Epson Stylus Pro 7900 Computer To Plate System User's Guide - Large Plate Acce
Epson Stylus Pro 7900 Computer To Plate System - Stylus Pro 7900 Computer Manual
 |
View all Epson Stylus Pro 7900 Computer To Plate System manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson Stylus Pro 7900 Computer To Plate System manual content summary:
- Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 1
Epson Stylus® Pro 7900CTP Large Plate Accessory Kit User's Guide - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 2
2 | Introduction Introduction The Large Plate Accessory Kit enables the Epson Stylus® Pro 7900CTP Computer to Plate System to print and cure large aluminum plates. The kit contains a large plate guide for the printer and a tray extension for the plate curing unit (PCU). The Large Plate Accessory Kit - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 3
on the printer. 1. Open the roll paper cover on the printer. 2. Remove the roll paper if installed (see the Epson Stylus Pro 7900/9900 Printer Guide for information). 3. Remove the small plate guide if installed. 4. Locate the first and last slots in the back row of slots. Location of first slot - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 4
with the Epson Stylus Pro 7900CTP system. If you don't have the CD, you can download it from www.proimaging.epson.com. If you are using the RIP included with the Epson Stylus Pro 7900CTP system, you can print the file using the menu options. Note: You must use an Epson DirectPlate Aluminum plate for - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 5
Aligning the Large Plate Guide | 5 3. Use a metric ruler to measure the distance from the left edge of the plate to point A on the printed plate. Then measure the distance from the left edge of the plate to point B. If the distances to points A and B are equal, go to step 6. If they vary by more - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 6
step 4 until the measurements are nearly equal, within 0.5 mm. 6. Once the plate guide is aligned, you need to confirm the alignment. Use a new plate to print the test pattern, then print the test pattern again on the same plate. The plate is correctly aligned when the line thickness at the top and - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 7
in the Printer Caution: Use only Epson DirectPlate Aluminum plates. Examine each plate carefully before you use it. If the plate is dented or the corners or edges are bent, do not use it. Even the slightest bent corner can damage the printer. WARNING: The plate edges are sharp. Use caution to avoid - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 8
slot (short edge first) so at least 1 to 2 inches of the top edge are above the large plate guide. For example, the top edge of a 19-inch long plate should be no less than 2 to 3 inches above the plate guide. Slide the plate against the two alignment points along the top and bottom of the large - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 9
OK? on the LCD screen, be sure to select NO PAPER SELECTED. Note: If you will use multiple plates consecutively on the printing press, it is best to load plates into the printer in the same direction each time. Otherwise, there is a possibility of minor differences in final printing. Unloading - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 10
attaches to the larger tray supplied with the PCU; the tray should be used as the input tray. Note: The extension adds a small incline for the plate to travel into the oven. 1. Attach the extension supports to both sides of the tray extension. Secure the screws with included hexagonal wrench - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 11
Stylus Pro 7900CTP Computer to Plate System User's Guide. Note: You can remove the large plate guide to print paper and then reinsert the large plate guide without having to realign it, assuming the large plate guide is put back in place correctly. Where to Get Help Epson provides technical support - Epson Stylus Pro 7900 Computer To Plate System | User's Guide - Large Plate Acce - Page 12
instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. Trademarks Epson and Epson Stylus
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
Epson Stylus
®
Pro 7900CTP Large Plate Accessory Kit
User’s Guide