Electrolux EIGD55H Installation Instructions
Electrolux EIGD55H - Gas Dryer With 8.0 cu. Ft. Capacity Manual
 |
View all Electrolux EIGD55H manuals
Add to My Manuals
Save this manual to your list of manuals |
Electrolux EIGD55H manual content summary:
- Electrolux EIGD55H | Installation Instructions - Page 1
|nsta||ation |nstructions Electro[u× Front-Load Gas _ Electric DD'er |nstrucciones de |nsta|acion Secadora e[_ctfica y a gas de carga fro_3tal Electro[u× Instructions d'installation %cheuse _ gaz et _ l'_[ectficit_ _ chargeme_3t fro_3tal Electro[u× - Electrolux EIGD55H | Installation Instructions - Page 2
connection - Electric dryer (4-wire cord)... 13 Gas connection 14 Water connection (Steam Model only 15-16 General installation 17 Performing installation cycle 18 Reversing door 19-24 Options 25 Accessories 25 Replacement parts 25 Notes 26 ©2008 Electrolux Major Appliances All - Electrolux EIGD55H | Installation Instructions - Page 3
TO DO IF YOU SMELL GAS: • Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier. • Install the clothes dryer according to the manufacturer's instructions and local codes. • The electrical service to the dryer must conform with local - Electrolux EIGD55H | Installation Instructions - Page 4
loop connectors and marked for use with clothes dryers. For 4-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 4-WIRE SYSTEM. dryer is in the installed position. GROUNDING CONNECTION - See "Grounding requirements" in Electrical installation section. Electrical requirements for gas - Electrolux EIGD55H | Installation Instructions - Page 5
1. Installation MUST conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition). 2. The gas supply line should be 1/2 inch (1.27 cm) pipe. 3. If codes allow, flexible metal tubing may be used to connect your dryer to the gas supply - Electrolux EIGD55H | Installation Instructions - Page 6
installation Requirements Exhaust system requirements, continued The dryer must be 67m) 2 40 ft. (12.19m) 25 ft. (7.62m) 3 NOT RECOMMENDED Install male fittings in correct direction: In installations where the exhaust system is not described in the charts, the following method must be - Electrolux EIGD55H | Installation Instructions - Page 7
Part 280) or Standard CAN/CSAZ240 MH. 2. Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support to previous sections in this guide for other important exhaust venting system requirements. 5. When installing a gas dryer into a mobile home, a - Electrolux EIGD55H | Installation Instructions - Page 8
closet, MUST be exhausted outdoors. 2. No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3. Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. . Closet door ventilation required: A minimum of 120 - Electrolux EIGD55H | Installation Instructions - Page 9
line 15.25" (4t.5cm) * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90 ° elbow. Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to installation depth. Upward venting of exhaust on pedestal-mounted or freestandin - Electrolux EIGD55H | Installation Instructions - Page 10
electrical installation of your dryer. Failure to follow these instructions can create electrical shock and!or a fire hazard. ELECTRICAL SHOCK HAZARD This appliance MUST be properly grounded. Electrical shock can result if the dryer _snot properly grounded. Follow the instructions in this manual for - Electrolux EIGD55H | Installation Instructions - Page 11
Installation instructions Grounding requirements o Electric dryer (Canada} For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical - Electrolux EIGD55H | Installation Instructions - Page 12
the screw securing the terminal block access cover in the lower corner on the back of the dryer. • Install a UUapproved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel• At this time, the strain relief should - Electrolux EIGD55H | Installation Instructions - Page 13
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3. Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Electrolux EIGD55H | Installation Instructions - Page 14
'"l installation instructions 1. Remove the shipping cap from gas pipe at the rear of the dryer. . Open the shutoff valve in the gas supply line to allow gas to flow through the pipe. Wait a few minutes for gas to move through the gas line. DO NOT connect the dryer to LR gas service without - Electrolux EIGD55H | Installation Instructions - Page 15
Installation instructions Water connection (Steam Model only} . Turn off COLD water supply to washer, 2. Remove COLD container to clear any contaminants in the line. 4. Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers. RUBBER WASHERS MUST BE PRESENT - Electrolux EIGD55H | Installation Instructions - Page 16
installation instructions . If your installation has room for the COLD water supply to accept the "Y" hose's 90 ° coupling to the brass water inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers. 6. Turn on the water and - Electrolux EIGD55H | Installation Instructions - Page 17
performing a brief, helpful "Installation Cycle" for your new dryer. 7. If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 8. Place these instructions in a location near the dryer for future reference - Electrolux EIGD55H | Installation Instructions - Page 18
) and presence of gas supply (on gas models). At cycle completion, the LCD window may display II",STRLPRSFJ,meaning your new dryer is properly installed and ready for use. If it prompts an action such as S_R(/_C_COROI,I0 L-,RSor S_,LLS_{IlC_ 877 ff35 3_87, review the installation steps and make the - Electrolux EIGD55H | Installation Instructions - Page 19
work surface, such as top of dryer or floor near dryer, with a soft cloth or towel. 4 Be sure dryer is unplugged from power source! approximately _A"counter- clockwise and pull ring away from door. E:3 ;" 3 While supporting door with the other hand, remove 3 short, fine-thread, counter-sunk sc - Electrolux EIGD55H | Installation Instructions - Page 20
. Rotate striker and move to opposite opening. Attach with 2 short, course-thread, panhead screws. Remove 4 long, course-thread, recessed screws and hinge. Set hinge aside. \ \ 3 Install original plastic hole plugs or use new plugs supplied with - Electrolux EIGD55H | Installation Instructions - Page 21
E) Removing Latch Indicator Reversing Door F) Removing Hole Plug jj/J jf / _J Insert flat blade screwdriver into open slot of latch indicator. 2 Gently pry upward to release tab. 1 Insert flat blade screwdriver into open slot of hole plug. 2 Gently pry upward to release tab. 3 Pull the - Electrolux EIGD55H | Installation Instructions - Page 22
Reversing Door G) Reinserting Latch Indicator 1 Rotate the latch indicator and move it to the opposite hole in the door. insert indicator H) Reinserting Hole Plug 1 Rotate the hole plug and move it to the opposite hole in the door. 2 Firmly insert the two small tabs on either side of the hole plug - Electrolux EIGD55H | Installation Instructions - Page 23
. 2 Reattach with 2 long, course-thread, counter-sunk screws. K) Reattaching Door to Front Panel 1 Use side locating pins to align hinge and install 1 short, fine-thread, counter-sunk screw in center hole of hinge side. / / / / \ J) Reattaching Hinge 1 Rotate hinge and move to opposite side - Electrolux EIGD55H | Installation Instructions - Page 24
clockwise approximately 3/,,,. Rotate and move trim ring cover plate to opposite opening in trim and reinsert. N) Reinstalling Trim Plug 1 Open door to 90 degree angle. 2 Install trim plug with 1 long, course-thread, panhead screw. O) Plug in - Electrolux EIGD55H | Installation Instructions - Page 25
0 If you desire another stacking kit, you may order one. LP CONVERSION KIT P/N 134709300 Gas dryers intended for use in a location supplied with LP must use a conversion kit prior to installation. MOBILE HOME INSTALLATION KIT P/N 137067200 Installations in mobile homes require use of MOBILE HOME - Electrolux EIGD55H | Installation Instructions - Page 26
Notes
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
|nsta||ation
|nstructions
Electro[u×
Front-Load
Gas
_
Electric
DD'er
|nstrucciones
de
|nsta|acion
Secadora
e[_ctfica
y a gas
de
carga
fro_3tal
Electro[u×
Instructions
d'installation
%cheuse
_ gaz et _ l'_[ectficit_
_ chargeme_3t
fro_3tal Electro[u×