Epson Stylus NX200 Start Here

Epson Stylus NX200 - All-in-One Printer Manual

Get Epson Stylus NX200 - All-in-One Printer PDF manuals and user guides View all Epson Stylus NX200 manuals
Add to My Manuals
Save this manual to your list of manuals

Epson Stylus NX200 manual content summary:

  • Epson Stylus NX200 | Start Here - Page 1
    Start Here Epson Stylus® NX200 Series 1 Unpack (Included for Canada only) If anything is missing, contact Epson as described on the back. Caution: Do not open the ink cartridge package until you are ready to install the ink. Cartridges are vacuum packed to maintain reliability. Canada only: For
  • Epson Stylus NX200 | Start Here - Page 2
    3 Install cartridges Note: Do not load paper yet. 1 Lift up the scanner, then open the cartridge cover. 2 Shake the ink cartridges, then unpack them. 3 Remove only the yellow tape from each cartridge. Caution: Do not remove any other seals or the cartridge may leak. 4 Insert the cartridges in the
  • Epson Stylus NX200 | Start Here - Page 3
    6 Close the cartridge cover. Press down until it clicks. 7 Lower the scanner. 8 P ress the Stop button to charge the ink. Charging takes about 21/2 minutes. Caution: Don't turn off the NX200 Series while it is charging or you'll waste ink. 4 Load paper 1 Open the paper support and pull up the
  • Epson Stylus NX200 | Start Here - Page 4
    3 Flip the feeder guide forward. Then squeeze the edge guide and slide it left. 4 Load paper against the right edge and underneath the tab, with the printable side face up. 8½ 11 4 6 Note: Don't load the paper sideways; always load it short edge first. 5 Slide the edge guide over.
  • Epson Stylus NX200 | Start Here - Page 5
    Mac OS® X 10.3.9, 10.4.x, and 10.5.x. Windows 1 M ake sure the NX200 Series is NOT CONNECTED to your computer. Note: If you see a Found New Hardware screen, click Cancel and disconnect the USB cable. You can't install your software that way. 2 Insert the Epson Stylus NX200 Series CD. With Windows
  • Epson Stylus NX200 | Start Here - Page 6
    2 Insert the Epson Stylus NX200 Series CD. 3 Double-click the Epson icon. 4 Click Install and follow the on-screen instructions. 5 When prompted, connect the USB cable. Use any open USB port on your Macintosh. Make sure the NX200 Series is securely connected and turned on. 6 Mac OS X 10.5 users
  • Epson Stylus NX200 | Start Here - Page 7
    the NX200 Series User's Guide, FAQs, online troubleshooting advice, and software downloads. You can also purchase paper and ink. On-screen help with your software Select Help or ? when you're using your software. Epson Technical Support Internet Support Visit Epson's support website at epson.com
  • Epson Stylus NX200 | Start Here - Page 8
    all rights in those marks. This information is subject to change without notice. © Epson America, Inc. 2009, 3/09 CPD-25335R1 Cut out the card to the right and keep it with you when purchasing replacement ink cartridges. Epson NX200 Series Ink Cartridges 69 or 88 Black 69 or 88 Cyan 69 88 or
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Epson Stylus
®
NX200 Series
Start Here
1
Turn on the NX200 Series
1
Connect the power cable.
Note:
Do not connect to the computer at this time.
2
Press the
On
button.
Unpack
If anything is missing, contact Epson as described on the back.
Caution:
Do not open the ink cartridge package until you are ready to install
the ink. Cartridges are vacuum packed to maintain reliability.
Canada only:
For French speakers, remove the control panel sticker(s)
from the backing sheet and place over the corresponding text on the
control panel.
2
(Included for Canada only)