Epson EX3210 Quick Setup

Epson EX3210 Manual

Get Epson EX3210 PDF manuals and user guides View all Epson EX3210 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson EX3210 manual content summary:

  • Epson EX3210 | Quick Setup - Page 1
    online User's Guide. Note: These illustrations show the EX5210/EX7210, but the instructions are the same for the EX3210 unless otherwise noted. Connect the projector Choose from the following connections. See the sections below or the online User's Guide for details. Computer USB cable HDMI cable
  • Epson EX3210 | Quick Setup - Page 2
    on and off Choose which source to display Access projector menus Navigate projector menus Turn off projector display Get solutions to common problems For more information on using the remote control, see the online User's Guide. Troubleshooting If you see a blank screen or the No signal
  • Epson EX3210 | Quick Setup - Page 3
    . Mac OS® X 10.5.1 ou version ultérieure : Après avoir mis le projecteur sous tension, le dossier de configuration pour USB Display s'affiche dans le Finder. Double-cliquez sur USB Display Installer et suivez les directives à l'écran pour installer le logiciel Epson USB Display (seulement
  • Epson EX3210 | Quick Setup - Page 4
    ). Si vous n'avez pas d'icône pour le Guide de l'utilisateur, vous pouvez l'installer à partir du CD ou aller sur le site Web d'Epson, tel que décrit dans la section ci-dessous. Services de soutien téléphonique Pour utiliser l'assistance technique Epson PrivateLine®, composez le 1 800 637-7661 et
  • 1
  • 2
  • 3
  • 4
Quick Setup
Before using the projector, make sure you read the safety instructions in the
online
User’s Guide
.
Note:
These illustrations show the EX5210/EX7210, but the instructions are the
same for the EX3210 unless otherwise noted.
Connect the projector
Choose from the following connections. See the sections below or the online
User's Guide
for details.
Computer
USB Port
Connect the square end of a USB cable to the projector’s
USB
TypeB
(square) port. Connect the flat end of the cable to any USB port on your
computer.
Windows
®
2000 SP4 or later:
After turning on the projector, follow the
on-screen instructions to install the Epson USB Display software
(
EMP_UDSE.EXE
; only on first connection). If the software screen does not
display automatically, open
My Computer
or
Computer
, then double-click
EPSON_PJ_UD
.
Mac OS
®
X 10.5.1 or higher:
After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click
USB Display Installer
and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Note:
If you have problems installing the USB Display software, make sure the
USB Type B
setting in the projector’s
Extended
menu is set to
USB Display
.
See the online User’s Guide for instructions.
Monitor Port
Connect one end of a VGA cable to the projector’s
Computer
port, and the
other end to your computer’s
monitor port. If you are using a laptop,
switch it to external display (see “Troubleshooting”). You can also connect an
audio cable.
HDMI Port (EX5210/EX7210)
Connect one end of an HDMI cable to the projector’s
HDMI
port and the other
end to an HDMI port on your computer.
Video Device
Connect up to 4 (EX5210/EX7210) or 3 (EX3210) video devices and use
the remote control to switch between them. (HDMI is not available for
the EX3210.)
RCA video cable (composite video)
Component video to VGA cable
S-Video cable
Audio cable
HDMI cable
Camera, USB Device, or Epson Document Camera DC-06
Connect a digital camera, USB flash drive, USB storage device, or Epson
document camera DC-06 to the projector’s USB
TypeA
(flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature. See the
User’s Guide
for details.
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector.
The power light on the
projector turns orange.
3
Open the
A/V Mute
slide all the way.
4
Press the
power button on the
projector or remote control. The projector
beeps, the power light flashes green,
and then stays on.
Note:
To shut down the projector,
press the
power button twice, then
unplug it. You don’t have to wait for the
projector to cool down.
5
The default language of the menu system is
English
. To select another
language, press the
Menu
button on the remote control. Select
Extended
and press
Enter
. Select
Language
and press
Enter
. Select
your language and press
Enter
.
Press the
Menu
button to exit the
menu system.
Adjust the image
1
If you don’t see an image, press the
Source Search
button on the
projector or remote control to select the image source.
Note:
If you still see a blank screen or have other display problems, see the
troubleshooting tips on the right.
2
To raise the image, press the
foot release button and lift
the front of the projector.
Release the button to lock the
foot in position.
EX3210/EX5210/EX7210
USB cable
HDMI cable
VGA cable