Epson DM-D110 Installation Manual

Epson DM-D110 - Vacuum Fluorescent Display Character Manual

Get Epson DM-D110 - Vacuum Fluorescent Display Character PDF manuals and user guides View all Epson DM-D110 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson DM-D110 manual content summary:

  • Epson DM-D110 | Installation Manual - Page 1
    English Customer Display DM-D110 Installation Manual 401285001
  • Epson DM-D110 | Installation Manual - Page 2
    to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. ❏ Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those
  • Epson DM-D110 | Installation Manual - Page 3
    carefully, and store it in an accessible location near your installation. Precaution Headings This document uses the two headings shown below to fire or electric shock. Immediately turn the power off and contact your dealer or a SEIKO EPSON service center for advice. ❏ Never attempt to repair this
  • Epson DM-D110 | Installation Manual - Page 4
    CAUTION: ❏ Do not plug the cable differently from the instruction in this manual. Wrong connection may cause equipment damage and Name: DM-D110 Type Name: M58DB The following standards are applied only to the display that is so labeled. (EMC is tested using the EPSON PS-170 power supply.) ❏
  • Epson DM-D110 | Installation Manual - Page 5
    not expressly approved by SEIKO EPSON Corporation could void your authority energy and, if not installed and used in accordance with the instruction manual, may cause harmful conforme à la norme NMB-003 du Canada. About This Manual Cautions and Notes CAUTION: Cautions must be observed to avoid
  • Epson DM-D110 | Installation Manual - Page 6
    to the TM-H6000/TM-U675 15 Attaching to Other TM Printers 20 Attaching to the DM-D stand 23 Part Names and Functions 31 Exterior 31 DIP Switch 32 DIP Switch Functions 32 Turning and Tilting the DM-D110 34 Self Test 35 Check Items of Self test 35 Performing Self test 35 Diagnostics 35
  • Epson DM-D110 | Installation Manual - Page 7
    that are unstable or are subject to high levels of vibration. ❏ When connecting or disconnecting cables, make sure that the power switch of the DM-D110 and printers connected to the DM-D110 are turned off. ❏ Do not drop the DM-D110, because you may damage the built-in vacuum fluorescent display. 5
  • Epson DM-D110 | Installation Manual - Page 8
    . You can attach the DM-D110 to the DM-D stand directly using the "DM-D stand unit for DM Customer Display" (DP-110). When using the DM-D stand, an optional power supply unit (PS-170) is required. Also, if you want to extend the length of the DM-D110, an optional extension support unit (DP-105) is
  • Epson DM-D110 | Installation Manual - Page 9
    to attach the DM-D110 to the IM series. These items are packed with the "DM-D pole unit for IR" (DP-504). base fixing screws support A support B (for extension) Assembling steps 1. Pass the cable for the DM-D110 through support A, and attach support A to the DM-D110. When using support B for
  • Epson DM-D110 | Installation Manual - Page 10
    the setting position on the IM series, and secure it with the screws. Note: When attaching the base, note that the corners of the base are set as shown below. 3. Pass the cable for the DM-D110 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. . 8
  • Epson DM-D110 | Installation Manual - Page 11
    cable for the DM-D110 to the DM connector on the IM series. Attaching to the TM-H5000II/TM-J8000 The DM-D110 can be attached directly to the TM-H5000II/TM-J8000 printers using the "DM-D pole unit for TM printers (Type B)" (DP-503). Required items The following items are used to attach the DM-D110
  • Epson DM-D110 | Installation Manual - Page 12
    Assembling steps 1. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2. Attach the base to the setting position
  • Epson DM-D110 | Installation Manual - Page 13
    English 3. Pass the cable for the DM-D110 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D110 to the DM connector on the TM printer. 11
  • Epson DM-D110 | Installation Manual - Page 14
    DP-502). Required items The following items are used to attach the DM-D110 to the TM-U375/ TM-U950 printers. These items are packed with the "DM-D pole unit for TM printers (Type A)" (DP-502).
  • Epson DM-D110 | Installation Manual - Page 15
    English Assembling steps 1. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2. Attach the rubber feet to the
  • Epson DM-D110 | Installation Manual - Page 16
    3. Pass the cable for the DM-D110 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D110 to the DM connector on the TM printer. 5. Adjust the length of the cable and secure fixing plate A to the printer with screws. [TM-U375] 14 [
  • Epson DM-D110 | Installation Manual - Page 17
    6. Store any excess cable in the support, and attach the DM-D110 to fixing plate A. English Attaching to the TM-H6000/TM-U675 The DM-D110 can be attached directly to the TM-H6000/TM-U675 printers using the "DM-D pole unit for TM printers (Type A)" (DP-502). You can attach fixing plate A on either
  • Epson DM-D110 | Installation Manual - Page 18
    Assembling steps 1. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2. Attach the rubber feet to the printer.
  • Epson DM-D110 | Installation Manual - Page 19
    through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable for the DM-D110 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the
  • Epson DM-D110 | Installation Manual - Page 20
    7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw. 18
  • Epson DM-D110 | Installation Manual - Page 21
    open if the position of the display is inappropriate. Before securing the position of the display, make sure that you can open the paper roll cover. paper roll cover 8. Store any excess cable in the support and attach the DM-D110 to fixing plate A. 9. Connect the power cable of the printer. To avoid
  • Epson DM-D110 | Installation Manual - Page 22
    The following items are used when the DM-D110 is used with other TM printers. These items are packed with the "DM-D pole unit for TM printers (Type A)" (DP-502). fixing plate A Velcro tapes Velcro tapes fixing screws for wood position support C support B (for extension) Assembling steps using
  • Epson DM-D110 | Installation Manual - Page 23
    English 2. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 3. Pass the cable for the DM-D110 through the hole
  • Epson DM-D110 | Installation Manual - Page 24
    5. Store any excess cable in the support, and attach the DM-D110 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follow steps 2 and 3 in "Assembling steps using Velcro tapes." 2. Secure fixing plate A to the setting
  • Epson DM-D110 | Installation Manual - Page 25
    length of the DM-D110. Please get them separately from the DM-D stand unit (DP-501). DM-D stand base plate extension cable for power supply RS-232C connector installation screw (mm type)
  • Epson DM-D110 | Installation Manual - Page 26
    for the DM-D stand The connectors for the DM-D stand are as follows: computer connector display connector printer connector power supply unit connector extension cable connector Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable to the
  • Epson DM-D110 | Installation Manual - Page 27
    to the DM-D110 and the power supply unit, make sure to note the following points. ❏ Use the optional Seiko Epson products, PS-170, or PA-6508, PA-6511, PA-6513, PB-6509 or PB-6510 as the power supply. ❏ Never connect the DC cable to the power supply unit when the power supply unit is connected
  • Epson DM-D110 | Installation Manual - Page 28
    1. Pass the cable for the DM-D110 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support (DP-105) to the DM-D stand. When using the extension support (DP-105) 2. Insert the tab on the DM-D110 (or the extension support) into the hole on the DM-D stand until
  • Epson DM-D110 | Installation Manual - Page 29
    English 3. Connect the cable for the DM-D110 to the display connector on the DM-D stand until you feel it click. 4. Connect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer. Tighten the screws on
  • Epson DM-D110 | Installation Manual - Page 30
    fasten them. printer 6. When not using the extension cable for power supply packed with the DM-D stand, go to step 7. When using the extension cable, connect it (with the arrow mark up) to the extension cable connector indicated with "POWER OUT" on the DM-D stand; then connect the other end to the
  • Epson DM-D110 | Installation Manual - Page 31
    supply unit connector indicated with "POWER IN" on the DM-D stand. power supply unit connector DC cable of power supply unit 8. When using as a stand alone product, set the jumpers. (See "Jumper setting" on page 25.) 9. Arrange the cables as shown below. Put the cables for the DM-D110 inside the DM
  • Epson DM-D110 | Installation Manual - Page 32
    following the number of the arrow shown below. At this time, push the base plate until it is locked by the hook on the DM-D stand. 11. When the extension support (DP-105) is used, attach Velcro tapes to the four corners of the plate to avoid falling down. 12. Connect the cord
  • Epson DM-D110 | Installation Manual - Page 33
    Part Names and Functions Exterior display DIP switch (rear side of the display) power switch (bottom of the display) ❏ Display: Characters are displayed. ❏ Power switch: The power is turned on/off. ❏ DIP switch: The functions of the DM-D110 are changed. (See "DIP switch" for details.) Note: When
  • Epson DM-D110 | Installation Manual - Page 34
    The DM-D110 has one DIP switch. The functions of the DIP switch are as follows: DIP switch 1 DSW1 No. 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 Function Data receive error Data length Parity on or off Parity type Change transmission speed Self test selection (*) ON Ignored 7 bits Parity Even OFF Displays
  • Epson DM-D110 | Installation Manual - Page 35
    English Setting the DIP switches CAUTION: Turn off the DM-D110 while removing the DIP switch cover to prevent electrical damage to the DM-D110. 1. Turn off the power for the DM-D110. 2. Remove the DIP switch cover. DIP switch cover 3. Change each setting of the switches with a pointed object, such
  • Epson DM-D110 | Installation Manual - Page 36
    Turning and Tilting the DM-D110 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the "DM-D pole unit for IR" (DP-504) and the "DM-D pole unit for TM printers (Type
  • Epson DM-D110 | Installation Manual - Page 37
    , such as brightness, flashing, and scroll Performing Self test To perform the self test, follow the steps below. 1. Turn off the power for the DM-D110. 2. Set the SW 1-8 of the DIP switch to ON, and turn on the power. Note: If the contents of the self test are not displayed, the DM-D110 may be
  • Epson DM-D110 | Installation Manual - Page 38
    Specification General Specifications ❏ Height, Width, Depth and Weight   DM-D110     DM-D stand (DP-110) • DM-D110: Height: Width: Depth: Weight: • DM-D stand (DP-501): Height: Width: Depth: Weight: 69 mm 165 mm 50.5 mm 285 g 63 mm 165 mm 110 mm 385
  • Epson DM-D110 | Installation Manual - Page 39
    (Type A) (DP-502) 129 mm 248 mm 260 mm 50 mm base 78 mm 164 mm 53 mm • Base and support A of the "DM-D pole unit for IR" (DP-504): Height: 129 mm Width: 50 mm Depth: 53 mm Weight: 60 g • Base and support C of the "DM-D pole unit for TM printers (Type B)" (DP-503): Height: 248
  • Epson DM-D110 | Installation Manual - Page 40
    Number of characters: 20 column × 2 lines max. • Display color: • Brightness: Green (505 nm) 690 (cd/m2) Electrical Specifications ❏ Type PS-170, PA-6508, PB-6509, PB-6510, PA-6511, PA-6513 (when using the DM-D stand) ❏ Rated voltage DC 11.4 to 48 V ❏ Rated current 0.2 A (max.) Environmental
  • Epson DM-D110 | Installation Manual - Page 41
    characters: 37 • Extended graphics: 128 characters × 12 pages ❏ Character grid • Font : • Character size • Character pitch 5 × 7 dot, cursor 3.5 mm x 5.0 mm 5.2 mm Reliability Specification ❏ MTBF (vacuum fluorescent display only) 20,000 hours (a half-value period of the brightness) 39
  • Epson DM-D110 | Installation Manual - Page 42
    40
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
Customer Display
DM-D110
Installation Manual
/
設置マニュアル / 安裝手冊
401285001
English