Epson ActionLaser 1000 Product Support Bulletin(s)

Epson ActionLaser 1000 Manual

Get Epson ActionLaser 1000 PDF manuals and user guides View all Epson ActionLaser 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson ActionLaser 1000 manual content summary:

  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 1
    CONTINUE. After the instructions to replace the imaging cartridge (as shown on pages 3-29 through 3-32 of the ActionLaser 1000/1500 Reference Guide) has been followed, some printers may continue to display the above messages. This condition does not affect printer operation or print quality in any
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 2
    . While holding down the CONTINUE (v) button, press the INITIALIZE / RESET(q) button until the READY message appears. 7. Repeat Steps 1 through 3 to print a new status sheet. The Toner Remaining message printed on the status sheet should now be E * * * * *F. If it is not, repeat steps 4 through 7.
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 3
    the Epson printer line? A. Both. The ActionLaser 1000 replaces the ActionLaser II. The ActionLaser 1500 is an addition to the Epson printer line. 3. Q. What ate the major advantages of the ActionLaser 1000 over the ActionLaser II? A. The ActionLaser 1000 is a completely new laser printer, utilizing
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 4
    1000 and the ActionLaser 1500? A. Yes. The ActionLaser 1000 and ActionLaser 1500 printers accept one of the following user installed interfaces: buffered serial, buffered parallel, AppleTalk, twinax and coax interfaces. 5. Q. Do the ActionLaser 1000 and ActionLaser 1500 use the same toner cartridge
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 5
    parallel and serial ports and can be shared by two computers. A type 'B" interface may also be installed in the printer for additional printer sharing capabilities. 9. Q. Can the ActionLaser 1000 and ActionLaser 1500 connect to IBM System 3x, AS-400 systems or to 3270 series terminals? A. Yes. Using
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 6
    with the ActionLaser 1000 and ActionLaser 1500? A. Yes. The Epson AppleTalk interface and PostScript options allow the new ActionLasers to be connected directly to a LocalTalk* network, or directly to an Apple Macintosh computer. 15. Q. What is MicroArt printing? A. MicroArt printing uses toner with
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 7
    work with the ActionLaser 1000 and ActionLaser 1500? A. The ActionLaser 1500 comes standard with parallel and serial interfaces, allowing two users to share a single printer. By installing an optional third interface, three users can share the printer. The ActionLaser 1000 supports a single user
  • Epson ActionLaser 1000 | Product Support Bulletin(s) - Page 8
    PSB No: P-0095A Page: 6 of 6 21. Q. What printer driver selection should I choose in my software programs when using the ActionLaser 1000 and ActionLaser 1500 in the HP mode? A. The proper printer driver selections are listed below in order of preference. HP LaserJet lllsi HP LaserJet IIIP HP
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
EPSON AMERICA INC.
EPSON
Product Support Bulletin
Subject: New ActionLaser 1000/1500 Imaging Cartridge Replacement Procedure
Date: 6/4/93
PSB No: P-0100
Page(s): 1 of 2
Originator: LHT
This bulletin provides supplemental information to resolve a situation when printed
images become faint, SelecType Level 2 TONER message indicating that the
toner amount is low (E*
F), and three messages flash in rotation on the LCD:
NEW CARTRIDGE?
YES, PRESS RESET
NO, PRESS CONTINUE.
After the instructions to replace the imaging cartridge (as shown on pages 3-29
through 3-32 of the ActionLaser 1000/1500 Reference Guide) has been followed,
some printers may continue to display the above messages.
This condition does
not affect printer operation or print quality in any way.
It can be corrected by
resetting the printer as described below:
NOTE:
Resetting clears all the saved SelecType information but the status
sheet printed in step 3 shows the current settings.
1. Press the LEVEL 1 button to enter SelecType Level 1.
2. Press CONTINUE
(v)
button until
STATUS SHEET
appears on the display.
3. Press INITIALIZE
/
RESET
(b)
button twice to print a status sheet.
4. Save the status sheet for future reference, then turn off the printer.
5. Press and hold down the ON LINE, CONTINUE
(v),
and FEED
(b)
buttons
while you turn on the printer and keep pressing the buttons until the following
message appears:
STARTUP ERROR LT<>A4
When the above message appears, release the buttons.