Epson AP-60 Installation Guide

Epson AP-60 - Projector Sound Solution Manual

Get Epson AP-60 - Projector Sound Solution PDF manuals and user guides
UPC - 010343874695
View all Epson AP-60 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson AP-60 manual content summary:

  • Epson AP-60 | Installation Guide - Page 1
    AP-60 Installation Guide
  • Epson AP-60 | Installation Guide - Page 2
    , or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. Trademarks Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. General Notice: Other product names used herein are
  • Epson AP-60 | Installation Guide - Page 3
    (servicing) instructions in the literature accompanying the appliance. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install
  • Epson AP-60 | Installation Guide - Page 4
    . As a precaution, lower the volume before you turn off the system then raise it gradually after you turn it back on. • Be aware of the fact that listening to loud sound over a long period of time leads to hearing damage. • Epson accepts no responsibility for any of the components of this product
  • Epson AP-60 | Installation Guide - Page 5
    could fall down and cause injury or even death. • Do not hang from the system or the ceiling mount to avoid the risk of a falling accident. • Keep the power of the system and the projector turned off during the installation. There is a risk of an electric shock. • Be aware of the neck strap when
  • Epson AP-60 | Installation Guide - Page 6
    should be installed by a professional audio/video installer or other qualified professional. Epson cannot provide advice concerning construction practices or building codes in your area. • Prior to installing this product, read the installation instructions completely. Keep these instructions in an
  • Epson AP-60 | Installation Guide - Page 7
    heat. • Do not install this product on a system components as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. • Except as specifically explained in these instructions, do not attempt to service
  • Epson AP-60 | Installation Guide - Page 8
    Contents Introduction 9 Planning the Installation 10 Installing the IR Dome Sensor 11 Install the Mounting Pipe 13 Install the AP-60 14 Install the Projector 19 Attach the Neck Strap 19 Insert Batteries 20 Adjust the Sound 21 Solving Problems 23 Where To Get Help 26 8
  • Epson AP-60 | Installation Guide - Page 9
    all wiring required for the audio and power connections for the AP-60 and projector. • If you have a projector already installed, remove the projector from the 1.5-inch mounting pipe and remove the old mounting pipe. If you aren't installing a projector with the AP-60, make sure you have a ceiling
  • Epson AP-60 | Installation Guide - Page 10
    to install the AP-60. Allow at least 1 to 2 hours to complete the installation. Be sure to read all of the installation instructions before starting. Note Epson strongly recommends that the AP-60 be installed by a professional audio/video installer or other qualified professional. Epson cannot
  • Epson AP-60 | Installation Guide - Page 11
    AP-60 should be installed by a professional audio/video installer or other qualified professional. To install the system, the installer will cover of the IR dome sensor. • The use of IR remote controls of any kind can interrupt the sound or cause noise. • The IR dome sensor receives reflected
  • Epson AP-60 | Installation Guide - Page 12
    • Coaxial cable Warning Make sure that the ceiling is strong enough to support the IR dome sensor and coaxial cable. Epson accepts no responsibility for the IR dome sensor falling due to insufficient ceiling strength or inadequate installation. 1 Bend both ends of the mounting bracket as shown below
  • Epson AP-60 | Installation Guide - Page 13
    your projector. If you're installing the AP-60 without a projector, the ceiling mount must be designed to support the total weight of the AP-60 (approximately 15.2 lbs [6.9 kg]). 1 Thread the included mounting pipe into your ceiling mount. 2 Follow your ceiling mount manufacturer's instructions to
  • Epson AP-60 | Installation Guide - Page 14
    nut and have them close by. 2 Before attaching the AP-60 to the mounting pipe, feed the projector's power and video cables through the cable channel as shown below. 3 Slide the AP-60 and the lower bracket onto the mounting pipe with the audio control panel facing the front of the room. The lower
  • Epson AP-60 | Installation Guide - Page 15
    two screws from the audio control panel. Remove screws 6 Gently remove the audio control panel from the AP-60 and keep it supported at all times. Warning Pulling out the audio control panel too quickly or not supporting the audio control panel when it is removed from the AP-60 can permanently damage
  • Epson AP-60 | Installation Guide - Page 16
    / On Line 1 L LCP R Output Rec CMD Microphone IR sensor RS232 Line 2 DVD 3.5 mm stereo-mini jack input 3.5 mm stereo-mini jack output 9 Gently slide the audio control panel back into the AP-60 while pulling out any excess cable from the top of the unit. 16
  • Epson AP-60 | Installation Guide - Page 17
    10 Secure the two screws that hold the audio control panel in place. 11 Attach the IR dome sensor cable to the top of the AP-60. 12 Once the cables are positioned as desired, lift the AP-60 and secure the lower bracket with the M10 bolt and nut. 13 Tighten the M47.5 jam nut until
  • Epson AP-60 | Installation Guide - Page 18
    14 Attach the included guy wires to the AP-60 as shown below. 15 Attach the guy wires to a secure location. Installation varies depending on your building construction. Note When installing the guy wires, do not make them too taut. This can cause the AP-60 to be unstable on the mounting pipe and
  • Epson AP-60 | Installation Guide - Page 19
    the Projector When installing a projector under the AP-60, make sure that all of the mounting hardware and guy wires are secured correctly. Follow the instructions included with your projector mount to attach the projector to the mounting pipe. Then connect power and video cables to the projector as
  • Epson AP-60 | Installation Guide - Page 20
    3 Reconnect the ends of the neck strap. Insert Batteries 1 Remove the remote control battery cover. 2 Check the battery label and insert the included R6 (manganese) AA batteries into the remote control. 3 Replace the remote control battery cover. 4 Open the pendant microphone's battery cover. 20
  • Epson AP-60 | Installation Guide - Page 21
    the Sound Before adjusting the audio levels, make sure that you have connected your audio equipment to the AP-60. Then follow the steps in this sections to adjust the audio levels. 1 Press the P power button on the AP-60 remote control to turn on the system. The P power light on the AP-60 turns
  • Epson AP-60 | Installation Guide - Page 22
    Set to Channel 1 7 Press the power button until it clicks into place. The power button turns green. Power button 8 Verify that the Mic 1 light on AP-60 is lit. 9 Adjust the Gain wheel until the white line on the is next to Up, but still visible. White line 22
  • Epson AP-60 | Installation Guide - Page 23
    where the speaker will be standing. Solving Problems If you're having a problem with the AP-60, check for a solution in one of these sections: • "Basic Operation Problems"below • "Sound Problems" on page 24 • "Problems Using the Pendant Microphone" on page 25 • "Problems Using the Remote Control" on
  • Epson AP-60 | Installation Guide - Page 24
    on. The remote control doesn't work. See "Problems Using the Remote Control" on page 25. There is no sound. See "Sound Problems" on page 24. Sound Problems Problem Solution There is no sound. Make sure the AP-60 is turned on. If the AP-60 doesn't receive an audio signal for 60 minutes, it
  • Epson AP-60 | Installation Guide - Page 25
    volume of the external audio device. Problems Using the Remote Control Problem Solution The system doesn't respond to the remote control. Make sure you're within about 20 feet of the AP-60. Point the remote control toward the AP-60. You may need to replace the remote control's batteries (see
  • Epson AP-60 | Installation Guide - Page 26
    ready: • Product name (AP-60) and serial number (located on the back of the product) • Proof of purchase (such as a store receipt) and date of purchase • Description of the problem, including computer, audio, or video configuration Purchase Accessories You can purchase projectors, screens, or other
  • Epson AP-60 | Installation Guide - Page 27
  • Epson AP-60 | Installation Guide - Page 28
    Printed in XXX
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
AP-60
Installation Guide