Electrolux EW30GS6CGS Installation Instructions (English, Spanish, French)
Electrolux EW30GS6CGS Manual
View all Electrolux EW30GS6CGS manuals
Add to My Manuals
Save this manual to your list of manuals |
Electrolux EW30GS6CGS manual content summary:
- Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 1
Hz. Systems) INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 2
the oven compartments before connecting the gas and electrical supply to the range. 3. Observe all governing codes and ordinances. 4. Be sure to leave these instructions with the consumer. Important Note to the Consumer Keep these instructions with your owner's guide for future reference. • As when - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 3
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS (For 4 Wire, 60 Hz. Systems) - Drill a 1/8" pilot hole . Slide range back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer. For models with a - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 4
Reinstall in reverse order making sure to level the range and check electrical connections. See pages 2 and 3 for proper anchoring instructions. Before You Call for Service Read the "Before You Call" and operating instruction sections in your Use & Care Manual. It may save you time and expense. The - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 5
PAR L'INSPECTEUR EN ÉLECTRICITÉ. LISEZ ET CONSERVEZ CES INSTRUCTIONS POUR CONSULTATION FUTURE. Dimensions et espaces libres 1. Laissez es doivent être appliquées. Les distances données sont minimales. La surface de support doit être solide et au niveau. DIMENSION HORS TOUT E LA CUIINIÈRE Porte - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 6
instructions au consommateur. Note importante au consommateur Conservez ces instructions avec votre guide ou un technicien de service qualifié. • Assurez-vous support de contre-renversement doit aussi être déplacé et installé avec la cuisinière si celle-ci est relocalisée. Des instructions - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 7
systèmes 60 Hz à 3 ou 4 fils)requis entre le bas de la cuisinière et la patte d'ajustement afin de permettre un espace pour le support. Utilisez un niveau à bulle pour vérifier vos ajustements. Glissez la cuisinière vers sa position. Vérifiez visuellement que la patte de mise à niveau arrière - Electrolux EW30GS6CGS | Installation Instructions (English, Spanish, French) - Page 8
vérifiez les raccordements électriques. Voyez les pages 2 et 3 pour les instructions correctes d'ancrage. Avant que vous ne fassiez un appel de service Lisez "Avant d'appeler" et les sections de notices d'opération de votre Guide d'utilisation et d'entretien, ils peuvent vous sauver temps et argent
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS
(For 4 Wire, 60 Hz. Systems)
1
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
p/n
316454924 (1008)
Clearances and Dimensions
1.
Provide adequate clearances between the range and adjacent combustible surfaces.
2.
Location—Check location where the range will be installed. Check for proper electrical supply, and the
stability of the floor.
3.
Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface
must be solid and level.
*30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE
BOTTOM OF AN
UNPROTECTED WOOD OR METAL CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS
PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28
MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM OR 0.020" COPPER. 0" CLEARANCE IS THE
MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO
PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE
SPACE LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE
PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A
MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
English 1-4
Français - Pages 5-8
RANGE
OVERALL
DIMENSIONS