Epson PP 100 User Guide

Epson PP 100 - Discproducer - DVD Duplicator x2 Manual

Get Epson PP 100 - Discproducer - DVD Duplicator x2 PDF manuals and user guides View all Epson PP 100 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson PP 100 manual content summary:

  • Epson PP 100 | User Guide - Page 1
    User's Guide 4113114-01
  • Epson PP 100 | User Guide - Page 2
    trademark and Exceed Your Vision is a trademark of Seiko Epson Corporation. Microsoft® and Windows® are registered trademarks, and Windows Vista™ is a trademark of Microsoft Corporation. Part of the photo data stored on the Software CD-ROM is licensed from Design Exchange Co., Ltd. Copyright
  • Epson PP 100 | User Guide - Page 3
    driver 14 Uninstalling EPSON Total Disc Maker 15 Chapter 2 Publishing Discs Introduction 17 Turning power on/off 17 Overview of publishing mode 18 Drive settings 19 Printer settings 19 Notice for CD/DVD writing and printing 20 Printing on CDs/DVDs with a commercially available software
  • Epson PP 100 | User Guide - Page 4
    labels 37 Publishing discs 38 Batch Mode 40 Loading CDs/DVDs 40 Making disc settings and creating labels 44 Publishing discs 44 Taking Out Discs 49 Canceling Publishing 50 Chapter 3 Replacing Ink Cartridges Checking the Ink Cartridge Status 51 Precautions on Ink Cartridge Replacement 52
  • Epson PP 100 | User Guide - Page 5
    is flashing or is on after you replace the cartridge 82 Software cannot be installed 82 Ink Pad Nearly Full message is displayed by the software 83 Appendix A Where To Get Help Contacting Customer Support 84 Before Contacting Epson 84 Help for Users in the United States and Canada 84 Help for
  • Epson PP 100 | User Guide - Page 6
    Discs 90 System Requirements 90 For using the product 90 Technical Specifications 91 Disc 91 Ink cartridges 93 Mechanical 94 Electrical 94 Environmental 95 Standards and approvals 95 Interface 95 Lifetime 96 Index Contents 6
  • Epson PP 100 | User Guide - Page 7
    Instructions Important Note You may use the software to operate the EPSON PP-100. You may use the EPSON PP-100 to copy materials onto disc, including but not limited to CDs and DVDs. You agree to respect the rights of copyright owners. EPSON photocopiers or air control systems that regularly switch
  • Epson PP 100 | User Guide - Page 8
    Do not attempt to service the product yourself. ❏ Unplug the product and refer servicing to qualified service personnel under the following turn it upside down. Otherwise, ink may leak from the cartridges. ❏ Leave enough space in front of the product for the disc cover to be fully opened. ❏
  • Epson PP 100 | User Guide - Page 9
    with soap and water. If ink gets into your eyes, flush them immediately with water. If discomfort or vision problems remain after a thorough flushing, see a doctor immediately. ❏ Do not remove or tear the label on the cartridge; this can cause leakage. Important Notice and Safety Instructions 9
  • Epson PP 100 | User Guide - Page 10
    port or the surrounding area. ❏ Do not store ink cartridges with the ink supply area facing down. This may result in ink leakage. Also, dirt attached to the ink supply area may result in the product not functioning properly. Notice for CD/DVD discs Before using the product, operation check should be
  • Epson PP 100 | User Guide - Page 11
    including bundled software, not be obtained, we cannot compensate for incidental loss arising from that fact, such as expenses required for use product's suitability after a full evaluation. ❏ When copying a CD or DVD, you must meet the conditions that the work recorded on the discs do not have a
  • Epson PP 100 | User Guide - Page 12
    expressly approved by Seiko Epson Corporation could void your authority to operate the equipment. FCC Compliance Statement For American Users This equipment has been , if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However,
  • Epson PP 100 | User Guide - Page 13
    will start. 2. Click Add. 3. Select the product to be added from CD/DVD Publisher List, then click Next. 4. Enter name and click OK. Adding the product is complete. Overview of EPSON Total Disc Maker The EPSON Total Disc Maker software included with the product allows you to write or 2007/02007/02
  • Epson PP 100 | User Guide - Page 14
    EPSON Total Disc Maker to do the following: New :For Ink Jet Printer ❏ Writing data to DVDs, data to CDs, music to CDs, music and data to CDs, or video to CDs, or copying CD/DVDs. ❏ Creating and editing CD/DVD labels. Starting EPSON Total Disc Maker Click Start, point to All Programs (Windows
  • Epson PP 100 | User Guide - Page 15
    "Accessing the printer driver" on page 14. In the printer driver window, try one of the following procedures. ❏ Right-click the item, then click Help. ❏ Click the button at the top right of the window, then click the item (for Windows XP and 2000 only). Uninstalling EPSON Total Disc Maker You can
  • Epson PP 100 | User Guide - Page 16
    Settings, and then select Control Panel. 2. Double-click the Add or Remove Programs icon. 3. Choose the software you want to uninstall from the list of programs. 4. Click Change/Remove. 5. When the confirmation message appears, click Yes. 6. Follow the on-screen instructions. Using Your Software 16
  • Epson PP 100 | User Guide - Page 17
    Chapter 2 Publishing Discs Introduction This section guides you through the procedures for creating and printing CDs/DVDs. Note: For information on CDs/DVDs, see the following section. & See "Discs" on page 90. Turning power on/off This section describes how to turn on/off power. Turning power
  • Epson PP 100 | User Guide - Page 18
    and connect it again. Overview of publishing mode To write data to CDs/DVDs and to print labels that you created/edited are called "Publish" New:Onlyformodelwiththisfeature in EPSON Total Disc Maker. The product has three kinds of publishing modes. Standard Mode This mode uses Stacker 1 as the input
  • Epson PP 100 | User Guide - Page 19
    You can create up to 100 CDs/DVDs at once without refilling and taking out discs while publishing. To use this mode, you need to place Stacker 3 into the product. Note: This mode does not use Stacker 4. & See "Batch Mode" on page 40. Drive settings Drive to be used Select Drive to Use from the
  • Epson PP 100 | User Guide - Page 20
    to Stacker 4 ❏ Batch Mode: Ejected to Stacker 2 or 3 Note: The error mark will not be printed in the following cases. ❏ The job was cancelled ❏ An incorrect disc type was found in the stacker ❏ Fatal error ❏ Not enough ink was left to print the error mark Notice for CD/DVD writing and printing
  • Epson PP 100 | User Guide - Page 21
    of the color saturation in the Color Settings dialog box of the printer driver. ❏ Moisture on the printable surface may cause smearing. ❏ When using Epson specified discs, High Speed can not be selected. ❏ Reprinting on the same CD/DVD may not improve the print quality. ❏ Be sure to clean the inside
  • Epson PP 100 | User Guide - Page 22
    supports CD/DVD printing, you have to make the following settings. Size Type Margins on all sides 124 x 124 mm (4.88 x 4.88") CD/DVD Label, CD/DVD Premium Label, or EPSON Specified CD/DVD Label 2 mm (0.08") Standard Mode Loading CDs/DVDs Follow the steps below to load CDs/DVDs. Publishing Discs
  • Epson PP 100 | User Guide - Page 23
    pause. Closing the disc cover automatically resume the job. ❏ Pause a job if you need to open the disc cover. 1. Open the disc cover. 2. Take out Stacker 1. 3. Fan a stack of discs to prevent them from sticking together. Be careful not to scratch the recording side of the disc. Publishing Discs 23
  • Epson PP 100 | User Guide - Page 24
    4. Load CDs/DVDs into Stacker 1 with the printable side facing up. c Caution: Do not load the discs above the red line marked on the stacker; otherwise, the discs or product may be damaged. 5. Insert Stacker 1. Publishing Discs 24
  • Epson PP 100 | User Guide - Page 25
    the labels printed on the discs. Accessing EPSON Total Disc Maker Click Start, point to All Programs (Windows XP) or Programs (Windows 2000), point to EPSON Total Disc Maker, and then click EPSON Total Disc Maker. To learn how to use EPSON Total Disc Maker, go to the Help menu. Publishing Discs 25
  • Epson PP 100 | User Guide - Page 26
    The following instructions explain how to publish CDs/DVDs. 2007/05/29 10:29:21070511 unlocked and changed Note: ❏ Be sure to let CDs and DVDs to dry completely before using them or touching the printed surface. Allow Epson specified discs to dry for at least 1 hour and other types of discs for at
  • Epson PP 100 | User Guide - Page 27
    3. Select Standard Mode for Publish Mode. Publishing Discs 27
  • Epson PP 100 | User Guide - Page 28
    4. Select the type of discs that you loaded into the stacker. 5. Click OK. Publishing Discs 1. Make the publish settings on the Publish screen of EPSON Total Disc Maker. For details, see Help for EPSON Total Disc Maker. Note: To access Help for EPSON Total Disc Maker, select Help from the Help menu.
  • Epson PP 100 | User Guide - Page 29
    button. c Caution: ❏ Do not open the disc cover while the product is publishing discs, unless the application instructs to add or remove discs. This may affect write quality or print quality. Also, do not put your hands inside the product while beeping as arm is still moving. ❏ If
  • Epson PP 100 | User Guide - Page 30
    External Output Mode Loading CDs/DVDs Follow the steps below to load CDs/DVDs. 1. Open the disc cover. 2. Take out Stacker 1. 3. Fan a stack of discs to prevent them from sticking together. Be careful not to scratch the recording side of the disc. Publishing Discs 30
  • Epson PP 100 | User Guide - Page 31
    4. Load CDs/DVDs into Stacker 1 with the printable side facing up. c Caution: Do not load the discs above the red line marked on the stacker; otherwise, the discs or product may be damaged. 5. Insert Stacker 1. Publishing Discs 31
  • Epson PP 100 | User Guide - Page 32
    them from sticking together. Be careful not to scratch the recording side of the disc. 8. Load CDs/DVDs into Stacker 2 with the printable side facing up. c Caution: Do not load the discs above the red line marked on the stacker; otherwise, the discs or product may be damaged. Publishing Discs 32
  • Epson PP 100 | User Guide - Page 33
    9. Insert Stacker 2. 10. Close the disc cover. c Caution: ❏ Do not yank Stacker 4 when pulling it out to remove published discs. ❏ Do not remove Stacker 4 when the Stacker 4 LED is flashing fast. Discs may be damaged. ❏ Unlock the lock lever when using Stacker 4. ❏ If you use Stacker 4 for output,
  • Epson PP 100 | User Guide - Page 34
    Making the stacker settings 1. Make sure the product is turned on, and the product and computer are properly connected. 2. Click the Properties icon on the Publish screen of EPSON Total Disc Setup. Publishing Discs 34
  • Epson PP 100 | User Guide - Page 35
    3. Select External Output Mode for Publish Mode. Publishing Discs 35
  • Epson PP 100 | User Guide - Page 36
    4. Select the type of discs that you loaded into Stacker 1. Publishing Discs 36
  • Epson PP 100 | User Guide - Page 37
    the labels printed on the discs. Accessing EPSON Total Disc Maker Click Start, point to All Programs (Windows XP) or Programs (Windows 2000), point to EPSON Total Disc Maker, and then click EPSON Total Disc Maker. To learn how to use EPSON Total Disc Maker, go to the Help menu. Publishing Discs 37
  • Epson PP 100 | User Guide - Page 38
    to publish CDs/DVDs. 2007/05/29 10:29:21070511 unlocked and changed Note: ❏ If the disc is ejected or not fed correctly when you start a CD/DVD print job, make sure you loaded the stacker properly. ❏ If you select CD/DVD Premium Label as the Label Type setting in the Printer Settings window and
  • Epson PP 100 | User Guide - Page 39
    button. c Caution: ❏ Do not open the disc cover while the product is publishing discs, unless the application instructs to add or remove discs. This may affect write quality or print quality. Also, for safety reason, do not put your hands inside the product while beeping as arm is
  • Epson PP 100 | User Guide - Page 40
    Batch Mode Loading CDs/DVDs Follow the steps below to load CDs/DVDs. 1. Open the disc cover. New :Only for model with this feature 2. Take out Stacker 1. 3. Fan a stack of discs to prevent them from sticking together. Be careful not to scratch the recording side of the disc. Publishing Discs 40
  • Epson PP 100 | User Guide - Page 41
    4. Load CDs/DVDs into Stacker 1 with the printable side facing up. c Caution: Do not load the discs above the red line marked on the stacker; otherwise, the discs or product may be damaged. 5. Insert Stacker 1. Publishing Discs 41
  • Epson PP 100 | User Guide - Page 42
    them from sticking together. Be careful not to scratch the recording side of the disc. 8. Load CDs/DVDs into Stacker 2 with the printable side facing up. c Caution: Do not load the discs above the red line marked on the stacker; otherwise, the discs or product may be damaged. Publishing Discs 42
  • Epson PP 100 | User Guide - Page 43
    9. Insert Stacker 2. 10. Insert Stacker 3. c Caution: ❏ Make sure that there are no discs in Stacker 4 when using Stacker 3. ❏ When using Stacker 3, do not pull out Stacker 4. Be sure to lock the lock lever located on Stacker 4 when you use Stacker 3. Publishing Discs 43
  • Epson PP 100 | User Guide - Page 44
    , point to All Programs (Windows XP) or Programs (Windows 2000), point to EPSON Total Disc Maker, and then click EPSON Total Disc Maker. To learn how to use EPSON Total Disc Maker, go to the Help menu. Publishing discs The following instructions explain how to publish CDs/DVDs. 2007/05/29 10:29
  • Epson PP 100 | User Guide - Page 45
    Making the stacker settings 1. Make sure that the product is turned on, and the product and computer are properly connected. 2. Click the Properties icon on the Publish screen of EPSON Total Disc Maker or EPSON Total Disc Setup. Publishing Discs 45
  • Epson PP 100 | User Guide - Page 46
    3. Select Batch Mode for Publish Mode. Publishing Discs 46
  • Epson PP 100 | User Guide - Page 47
    4. Select the type of discs that you loaded into the stacker. 5. Click OK. Publishing Discs 47
  • Epson PP 100 | User Guide - Page 48
    of EPSON Total Disc Maker. For details, see Help for EPSON Total Disc Maker. Note: To access Help for EPSON Total Disc Maker, select Help from the Help menu. 2. Click the Publish button. c Caution: ❏ Do not open the covers while the product is publishing discs, unless the application instructs to
  • Epson PP 100 | User Guide - Page 49
    differs according to the publishing mode. Refer the following table. Output stacker Stacker 2 Stacker 3 Stacker 4 Stacker 2 Mode Standard mode Batch mode Batch mode Standard mode External Output mode Number of discs Up to 50 discs Up to 50 discs Up to 5 discs Stacker 3 Stacker 4 3. Install the
  • Epson PP 100 | User Guide - Page 50
    If you need to cancel publishing, follow the instructions below. 2007/04/23 10:15:54070402 unlocked and changed When you start publishing, the screen of EPSON Total Disc Monitor appears on your computer screen. Select the job you want to cancel in the Unfinished Job list, and then select
  • Epson PP 100 | User Guide - Page 51
    the status is displayed on the EPSON Total Disc Monitor. To check the ink cartridge status, do the following: ❏ EPSON Total Disc Monitor appears automatically when you start a job. You can check the ink cartridge status from this window. You can also run EPSON Total Disc Monitor from the Start menu
  • Epson PP 100 | User Guide - Page 52
    with water. If discomfort or vision problems continue after a thorough flushing, see a doctor immediately. ❏ Epson recommends the use of genuine Epson ink cartridges. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may
  • Epson PP 100 | User Guide - Page 53
    the steps below. c Caution: Do not remove the cartridge from the product until you are ready to replace it with another. Note: The illustrations show replacement of the light magenta ink cartridge, but the instructions are the same for all the cartridges. 1. Make sure that the power light is on
  • Epson PP 100 | User Guide - Page 54
    out. (If the ink in the cartridge is low, it is indicated by a flashing ink cartridge light.) Note: If an ink cartridge is low, you may continue to use it until it is expended. To confirm the status of each ink cartridge, see the following section: & See "Using EPSON Total Disc Monitor" on page 73
  • Epson PP 100 | User Guide - Page 55
    is not installed promptly, the print head may dry out and be unable to print. ❏ Do not refill the ink cartridge. Other products not manufactured by Epson may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic product behavior. 6. Place the new
  • Epson PP 100 | User Guide - Page 56
    7. When you are finished replacing cartridges, close the ink cartridge cover. Replacing Ink Cartridges 56
  • Epson PP 100 | User Guide - Page 57
    identify the problem by errors, and that the disc cover is closed. 3. Access the printer driver. See "Accessing the printer driver" on page 14. 4. Click the Utility tab, then click the Nozzle Check button. 5. Follow the on-screen instructions. Below are two sample nozzle check patterns. Compare
  • Epson PP 100 | User Guide - Page 58
    -endINJLewFP:,Duespeempoadretsl. to solve these problems by cleaning the print head, which ensures that the nozzles are delivering ink properly. You can clean the print head from your computer using the Head Cleaning utility in the printer driver or from the product by using the buttons
  • Epson PP 100 | User Guide - Page 59
    Make sure that no lights are indicating errors, and that the disc cover is closed. 3. Access the printer driver. See "Accessing the printer driver" on page 14. 4. Click the Utility tab, then click the Head Cleaning button. 5. Follow the on-screen instructions. The power light flashes while the
  • Epson PP 100 | User Guide - Page 60
    errors, and that the disc cover problem after replacing the ink cartridges, contact your dealer. Aligning the Print Head If you notice a misalignment of vertical lines or horizontal banding, you may be able to solve this problem by using the Print Head Alignment utility in your printer driver
  • Epson PP 100 | User Guide - Page 61
    sure that no lights are indicating errors, and that the disc cover is closed. 3. Access the printer driver. See "Accessing the printer driver" on page 14. 4. Click the Utility tab, then click the Correcting the Printing Position button. 5. Follow the on-screen instructions to adjust the vertical and
  • Epson PP 100 | User Guide - Page 62
    dry with a dry, soft cloth. Note: ❏ After cleaning the product, close the disc cover and the Stacker 4 tray to protect the product from dust. ❏ Make sure , and then unplug the power cord from the electrical outlet. 2. Open the disc cover, and remove the stackers from the product. 3. Use a soft, clean
  • Epson PP 100 | User Guide - Page 63
    components. ❏ Do not spray the inside of the product with lubricants. ❏ Unsuitable oils can damage the mechanism. Contact your dealer or a qualified service person if lubrication is needed. ❏ Dirt attached to Stacker 3 or 4 should be wiped clean with a soft cloth moistened with neutral detergent
  • Epson PP 100 | User Guide - Page 64
    and unplug its power cord. 2. Disconnect the interface cable. 3. Remove all discs from the stackers. 4. Open the ink cartridge cover. Secure the ink cartridges with tape, then close the ink cartridge cover. 5. Close the disc cover and Stacker 4 tray. Secure them with tape. Maintaining Your Product
  • Epson PP 100 | User Guide - Page 65
    6. Attach the protective materials to both sides of the product. 7. Repack the product and accessories in the original box. Note: ❏ Keep the product level during transport. ❏ Be sure to remove the protective materials and tape from the product before using it again. ❏ Be sure to lift the product by
  • Epson PP 100 | User Guide - Page 66
    by Help, the control panel, and the EPSON Total Disc Monitor utility. Refer to the appropriate section below. If you have a specific problem relating to publishing quality, a problem not related to publishing quality, or a disc feeding problem, or if the product does not publish at all, refer to the
  • Epson PP 100 | User Guide - Page 67
    cover open Close covers. Job is paused since disc cover or ink cartridge cover was opened while processing the job Wait for the job to resume. Error associated with disc transfer Power Busy Lights Error Ink Conditions/Remedies Stacker 1234 Disc pick up error Turn off the product and remove the
  • Epson PP 100 | User Guide - Page 68
    product again and let initializing process remove the disc. ❏ If resuming label printing after the error, run Nozzle Check and confirm the condition of the print head. ❏ If the publishing does not start, check if a print job remains in the print spooler and delete all print jobs. Troubleshooting 68
  • Epson PP 100 | User Guide - Page 69
    Remove discs so that discs are below the red line. Stacker 2 is overloaded Remove discs so that discs are below the red line. Stacker 3 if full Remove published discs from Stacker 3. Stacker 4 if full Remove published discs from Stacker 4. Stacker 4 is open Close Stacker 4. Troubleshooting 69
  • Epson PP 100 | User Guide - Page 70
    on page 51. Incorrectly installed ink cartridge Reinsert the ink cartridge. See "The ink light is flashing or is on after you replace the cartridge" on page 82. Ink cartridge not fully inserted All ink lights are on. Check ink cartridges and make sure they are all fully inserted. Troubleshooting 70
  • Epson PP 100 | User Guide - Page 71
    by the software. There will be no lights indicating it. Please have an authorized Epson service center service the ink pad right away. The pad is nearly full and the unit will stop functioning when the pad becomes full. Do not attempt to service the unit yourself. Product maintenance error A product
  • Epson PP 100 | User Guide - Page 72
    resume job. If there is a problem with the drive, change the drive with EPSON Total Disc Setup and resume the job. If the same error occurs frequently, contact your dealer. Invalid disc error An invalid disc error has occurred, such as the disc may not be blank or the disc does not have enough space
  • Epson PP 100 | User Guide - Page 73
    , contact your dealer. EPSON Total Disc Monitor If a problem occurs while printing, an error message will appear in the EPSON Total Disc Monitor window. If an error message appears indicating the parts inside the product are near the end of their service life or the waste ink pad in the product is
  • Epson PP 100 | User Guide - Page 74
    tips for better publishing. ❏ Ink Cartridge Status: This provides a graphic display of the ink cartridge status. ❏ Drive, Printer, Stacker Status: This provides a graphic display of the drives, printer, and stacker status. It also shows where an error occurs. Print Quality Problems If you are
  • Epson PP 100 | User Guide - Page 75
    " on page 77 Horizontal banding ❏ Make sure the printable side of the disc is face up in the Stacker. ❏ Run the Head Cleaning utility to clear any clogged ink nozzles. & See "Cleaning the Print Head" on page 58. ❏ Use ink cartridges within six months after opening the packages. Troubleshooting 75
  • Epson PP 100 | User Guide - Page 76
    Epson ink cartridges. ❏ Check the H ink light. If the light is flashing, replace the appropriate ink cartridge. & See "Replacing an Ink Cartridge" on page 53. ❏ Make sure the label type selected in the printer driver is appropriate for the type of disc loaded in the product. & See "Publishing Discs
  • Epson PP 100 | User Guide - Page 77
    Spooler (Windows XP and 2000).2007/03/2309:39:18070313Unlockedandchanged ❏ Turn off the product and computer. Make sure the product's interface cable is securely plugged in. ❏ Uninstall the printer driver, then reinstall it. & See "Uninstalling EPSON Total Disc Maker" on page 15. Troubleshooting 77
  • Epson PP 100 | User Guide - Page 78
    on page 15. Printing is too slow ❏ Make sure the label type selected in the printer driver is appropriate for the type of disc loaded in the product. & See "Publishing Discs" on page 17. ❏ Close any unnecessary applications. ❏ Make sure that printing mode is set to bi-directional. Troubleshooting 78
  • Epson PP 100 | User Guide - Page 79
    driver, then reinstall it. & See "Uninstalling EPSON Total Disc Maker" on page 15. Ink adheres to the recording surface ❏ Depending on the type of disc, ink may adhere to the recording surfaces if they are stacked right after printing. Make sure of the type of disc before using. Disc or the CD/DVD
  • Epson PP 100 | User Guide - Page 80
    occurs, turn off/on the power and try resolving the problem by initializing the product. If the error continues to occur, contact customer support. If your discs jam frequently, make sure of the following: ❏ The discs are smooth, not damaged. ❏ You are using a high-quality discs. Troubleshooting 80
  • Epson PP 100 | User Guide - Page 81
    Problem Cannot write to the disc Avoid using the product where dust or smoke is abundant. It may result in write error. If a disc write error occurs frequently, check the following: ❏ The disc is not damaged. ❏ The disc outlet works and is not controlled by a wall switch or timer. Troubleshooting 81
  • Epson PP 100 | User Guide - Page 82
    memory in your computer. ❏ Uninstall the printer driver, then reinstall it. & See "Uninstalling EPSON Total Disc Maker" on page 15. The ink light is flashing or is on after you replace the cartridge Make sure the ink cartridge is correctly installed. Software cannot be installed ❏ Is the USB cable
  • Epson PP 100 | User Guide - Page 83
    Nearly Full message is displayed by the software Ink pad is nearly full. Please have an authorized Epson service center replace the ink pad right away. The pad is nearly full, and the unit will stop functioning when the pad becomes full. Do not attempt to service the unit yourself. Troubleshooting
  • Epson PP 100 | User Guide - Page 84
    computer operating system name and version ❏ Names and versions of the software applications you normally use with your product Help for Users in the United States and Canada Contacts for information, support, and services are: Discproducer Technical Support: 562-276-1360 Location: Epson America Inc
  • Epson PP 100 | User Guide - Page 85
    and FAQs. Help for Users in the Europe (EMEA) Contacts for information, support, and services are: Web site URL: http://www.discproducer.epson-europe.com If you need the latest drivers, FAQs, manuals, or other downloadable, access the site at: http://download.epson-discproducer.com Or contact your
  • Epson PP 100 | User Guide - Page 86
    cover: Secures the ink cartridges. Open only when installing or replacing ink cartridges. b. Control Panel: Use the button and monitor the lights to control your product. See the next section for details. c. Disc cover: Open when loading or taking out the discs. d. Power button: Turns the product
  • Epson PP 100 | User Guide - Page 87
    Leave at least 10 cm (3.94") between the back of the product and the wall for ventilation. i. Disc remover cover: Open this cover only when a disc is stuck in the printer tray. c Caution: Before opening the disc remover cover, be sure to unplug the power cable from the wall outlet. Be sure to attach
  • Epson PP 100 | User Guide - Page 88
    Lock the lever when you use Stacker 3 in Batch mode. o. Stacker 3: Use Stacker 3 as a disc output stacker. Holds up to 50 discs. p. Stacker 4: Use Stacker 4 as a disc output stacker. Holds up to 5 discs. q. Printer: Prints on label surface of discs. r. Drive 2: Writes data on the recording surface
  • Epson PP 100 | User Guide - Page 89
    C13S020450 C13S020451 C13S020452 To purchase a PP-100 Series exclusive ink cartridge, check with the dealer where you purchased your PP-100 or access either of the following urls: http://www.discproducer.epson-europe.com (Europe) http://www.discproducer.epson.com (United States and Canada
  • Epson PP 100 | User Guide - Page 90
    Discs Epson offers the specified CD-R and DVD-R discs for all your printing needs. on mNodeewl (:SDeeepSepnedcs) System Requirements For using the product Windows requirements New :Depends on model (See Spec) To use this product, you must have any of the following Windows operating systems
  • Epson PP 100 | User Guide - Page 91
    mm + 0.3/- 0.1 mm (0.047 +0.012"/-0.004") Printable *Glossy labels other than the specified disc are not supported. CD-R, DVD-R Notes for handling the disc ❏ The specified discs hava a moisture-adhesive ink receptor layer on the label surface. If stored stacked, especially under high humidity and
  • Epson PP 100 | User Guide - Page 92
    from Set Inner/Outer Diameter screen of the EPSON Total Disc Maker. In the Set Inner/Outer Diameter screen, you can select Standard, Wide, or set manually. Following diagram shows the printable area for Standard and Wide. Printing will be done in the gray area. CD/DVD: New :Depends on model 12-cm
  • Epson PP 100 | User Guide - Page 93
    from another application, set from the user-defined label setting in the printer driver. If you print from the Total Disc Maker, set from Set Inner/Outer Diameter setting. Note: When you print on CDs/DVDs with a commercially available software package that supports CD/DVD printing, you have to make
  • Epson PP 100 | User Guide - Page 94
    ships with full cartridges and part of the ink from the first cartridges is used for priming its printer. See www.discproducer.epson.com for more information about cartridges. Mechanical Drive Stacker capacity Dimensions Weight Two drives, tray loading type Stacker 1 to 3: Max. 50 discs Stacker
  • Epson PP 100 | User Guide - Page 95
    Power consumption Printing Standby mode 41 W 24 W Note: Check the label on the back of the product for its voltage. Environmental Temperature Humidity *1 Without condensation Operation: 10 to 35 °C (50
  • Epson PP 100 | User Guide - Page 96
    burned The product's ink pad is expected to become saturated and need replacing after printing about 30,000 discs. The burner life estimate is the combined life for the two burners, with the low estimate based on burning DVDs only, and the high estimate based on burning CDs only. Expected lifetimes
  • Epson PP 100 | User Guide - Page 97
    , 87 Canceling printing, 50 CD/DVD printable area, 92 printing, 22, 30, 40 publishing, 26, 38, 44 Cleaning print head, 58 product, 61 Color problems, 76 Contacting Epson, 84 Control panel, 86, 88 Correcting the printing position, 61 D Disc cover, 86 Driver accessing for Windows, 14 uninstalling, 15
  • Epson PP 100 | User Guide - Page 98
    84 Smeared prints, 77, 78 Software uninstalling, 15 Specifications ink cartridges, 89 mechanical, 94 paper, 91 Speed, increasing, 78 Stacker, 88 Status Monitor Windows, 73 System requirements, 90 T Transporting product, 64 U USB connector, 87 W Windows accessing printer settings, 14 status monitor
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
User’s Guide
4113114-01