Electrolux EIFLW55HIW Wiring Diagram (All Languages)
Electrolux EIFLW55HIW - 27" Front-Load Washer Manual
 |
UPC - 012505378607
View all Electrolux EIFLW55HIW manuals
Add to My Manuals
Save this manual to your list of manuals |
Electrolux EIFLW55HIW manual content summary:
- Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 1
Español 11-15 Wiring Diagram 16 Acronyms: MB - Main Board (Board located inside machine on right side just behind control panel.) MC - Motor Control UI - User interface board (board located inside the front control panel) DL - Door Lock READING ERROR CODES 1. Wake the washer up by pressing any - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 2
the cycle such as "CALL SERVICE", "NO WATER" or "CHECK HOSES". Correct the action and repeat the cycle for proper installation. Washer will exit the Install Cycle and return to normal operation the next time the knob is turned. 1¼"x4¾" Display Models 1. The machine will first wake up on setting - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 3
. E41 Control board thinks the door switch is open. E42 Door lock device failure E44 Door closed sensing failure. E45 Line door sensing failure. E46 Door command sense. E49 Door incngruence between door line and door sense. E52 Bad signal from tacho generator. E53 Low Voltage to Motor Control Board - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 4
3 1. Check the drain hose for restrictions. 2. Start the washer and check for 120 VAC at the drain pump. Test 4 washer continuously? 3. Remove power from washer. Does the water stop coming in? 4. Replace the pressure sensor switch. Did this correct the problem? Test 6 1. Is the loading door closed - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 5
, replace the motor control board. Test 11: 1. Communication problem. Check the wiring between Wiring bad. Correct wiring problem. Wiring good. the main control board and the user interface board. Replace the user interface board. If the problem is not corrected, replace the main control board - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 6
commande se ferme peu de temps après avoir appuyé sur la touche "Start (Départ)/Pause". 2. Vérifiez si les connexions de la MB sont ajustées fermement. de programme de 1 clic dans le sens horaire à partir de la position Start (Départ). Le solénoïde d'eau chaude est activé et l'eau chaude doit entrer - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 7
programmes jusqu'à HAND WASH (Lavage à la main). 3. Appuyez sur START/PAUSE (Départ/pause), puis sur action en indiquant les messages CALL SERVICE (Demander du service), NO WATER (Pas d'eau) sur la touche de réglage, puis suivez les instructions indiquées (retirez tous les articles qui se trouvent - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 8
Tableau des codes d'erreur Code d'erreur Anomalie Vérification E11 Durée de remplissage trop longue. Se référer au test (1). E13 Fuite d'eau dans la cuve ou fuite d'air dans la cloche d'air. Se référer au test (2). E21 Eau pompée trop lentement. Se référer au test (3). E31 Défaillance du - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 9
Test Test 1 Test Vérification Correction 1.Est-ce que le flux d'entrée de l'eau est normal ? Oui. Passez à l'étape (4). 2.Est-ce que les robinets d'arrivée de l'eau sont ouverts? 3.Est-ce que la pression d'arrivée d'eau est supérieure à 20 psi ? Non. Passez à l'étape (2) Non. Ouvrez les - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 10
Test Test Vérification Correction Test 7 1.Débranchez le raccord du moteur et mesurez la résistance des broches 4 et 5 du moteur. Si la valeur lue se situe entre 105 et 130 Ohms, remplacez la carte de contrôle de moteur.Si le compteur indique d'autres valeurs que 105 et 130 Ohms, remplacez le - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 11
Hoja técnica de lavadora Esta información está destinada exclusivamente a los técnicos calificados. PRECAUCIÓN: DESCONECTE LA CORRIENTE ELÉCTRICA ANTES DE DAR MANTENIMIENTO O SERVICIO Por favor devuelva esta hoja a su sobre en el producto para referencia futura Contenido Página Explicación de los - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 12
Configurar. La máquina se apagará y cuando se encienda, las partes del programa que quiso restablecer se encontrarán con los valores de fá APROBADA); de lo contrario, durante el ciclo se indicará alguna acción, como "CALL SERVICE" (llame al servicio técnico), "NO WATER" (no hay agua) o "CHECK HOSES - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 13
Código de error Tabla de códigos de error Condición de falla E11 Demasiado tiempo para el llenado. E13 Fuga de agua en la tina o fuga de aire en la campana de aire. E21 El drenado de agua no es lo suficientemente rápido. E31 Falla del interruptor electrónico de presión. E32 Problema con la - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 14
Prueba Prueba 1 Prueba 2 Prueba 3 Prueba 4 Prueba 5 Prueba 6 Prueba 7 Prueba 8 Prueba Revise Corrección 1.¿El flujo del agua entrante es normal? 2.¿Están abiertas las llaves de agua? 3.La presión del agua entrante está sobre (20) psi. 4.¿El agua para llenado continúa entrando a la lavadora? 5. - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 15
Prueba Revise Prueba Corrección 3.Desconecte la clavija del motor y mida la resistencia de los pines (pin 1 a pin 2, pin 1 a pin 3, pin 2 a pin 3). Todas las lecturas deben estar entre 3 y 6 Ohms. Prueba 9 1.Quite la banda del motor y gire la polea del motor. ¿El motor gira libremente? 2.Gire la - Electrolux EIFLW55HIW | Wiring Diagram (All Languages) - Page 16
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
137022700A
(0805)
Washer Tech Data Sheet
This information is intended for Qualified Technicians Only.
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING
Please Return This Sheet to its Envelope in the Product for Future Reference
Contents
Page
Error code explanation
.............................................
1
Diagnostics
........................................................
1-2
Error Code Chart
.....................................................
3
Tests
..................................................................
4-5
Français…………………………………………
.........
6-10
Español…………………………………………
........
11-15
Wiring Diagram……………………………………
........
16
Acronyms:
MB – Main Board (Board located inside machine on right side just behind control panel.)
MC – Motor Control
UI – User interface board (board located inside the front control panel)
DL – Door Lock
READING ERROR CODES
1.
Wake the washer up by pressing any button (except the cancel button).
2.
Press and hold the
“Cancel
”
and
“Start”
buttons simultaneously for 6 seconds. The failure code will appear in the
display as an E followed by two numbers.
NOTE:
E00 means no failure code experienced.
Troubleshoot the problem by using charts on the pages 3-5.
If there is no error displayed and the washer momentarily starts then turns back off:
1.
Listen for a relay closure inside the control shortly after the
“Start/Pause”
key is pressed.
2.
Check the connections on the MB make sure that they are firmly snug and secured.
To clear latest stored error code:
•
Press the
“Cancel”
button to enter standby mode and enable diagnostic entry.
•
Within 10 seconds after pressing
“Cancel”
, press any button to wake up the control.
•
Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the
“Cancel”
and
the far left
button under the display
simultaneously for 3 seconds to enter the Diagnostic Mode.
(note: to save time at wake up,
the welcome screen can be bypassed by turning the selector knob).
•
Turn the program knob counter clockwise 9 turns (clicks) from the
S
t
art Position. The control will signal the last 5 error
codes with E00 meaning no error experienced.
•
Press and hold the
far left key under the display
and
“Cancel”
buttons simultaneously for 3 seconds. The code(s) will
be cleared.
•
To return the washer to normal operation.
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob clockwise 2 turns (clicks) back to the
S
t
art Position (LEDs are flashing).
Press the
“Cancel
” and
far left button under the display
until the LEDs stop flashing.
Diagnostic Test
The diagnostic test is used to check individual component function only.
T
O ST
ART THE TEST
:
•
Press the
“Cancel”
button to enter standby mode and enable diagnostic entry.
•
Within 10 seconds after pressing
“Cancel”
, press any button to wake up the control.
•
Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the
“Cancel”
and
the far left
button under the display
simultaneously for 3 seconds to enter the Diagnostic Mode.
(note: to save time at wake up,
the welcome screen can be bypassed by turning the selector knob).
1.
Upon entering Diagnostic Mode, all lights should flash for 1¼”x2” display models and all lights on for the 1¼”x4¾” display
models.