Home » Electrolux Manuals » Tools » Electrolux ES350 » Manual Viewer

Electrolux ES350 Instruction Manual

Electrolux ES350 - 16" 3.5HP ELEC Chainsaw Manual

View all Electrolux ES350 manuals

Add to My Manuals
Save this manual to your list of manuals

Electrolux ES350 manual content summary:

Electrolux ES350 | Instruction Manual - Page 1
ne pas retourner l'outil au détaillant. 1-800-554-6723 www.poulan.com Instruction Manual Manual de Instrucciones Manuel d'Instructions ES350 ES350WT ESPAÑOL WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury
Electrolux ES350 | Instruction Manual - Page 2
instructions found in this manual. off the switch, the guide bar and saw chain other parts immediately service dealer. MAINTAIN YOUR SAW IN GOOD WORKING ORDER S Have all chain saw service performed by an authorized service dealer except the items listed in the MAINTENANCE section of this manual
Electrolux ES350 | Instruction Manual - Page 3
part that is damaged should be properly repaired or replaced by an authorized service dealer unless otherwise indicated elsewhere in the instruction manual electrical shock, use extension cords specifically marked as suitable for outdoor appliances. The electrical rating of the cord must not be less
Electrolux ES350 | Instruction Manual - Page 4
occur when the moving chain contacts an object at the upper tip of the guide bar. This contact can cause the chain to dig into the object, which the chance of kickback. Follow manufacturer's chain sharpening and maintenance instructions. Check tension at regular intervals, but never with engine
Electrolux ES350 | Instruction Manual - Page 5
. Do not rely exclusively upon safety devices built into your saw. The following guide bar and chain combinations meet kickback requirements of CSA Z62.1 & Z62.3 and ANSI B175.1 when used on saws listed in this manual. Use of bar and chain combinations other than those listed is not recommended and
Electrolux ES350 | Instruction Manual - Page 6
these problems. service personnel. Replacement parts for a double insulated appliance must be identical to the parts they replace. A double insulated appliance INSTRUCTIONS ASSEMBLY WARNING: Before using chain saw, ensure all fasteners are secure. NOTE: If you need assistance or find that parts
Electrolux ES350 | Instruction Manual - Page 7
OPERATION KNOW YOUR SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future refer- ence. Bar Oil Cap Hand Guard
Electrolux ES350 | Instruction Manual - Page 8
/or discoloration of the bar. For maximum guide bar and chain life, we recommend you use until it has been repaired by an authorized service dealer. STARTING YOUR SAW 1. Connect the saw strikes a for- eign object. Inspect the saw and repair parts as necessary. S Keep the chain out of dirt and sand
Electrolux ES350 | Instruction Manual - Page 9
retreat path. S DO NOT use your saw to cut down a partially fallen tree. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn't fall completely, set saw aside and pull down tree with a cable winch, block and tackle, or tractor. CUTTING A FALLEN TREE
Electrolux ES350 | Instruction Manual - Page 10
above for cutting logs with a compression side. BUCKING USING A LOG OR SUPPORT STAND S Remember your first cut is always on the compression side of chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury
Electrolux ES350 | Instruction Manual - Page 11
WITHOUT A SUPPORT. S instructed in this manual. Various adjustments will need to be made periodically to properly maintain your unit. Improper mainte- nance may cause damage to the unit and possible injury to the operator or bystanders. CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service
Electrolux ES350 | Instruction Manual - Page 12
CHECK FOR LOOSE FASTENERS AND PARTS S Bar Clamp Nuts S Chain S Bar Adjusting Screw CHECK chain makes a sawdust powder and cuts slowly. See CHAIN SHARPENING in the SERVICE AND ADJUSTMENTS section. CHECK GUIDE BAR Conditions which require guide bar maintenance: S Saw cuts to one side or at an angle.
Electrolux ES350 | Instruction Manual - Page 13
replacement parts. The chain must comply with kickback requirements of ANSI B175.1 when tested with this saw. See your authorized service dealer guide bar groove and then into the teeth of the sprocket in the tip of the guide bar. Bar Clamp Bar Clamp Nuts Adjusting Screw 7. Hold the guide bar
Electrolux ES350 | Instruction Manual - Page 14
Secure the guide bar and bar clamp with the bar clamp nuts; tighten finger tight only. CAUTION: If saw chain is installed backwards, the saw will vibrate excessively and will not cut wood. CHAIN ADJUSTMENT See CHECK CHAIN TENSION in the MAINTENANCE section. CUSTOMER SERVICEABLE PARTS WARNING: Use
Electrolux ES350 | Instruction Manual - Page 15
dealer. Chain stops during cut. 1. Chain cutter tops not filed flat. 2. Guide bar burred or bent; rails uneven. 1. See "Chain Sharpening" in Service and Adjustments section. 2. Repair or replace guide bar. Oil inadequate for bar and chain lubrication. Chain cuts at an angle. 1. Oil tank empty
Electrolux ES350 | Instruction Manual - Page 16
for this product. This warranty does not cover parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre--delivery setup or normal adjustments explained in the instruction manual. Should you have any unanswered questions regarding