation:

As a precaution,

it is recommended,

but not required

that the

cabinets

enclosing

all sides of the dishwasher

(including

the

underside

of the countertop)

be sealed with an oil based

paint

or moisture-proof

polyurethane

to prevent possible steam/

moisture

damage.

Electric

Shock

Hazard

Observe all local codes and ordinances

for

electrical and plumbing connections.

All electrical

and plumbing work should be performed

by

qualified

persons. Failure to

follow

this warning

could result in death or serious

injury.

,

Make sure your location has the correct

drain, water, and

electrical

outlets to make the connections.

Do not install unit

under a

cooktop

range.

Damage

to tub or other

components

will

occur.

4%" max.

A

Figure 2

13/4"

Electricalwater

and

draidines

must

be confined

to shadedarea

Preferred

drain areas

(5/r

6"rain. clearance

required from unit to

underside of countertb

Front

*Heightonlyadjustable td N" max.when

installedin35tnax4tandardcabine#:utout

Left

_

245/8"_

//

/

,'

Doorin90

,,

open

position

\

waterinletandpowersu_pl_

location(middlebottomrear)

Figure

3

S

DIMENSIONS

DO

NOT

INCLUDE

INSLJ-ATION

-

INSLJ_ATION

BLANKET

MAY

BE COMPRESSED

UPON

INSTALLATION.

IMPORTANT:

For proper

operation

and appearance

of unit,

cabinet opening

should

have dimensions

as shown in Figure 2.

If unit is to be placed in a corner, there must be at least a 2-inch

side clearance to open door.

2.

Floor should be flat and free of any obstruction.

IMPORTANT:

Drain, water, and electrical

lines should

be

roughed-in

before

going any

further.

Electric

Shock

Hazard

Electrical,

water, and drain lines

must

be confined

to shaded areas in Figure

2.

Electric conductors,

water, and drain could be

damaged.

Failure to

follow

these instructions

could

result in

fire

or electric shock.

NOTE:

If dishwasher

is installed at end of a cabinet, sides and

back must be

fully

enclosed.

NOTE:

Cabinet

Seal

Kit

(Kit # 154662101).

This

kit

provides a

seal between the unit and cabinets once installation

is

complete.

(The Installation

Instructions

are located in the Kit)

Weight

Keep children

away

from

the

front

of the dishwasher

so

that they are not accidentally

hit by the door during

loading or unloading

or if door should

unexpectedly

open.

The weight of the door can cause injury.

Locating

the Connections

1.

Review dimensions

in Figure

2 to locate dishwasher's

drain,

water, and electrical

connections.

2.

All utilities

must be routed in shaded area in the

Figure

2.

IMPORTANT:

Disconnect

power

before

starting

installation.

Note: Locate the electrical

supply and dishwasher's

electrical

junction

box on right underside of unit behind kickplate

assembly.

See Figure

4. Determine where you will connect

to hot water supply.

Review

Figure

4 and note the location of

water inlet valve. Determine where you will connect the drain

hose.

3.

Cut access

holes for the Electrical,

Water and Drain hoses in the

shaded areas as shown in Figure

2.

4.

The dishwasher

operates on a 120 volt, 60 Hz electrical

supply.

Provide a separate

circuit with a fuse or circuit breaker rated for

at least 15 amps (20 amps if connected

with disposer)

but not

more than 20 amps.

5.

Pull electrical

cable through hole into installation area.

6.

Be sure water inlet valve is protected from freezing.

Ifvalve

freezes and ruptures, flooding may occur.

7.

Determine amount of tubing needed to connect hot water supply

to the unit's water inlet valve.

Extra hose length

is necessary.

High-pressure

and high-temperature

Stainless Flexible hose with

a minimum

inner diameter of V4"may be used. A shut-off valve

installed outside

dishwasher

cabinet is best.

8.

Route water supply line into installation

area.

9.

Stand dishwasher

back upright for further installation.

IMPORTANT:

Incoming

hot water

temperature

should

be at

least

120°F (49°C).

Water

pressure

should

be between

20-90

psi.

Water Line

Brass Elbow

Electrical Line

(Not Included)

(Not Included)

Figure

4

Property Damage

Do not use the

furnished

drain hose or a rubber garden hose

for

the water supply line. Either of these hoses can burst.

Flooding

may occur and cause property damage.

'::::::

DrainH0seC0nnect

Or

2

k

EndStorageLocation

NOTE:

Pull the hose from "End Storage Location"

side.

See images below to connect the Drain Hose.

L

Take drain Hose out of dishwasher and find the end that

doesn't have the black rubber material.

2.

Use only the spring clamp that is provided in the accessory

kit, place spring clamp over one of the hoses. See Image

Below.

Hose Attached

To Dishwasher

Remove

Plastic

End

Plug

Of Hose

Clamp

Hose Shipped

Inside Dishwasher

3.

Take the plastic side of the drain hose and insert it into the

hose that is already attached to the dishwasher

make sure

hose ends are flush against each other.

See image

below.

4.

Secure the spring clamp 1/8" from large end of black hose to

the plastic side that was inserted for best sealing results.

See Image

Below.

Plastic

Ends

of

Hoses

Flush

Hose

Attached

to

Dishwasher

Tighten

Spring

Clamp

,

Measure height of cabinet opening from underside of countertop

to floor. Check chart for height opening and suggested

adjustment.

Leg Leveler Adjustment

Chart

Height of

Number of Turns to

Cabinet Opening

Adjust Levelers

34" (86.4cm)

0

34W' (86.7cm)

2

348h?' (87.2cm)

6

34Vf (87.6cm)

9

2.

Move dishwasher

to front of installation area.

3.

Loosen the rear leveling legs by turning counterclockwise.

Refer

to chart for number of turns.

Dishwasher

Anchoring

4.

Install the Cabinet

Seal Kit (Instructions

included in Kit)

5.

Choose one of the methods of attachment

below to secure unit,

holes need to be pre-drilled

using a #5 drill bit regardless

of

the option chosen:

a. Side Mount Cabinet Clips (Preferred

Method of attachment)

b. Top Mount Cabinet Clips (to be used when Side Mount

is not an available

option)

CAUTION:

Use extreme

care

in mounting

the dishwasher

as to not

scratch,

bump

or otherwise

damage

the console

or tub.

To install

the Side

Mounting

Clips.

Depending

on space allowed in cabinet the Side Mounting

Clips can be installed with the holes for the screw up (preferred

method) or down as shown in the illustrations

below.

(Use extreme

caution when the clips are in the down position while installing

the dishwasher).

NOTE: Install

Side

Mount

Brackets

before

unit is installed

into

the cabinet.

Insert

screws

into the front

holes of the

mounting

clips

only.

(See image

below)

Use

if

measures

34V8"

to

35"

screw

Use

if

measures

34" to 34V8"

screw

To

install

using Top Mount Cabinet Clips:

Depending on the depth of cabinet, the Top Mount

Clip have a break off point that can be removed

if

necessary.

NOTE:

Install

Top

Mount

Clips

before

unit is installed

into the

cabinet.

Screw

clips

firmly

to top brace using

screws

provided

in the literature

pack. (See

image

below)

/////////////////////

k¸

!I

I

Electrolux EDW7505HSS Installation Instructions

Electrolux EDW7505HSS - Semi-Integrated Dishwasher With 5 Wash Cycles Manual

Electrolux EDW7505HSS manual content summary: