Epson PowerLite Pro Cinema LS9600e Start Here
Epson PowerLite Pro Cinema LS9600e Manual
 |
View all Epson PowerLite Pro Cinema LS9600e manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson PowerLite Pro Cinema LS9600e manual content summary:
- Epson PowerLite Pro Cinema LS9600e | Start Here - Page 1
PowerLite® Pro Cinema LS9600e Quick Setup Before using the projector, make sure you read the safety instructions in the online User's Guide. WirelessHD Transmitter Follow these steps to set up the included WirelessHD Transmitter. Choose a location Keep the projector may be supported. Check your - Epson PowerLite Pro Cinema LS9600e | Start Here - Page 2
display Switch between 2D and 3D Navigate projector menus Control WirelessHD functions For more information on using the remote control, see the online User's Guide. 5 Press the Lens button on the remote control again and use the , , and buttons to reposition the image. 6 If your image - Epson PowerLite Pro Cinema LS9600e | Start Here - Page 3
the WirelessHD button on the projector remote control. Note: If the WirelessHD connection fails, see the "Troubleshooting" section. 6 If See "Choose a location" on the front of this sheet or the online User's Guide for more information. • Check that your 3D glasses have not entered standby mode. - Epson PowerLite Pro Cinema LS9600e | Start Here - Page 4
desktop to access the online manual (requires an Internet connection). If you don't have a User's Guide icon, you can install it from the projector CD or go to the Epson website, as described below. Telephone support services To use the Epson® PrivateLine® Support service, call (800) 637-7661. This
-
1 -
2 -
3 -
4
 |
 |
Quick Setup
Before using the projector, make sure you read the safety instructions in the
online
User’s Guide
.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use
the lens shift feature or the keystone correction button on the projector to
reposition the image (see “Adjust the image”).
In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
See the online
User’s Guide
for more information on where to place your
projector.
Connect the projector
Choose from the following connections. For additional connection types, see
the online
User’s Guide.
Video device
1
Loosen the two screws at the bottom of the cable cover, then pull the
cover forward.
2
Lift the cable cover out of the grooves at the top.
3
Connect up to 4 video devices and use the Source
buttons on the remote
control or the
button on the projector to switch between them.
Component video cable
RCA video cable
HDMI cable
WirelessHD Transmitter
Follow these steps to set up the included WirelessHD Transmitter.
HDMI
1
Place the transmitter within 32 feet (10 m) of the projector. Make sure the
front of the transmitter faces the front of the projector. See the online
User’s Guide
for more information on the WirelessHD transmission range.
Note:
Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
2
Plug the AC adapter into the transmitter and a wall outlet.
3
Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the WirelessHD Transmitter. You can connect up
to five input devices to the transmitter. See “Viewing WirelessHD content”
for information on switching between input sources
Note:
You can connect tablets, smartphones and other devices that
support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Devices that use an MHL connection include
the Samsung™ Galaxy Note™ II and the Roku
®
Streaming Stick™. Some
devices may require an adapter or may not require an MHL cable.
Not all features or functions may be supported. Check your device’s
documentation for more information.
4
To use the transmitter as a pass-through device to a television or other
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” for
information on switching between wireless and wired display modes.
PowerLite
®
Pro Cinema LS9600e
*412630400*
*412630400*