Epson ActionLaser 1500 Product Support Bulletin(s)

Epson ActionLaser 1500 Manual

Get Epson ActionLaser 1500 PDF manuals and user guides View all Epson ActionLaser 1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson ActionLaser 1500 manual content summary:

  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 1
    Product Support Bulletin EPSON Subject: New ActionLaser 1000/1500 Imaging Cartridge Replacement Procedure Date: 6/4/93 Page(s): 1 of 2 PSB No: P-0100 Originator: LHT This bulletin provides supplemental information to resolve a situation when printed images become faint, SelecType Level 2 TONER
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 2
    . While holding down the CONTINUE (v) button, press the INITIALIZE / RESET(q) button until the READY message appears. 7. Repeat Steps 1 through 3 to print a new status sheet. The Toner Remaining message printed on the status sheet should now be E * * * * *F. If it is not, repeat steps 4 through 7.
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 3
    image improvement technology, 14 bit-mapped /13 scalable fonts, a serial and a parallel port, and 1 Mb of memory. 2. Q. Are these new ActionLaser printers additions to or replacements to the Epson printer line? A. Both. The ActionLaser 1000 replaces the ActionLaser II. The ActionLaser 1500 is
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 4
    and ActionLaser 1500 use the same toner cartridge as the ActionLaser II? A. No. The ActionLaser 1000 and 1500 use a new all-in-one imaging cartridge. The imaging cartridge comes packed in the box with the printer. 6. Q. Do the ActionLaser 1000 and ActionLaser 1500 use the same imaging cartridge as
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 5
    parallel and serial ports and can be shared by two computers. A type 'B" interface may also be installed in the printer for additional printer sharing capabilities. 9. Q. Can the ActionLaser 1000 and ActionLaser 1500 connect to IBM System 3x, AS-400 systems or to 3270 series terminals? A. Yes. Using
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 6
    effect" (a printer error that causes edges to be darker than the center portion of an image), and less toner blurring. 16. Q. What is R/Tech? A. Resolution Improvement Technology (RITech) allows the ActionLaser 1500 to reassemble the dot mapped data to improve the printed image. This improvement
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 7
    work with the ActionLaser 1000 and ActionLaser 1500? A. The ActionLaser 1500 comes standard with parallel and serial interfaces, allowing two users to share a single printer. By installing an optional third interface, three users can share the printer. The ActionLaser 1000 supports a single user
  • Epson ActionLaser 1500 | Product Support Bulletin(s) - Page 8
    1000 and ActionLaser 1500? A. Listed below are the product codes of the options and supplies: Part Number C812301 C812311 S051011 C826021 C823071 C823101 C826051 512KBMEM 2MBMEM MACLP C823151 C823141 Description Lower Paper Cassette Tray Face-up Output Tray Imaging Cartridge Epson GL Identity
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
EPSON AMERICA INC.
EPSON
Product Support Bulletin
Subject: New ActionLaser 1000/1500 Imaging Cartridge Replacement Procedure
Date: 6/4/93
PSB No: P-0100
Page(s): 1 of 2
Originator: LHT
This bulletin provides supplemental information to resolve a situation when printed
images become faint, SelecType Level 2 TONER message indicating that the
toner amount is low (E*
F), and three messages flash in rotation on the LCD:
NEW CARTRIDGE?
YES, PRESS RESET
NO, PRESS CONTINUE.
After the instructions to replace the imaging cartridge (as shown on pages 3-29
through 3-32 of the ActionLaser 1000/1500 Reference Guide) has been followed,
some printers may continue to display the above messages.
This condition does
not affect printer operation or print quality in any way.
It can be corrected by
resetting the printer as described below:
NOTE:
Resetting clears all the saved SelecType information but the status
sheet printed in step 3 shows the current settings.
1. Press the LEVEL 1 button to enter SelecType Level 1.
2. Press CONTINUE
(v)
button until
STATUS SHEET
appears on the display.
3. Press INITIALIZE
/
RESET
(b)
button twice to print a status sheet.
4. Save the status sheet for future reference, then turn off the printer.
5. Press and hold down the ON LINE, CONTINUE
(v),
and FEED
(b)
buttons
while you turn on the printer and keep pressing the buttons until the following
message appears:
STARTUP ERROR LT<>A4
When the above message appears, release the buttons.