Epson B134101 Installation Manual

Epson B134101 - DM D210 - Vacuum Fluorescent Display Character Manual

Get Epson B134101 - DM D210 - Vacuum Fluorescent Display Character PDF manuals and user guides View all Epson B134101 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson B134101 manual content summary:

  • Epson B134101 | Installation Manual - Page 1
    English Customer Display DM-D210 Installation Manual 401285101
  • Epson B134101 | Installation Manual - Page 2
    to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. ❏ Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those
  • Epson B134101 | Installation Manual - Page 3
    , or unusual noise. Continued use may lead to fire or electric shock. Immediately turn the power off and contact your dealer or a SEIKO EPSON service center for advice. ❏ Never attempt to repair this product yourself. Improper repair work can be dangerous. Tampering with this product may result in
  • Epson B134101 | Installation Manual - Page 4
    the instruction in this manual. Wrong if it falls. ❏ Do not attach plural extension supports. Product may be damaged or cause injury if it Product Name: DM-D210 Type Name: M59DB The following standards are is so labeled. (EMC is tested using the EPSON PS-170 power supply.) ❏ Europe: CE Marking Safety
  • Epson B134101 | Installation Manual - Page 5
    that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment. energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
  • Epson B134101 | Installation Manual - Page 6
    Attaching to the TM-H6000/TM-U675 15 Attaching to Other TM Printers 20 Attaching to the DM-D stand 23 Part Names and Functions 30 Exterior 30 DIP Switch 31 DIP Switch Functions 31 Turning and Tilting the DM-D210 33 Self Test 34 Check Items of Self test 34 Performing Self
  • Epson B134101 | Installation Manual - Page 7
    that are unstable or are subject to high levels of vibration. ❏ When connecting or disconnecting cables, make sure that the power switch of the DM-D210 and printers connected to the DMD210 are turned off. ❏ Do not drop the DM
  • Epson B134101 | Installation Manual - Page 8
    .) ❏ TM-H6000/TM-U675. You can attach the DM-D210 to TM-H6000/ TM-U675 printers using the "DM-D pole unit for TM printers (Type A)" (DP-502). (See page 15.) ❏ Other TM printers. You can attach the DM-D210 using the "DM-D pole unit for TM printers (Type A)" (DP-502) and Velcro tapes or screws. (See
  • Epson B134101 | Installation Manual - Page 9
    " (DP-504). base fixing screws support A support B (for extension) Assembling steps 1. Pass the cable for the DM-D210 through support A, and attach support A to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support A until you feel it click. When
  • Epson B134101 | Installation Manual - Page 10
    the screws. Note: When attaching the base, note that the corners of the base are set as shown below. 3. Pass the cable for the DM-D210 through the base. 4. Insert the tab on the base into the hole on the
  • Epson B134101 | Installation Manual - Page 11
    printers using the "DM-D pole unit for TM printers (Type B)" (DP-503). Required items The following items are used to attach the DM-D210 to the TM-H5000II/TM-J8000 printers. These items are packed with the "DM-D pole unit for TM printers (Type B)" (DP-503). base support C fixing screws support
  • Epson B134101 | Installation Manual - Page 12
    for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2. Attach the base to the setting position on the TM printer and secure it
  • Epson B134101 | Installation Manual - Page 13
    English 3. Pass the cable for the DM-D210 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D210 to the DM connector on the TM printer. 11
  • Epson B134101 | Installation Manual - Page 14
    (Type A)" (DP-502). Required items The following items are used to attach the DM-D210 to the TM-U375/ TM-U950 printers. These items are packed with the "DM-D pole unit for TM printers (Type A)" (DP-502). rubber feet rubber feet (square) (large) rubber feet (square
  • Epson B134101 | Installation Manual - Page 15
    1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the rubber feet to the printer. When using support B for extension [TM-U375] [TM
  • Epson B134101 | Installation Manual - Page 16
    3. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D210 to the DM connector on the TM printer. 5. Adjust the length of the cable and secure fixing plate A to the printer with screws. [TM-U375
  • Epson B134101 | Installation Manual - Page 17
    6. Store any excess cable in the support, and attach the DM-D210 to fixing plate A. English Attaching to the TM-H6000/TM-U675 The DM-D210 can be attached directly to the TM-H6000/TM-U675 printers using the "DM-D pole unit for TM printers (Type A)" (DP-502). You can attach fixing plate A on either
  • Epson B134101 | Installation Manual - Page 18
    DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2. Attach the rubber feet to the printer. 3. Attach fixing plate B to the printer. 16
  • Epson B134101 | Installation Manual - Page 19
    fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable for the DM-D210 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing
  • Epson B134101 | Installation Manual - Page 20
    7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw. 18
  • Epson B134101 | Installation Manual - Page 21
    the display, make sure that you can open the paper roll cover. paper roll cover 8. Store any excess cable in the support and attach the DM-D210 to fixing plate A. 9. Connect the power cable of the printer. To avoid disconnection, hook the cable to the tabs on fixing plate B, as shown below. 19
  • Epson B134101 | Installation Manual - Page 22
    items are used when the DM-D210 is used with other TM printers. These items are packed with the "DM-D pole unit for TM printers (Type A)" (DP-502). fixing plate A Velcro tapes Velcro tapes fixing screws for wood position support C support B (for extension) Assembling steps using Velcro
  • Epson B134101 | Installation Manual - Page 23
    on support B into the hole on support C until you feel it click. When using support B for extension 3. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D210 to the DC connector on the TM printer. 21
  • Epson B134101 | Installation Manual - Page 24
    5. Store any excess cable in the support, and attach the DM-D210 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. using Velcro tapes." 2. Secure fixing plate A to the setting position with fixing screws. 3. Attach the DM-D210 to fixing plate A. 22
  • Epson B134101 | Installation Manual - Page 25
    "DM-D stand unit for DM Customer Display " (DP-210). The DM-D210 with the DM-D stand can be connected to a TM printer, or be used as a stand alone product. Required items The following items are used to attach the DM-D210 to the DM-D stand. Note that an optional power unit (PS-170
  • Epson B134101 | Installation Manual - Page 26
    Connectors for the DM-D stand The connectors for the DM-D stand are as follows: computer connector display connector printer connector power supply unit connector extension cable connector Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable
  • Epson B134101 | Installation Manual - Page 27
    Contents Set the jumpers as in the left columns when connecting both the TM printer and the DM-D stand. (Default setting) Set the jumpers as in the left column avoid damage to the DM-D210 and the power supply unit, make sure to note the following points. ❏ Use the optional Seiko Epson products, PS-170, or
  • Epson B134101 | Installation Manual - Page 28
    Assembling steps 1. Pass the cable for the DM-D210 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support to the DM-D stand. When using the extension support 2. Insert the tab on the DM-D210 (or the extension support) into the hole on the DM-D stand until
  • Epson B134101 | Installation Manual - Page 29
    English 3. Connect the cable for the DM-D210 to the display connector on the DM-D stand until you feel it click. 4. Connect one end of the computer interface cable to the computer connector
  • Epson B134101 | Installation Manual - Page 30
    When using as a stand alone, go to step 6. When using with the printer, connect one end of the printer interface cable for the printer to the printer connector on the DM-D stand; then connect the other end to the connector on the printer. Tighten the screws on both ends of the cable to fasten them
  • Epson B134101 | Installation Manual - Page 31
    , set the jumpers. (See "Jumper setting" on page 25.) 9. Arrange the cables as shown below. Put the cables for the DM-D210 inside the DM-D stand. 10. When the extension support is used, attach Velcro tapes to the four corners of the plate to avoid falling down. 11. Connect the cord of
  • Epson B134101 | Installation Manual - Page 32
    ) DIP switch (bottom of the display) ❏ Display: Characters are displayed. ❏ Power switch: The power is turned on/off. ❏ DIP switch: The functions of the DM-D210 are changed. (See "DIP switch" for details.) Note: When turning on the DM
  • Epson B134101 | Installation Manual - Page 33
    English DIP Switch DIP Switch Functions The DM-D210 has one DIP switch. The functions of the DIP switche are as follows: DIP switch 1 DSW1 No. 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 Function Data receive error Data length Parity on
  • Epson B134101 | Installation Manual - Page 34
    while removing the DIP switch cover to prevent electrical damage to the DM-D210. 1. Turn off the power for the DM-D210. 2. Remove the DIP switch cover. DIP switch cover 3. Change each setting of the switches with a pointed object, such as a pen tip or small screwdriver. 4. Close
  • Epson B134101 | Installation Manual - Page 35
    Tilting the DM-D210 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the "DM-D pole unit for IR" (DP-504) and the "DM-D pole unit for TM printers
  • Epson B134101 | Installation Manual - Page 36
    , such as brightness, flashing, and scroll Performing Self test To perform the self test, follow the steps below. 1. Turn off the power for the DM-D210. 2. Set the SW 1-8 of the DIP switch to ON, and turn on the power. Note: If the contents of the self test are not displayed
  • Epson B134101 | Installation Manual - Page 37
    English Specification General Specifications ❏ Height, Width, Depth and Weight 260mm 83mm 503mm 158mm 38mm 110mm DM-D Stand (DP-210) 260mm 35
  • Epson B134101 | Installation Manual - Page 38
    • DM-D210: Height: Width: Depth: Weight: • DM-D stand (DP-501): Height: Width: Depth: Weight: 91 mm 260 mm 50.5 mm 600 g 53 mm 260 mm 110 mm 385 g DM-D pole unit for IR (DP-504) DM-D pole unit for TM printer (Type B) (DP-503) DM-D pole unit for TM printers (Type
  • Epson B134101 | Installation Manual - Page 39
    (Type B)" (DP-503): Height: 248 mm Width: 50 mm Depth: 53 mm Weight: 116 g • Fixing plate A and support C of the "DM-D pole unit for TM printers (Type A)" (DP-502): Height: 260 mm Width: 78 mm Depth: 164 mm Weight: 264 g ❏ Tilt angle Max 36° (3 steps, 4 positions) ❏ Horizontal
  • Epson B134101 | Installation Manual - Page 40
    Electrical Specifications ❏ Type PS-170, PA-6508, PB-6509, PB-6510, PA-6511, PA-6513 (when using the DM-D stand) ❏ Rated voltage DC 11.4 to 48 V ❏ Rated current 0.4 A (max.) Environmental Specifications ❏ Operation environment Temperature: 5°C to 40°C Humidity: 30% to 85% (No condensation) ❏
  • Epson B134101 | Installation Manual - Page 41
    English Character Specifications ❏ Type of character • Alphanumeric characters: 95 • International characters: 37 • Extended graphics: 128 characters × 12 pages ❏ Character grid • Font : • Character size • Character pitch 5 × 7 dot, comma, period, annunciator 3.5 mm x 5.0 mm 9.9 mm
  • Epson B134101 | Installation Manual - Page 42
    ❏ 40
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
Customer Display
DM-D210
Installation Manual
/
設置マニュアル / 安裝手冊
401285101
English