Electrolux EIGD55IKG Installation Instructions
Electrolux EIGD55IKG - IQ-Touch 8.0 cu. Ft. Capacity Gas Dryer Manual
 |
UPC - 012505379710
View all Electrolux EIGD55IKG manuals
Add to My Manuals
Save this manual to your list of manuals |
Electrolux EIGD55IKG manual content summary:
- Electrolux EIGD55IKG | Installation Instructions - Page 1
|nsta||ation |nstructions Electro[u× Front-Load Gas _ Electric DD'er |nstrucciones de |nsta|acion Secadora e[_ctfica y a gas de carga fro_3tal Electro[u× Instructions d'installation %cheuse _ gaz et _ l'_[ectficit_ _ chargeme_3t fro_3tal Electro[u× - Electrolux EIGD55IKG | Installation Instructions - Page 2
Information Please read and save this guide Thank you for choosing Electrolux, the new premium brand in home appliances. These Installation Instructions are part of our commitment to customer satisfaction and product quality throughout the life of your new appliance. We view your purchase as the - Electrolux EIGD55IKG | Installation Instructions - Page 3
and caution MUST be applied when installing, operating and maintaining any appliance. Read all of the following instructions before installing and using this appliance: • Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered with - Electrolux EIGD55IKG | Installation Instructions - Page 4
. Use separately fused circuits for washer and dryer. DO NOT operate a washer and a dryer on the same circuit. POWER SUPPLY - 3-wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current. with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE - Electrolux EIGD55IKG | Installation Instructions - Page 5
(foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers and in the United States must also comply with the Outline for Clothes Dryer Transition Duct, UL standard 2158A. Also, ensure the present duct is free of any - Electrolux EIGD55IKG | Installation Instructions - Page 6
installation Requirements Exhaust system requirements, continued The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Electrolux EIGD55IKG | Installation Instructions - Page 7
32-80 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSAZ240 MH. 2. Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 - Electrolux EIGD55IKG | Installation Instructions - Page 8
or closet, MUST be exhausted outdoors. 2. No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3. Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. . Closet door ventilation required: A minimum - Electrolux EIGD55IKG | Installation Instructions - Page 9
electrical supply on rear of unit height for rear vent optional pedestal floor line 15.25" (4t.5cm) * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90 ° elbow. Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to - Electrolux EIGD55IKG | Installation Instructions - Page 10
!or a fire hazard. ELECTRICAL SHOCK HAZARD This appliance MUST be properly grounded. Electrical shock can result if the dryer _snot properly grounded. Follow the instructions in this manual for proper grounding. Do not use an extension cord w_th this dryer. Some extension cords are not designed to - Electrolux EIGD55IKG | Installation Instructions - Page 11
instructions Grounding requirements o Electric dryer (Canada} For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. . Since your dryer - Electrolux EIGD55IKG | Installation Instructions - Page 12
the screw securing the terminal block access cover in the lower corner on the back of the dryer. • Install a UUapproved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel• At this time, the strain relief should - Electrolux EIGD55IKG | Installation Instructions - Page 13
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3. Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Electrolux EIGD55IKG | Installation Instructions - Page 14
'"l installation instructions 1. Remove the shipping cap from gas pipe at the rear of the dryer. . Open the shutoff valve in the gas supply line to allow gas to flow through the pipe. Wait a few minutes for gas to move through the gas line. DO NOT connect the dryer to LR gas service without - Electrolux EIGD55IKG | Installation Instructions - Page 15
instructions Water connection (Steam Model only} . Turn off COLD water supply to washer, 2. Remove COLD inlet hose from COLD water supply and inspect for rubber washer. Replace washer if it is torn or worn out. RUBBER WASHER MUST BEPRESENT AND UNDAMAGED J J \ COLD INLET HOSE TO WASHER - Electrolux EIGD55IKG | Installation Instructions - Page 16
instructions it another 2/3 turn with pliers. 4. Connect the COLD inlet hose for the washer to the "Y" connector and snug it by hand; then tighten it another brass water inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers. - Electrolux EIGD55IKG | Installation Instructions - Page 17
. 7. If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 8. Place these instructions in a location near the dryer for future reference. I A wiring diagram and technical data sheet are located inside - Electrolux EIGD55IKG | Installation Instructions - Page 18
Guide and enjoy your new premium dryer! If your dryer has this console: l 1 .After you plug in the dryer the first time: wake up the dryer c__-_(/IC87_7 u,353287, review the installation steps and make the necessary corrections before you attempt to use the dryer. 3.Your dryer will exit the - Electrolux EIGD55IKG | Installation Instructions - Page 19
work surface, such as top of dryer or floor near dryer, with a soft cloth or towel. 4 Be sure dryer is unplugged from power source! approximately _A"counter- clockwise and pull ring away from door. E:3 ;" 3 While supporting door with the other hand, remove 3 short, fine-thread, counter-sunk sc - Electrolux EIGD55IKG | Installation Instructions - Page 20
-thread, panhead screws. Remove 4 long, course-thread, recessed screws and hinge. Set hinge aside. \ \ 3 Install original plastic hole plugs or use new plugs supplied with dryer. - Electrolux EIGD55IKG | Installation Instructions - Page 21
E) Removing Latch Indicator Reversing Door F) Removing Hole Plug jj/J jf / _J Insert flat blade screwdriver into open slot of latch indicator. 2 Gently pry upward to release tab. 1 Insert flat blade screwdriver into open slot of hole plug. 2 Gently pry upward to release tab. 3 Pull the - Electrolux EIGD55IKG | Installation Instructions - Page 22
Reversing Door G) Reinserting Latch Indicator 1 Rotate the latch indicator and move it to the opposite hole in the door. insert indicator H) Reinserting Hole Plug 1 Rotate the hole plug and move it to the opposite hole in the door. 2 Firmly insert the two small tabs on either side of the hole plug - Electrolux EIGD55IKG | Installation Instructions - Page 23
Reversing Door I) Reattaching Latch Plate 1 Rotate latch plate and move to opposite side of door above indicator. 2 Reattach with 2 long, course-thread, counter-sunk screws. K) Reattaching Door to Front Panel 1 Use side locating pins to align hinge and install 1 short, fine-thread, counter-sunk - Electrolux EIGD55IKG | Installation Instructions - Page 24
opening in trim and reinsert. N) Reinstalling Trim Plug 1 Open door to 90 degree angle. 2 Install trim plug with 1 long, course-thread, panhead screw. O) Plug in dryer and continue operation. - Electrolux EIGD55IKG | Installation Instructions - Page 25
may order one. UNIVERSAL APPLIANCE WRENCH P/N 137019200 The matching washer to this dryer was supplied with a UNIVERSAL APPLIANCE WRENCH. If you desire another wrench, you may order one. Repmacement paAs: 1-877-4ELECTROLUX If replacements parts are needed for your dryer, contact the source where - Electrolux EIGD55IKG | Installation Instructions - Page 26
Notes
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
|nsta||ation
|nstructions
Electro[u×
Front-Load
Gas
_
Electric
DD'er
|nstrucciones
de
|nsta|acion
Secadora
e[_ctfica
y a gas
de
carga
fro_3tal
Electro[u×
Instructions
d'installation
%cheuse
_ gaz et _ l'_[ectficit_
_ chargeme_3t
fro_3tal Electro[u×