Epson Stylus Pro 10600 - Photographic Dye Ink Quick Reference Guide
Epson Stylus Pro 10600 - Photographic Dye Ink - Stylus Pro 10600 Print Engine Manual
View all Epson Stylus Pro 10600 - Photographic Dye Ink manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson Stylus Pro 10600 - Photographic Dye Ink manual content summary:
- Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 1
sure it's set up as described in Chapter 1 of the Printer Guide. Setting Up the Paper and Spindle 1 Open the roll paper cover and lift out the spindle. 4 Slide the movable paper stop back onto the spindle - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 2
lever out, to the released position. 5 Push the paper set lever all the way in, then close the roll paper cover. To avoid damaging the printer, never move the paper set lever while the Operate or Pause light is flashing. If you're using Roll Auto Cut and the leading edge - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 3
the board with the scale on the roll paper cover. To avoid damaging the printer, never move the paper set lever while the Operate or Pause light is display. 7 Run your print job. After printing, the posterboard stays in the printer. 8 Hold the posterboard as you pull the paper set lever out. Then - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 4
below, you need to run a cleaning cycle. 5 Make sure that all of the Ink Out lights on the printer's control panel are off. If an Ink Out light is flashing or on, you need to replace the corresponding ink cartridge instead. 6 Press the Cleaning button and hold it for at least 3 seconds. The Pause - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 5
print head. Before you begin, print a nozzle check (see page 4) to ensure that the problem is not caused by clogged nozzles. 1 Make sure the printer is turned on and 44-inch wide paper is loaded. (Be sure to use coated ink jet paper, such as the Doubleweight Matte Paper that came with the - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 6
empty. Make sure you have the correct replacement cartridge. 2 Locate the slot containing the empty ink cartridge corresponding to the Ink Out light. Press down on the top of the clamp and pull it forward. EPSON Photographic Dye™ ink • Black T499201 • Light cyan • Cyan T502201 • Light magenta - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 7
package. If you're using Archival or UltraChrome ink, shake the cartridge gently before installing it. 7 Close the ink compartment cover. 5 Hold the cartridge so the arrow mark is on the left side and points to the rear of the printer. Then insert the cartridge into the slot. Don't force it. 7 - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 8
Printer Guide. Message INK LOW INK OUT LOAD ROLL PAPER LOAD SHEET PAPER Light Ink Out light(s) flashing Ink Out light(s) on Paper Out light on Explanation Response Ink cartridge(s) nearly Replace ink cartridge Note the error number and contact needs to be replaced soon. EPSON. Continue 8 - Epson Stylus Pro 10600 - Photographic Dye Ink | Quick Reference Guide - Page 9
and troubleshooting, and get technical advice through e-mail. Contact the RIP manufacturer. EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON UltraChrome, EPSON Archival, and EPSON Photographic Dye are trademarks and EPSON Preferred is a service mark of Epson
Loading Roll Paper
Loading Roll Paper
Before using the printer, make sure it’s set up as described
in Chapter 1 of the
Printer Guide
.
Setting Up the Paper and Spindle
1
Open the roll paper cover and lift out the spindle.
2
Slide the movable paper stop off the left end of the
spindle.
4
Slide the movable paper stop back onto the spindle
and insert it firmly into the end of the roll.
5
Insert the white
end of the spindle (with the fixed
paper stop) into the right mounting bracket.
1
Continue
paper stop
6
Place the black end of the spindle into the left
mounting bracket.
3
Position the roll so the paper unwinds as
shown, then slide the roll onto the spindle so it
fits securely against the paper stop.
Handle the roll carefully and avoid
touching the printable side of the paper
with bare hands. Fingerprints may affect
print quality.
SP10600 QRG
9/16/02, 05:11 PM
1