Epson WorkForce 630 User Manual - Page 30

Insert the new ink cartridge into the holder, the ink cartridge. - ink refill

Get Epson WorkForce 630 PDF manuals and user guides View all Epson WorkForce 630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

4. Squeeze the tab on the cartridge and lift it up. Dispose of it carefully. Do not take the used cartridge apart or try to refill it. Warning: If ink gets on your hands, wash them thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. Keep ink cartridges out of the reach of children and don't drink the ink. 5. Before you open the new cartridge package, shake it gently four or five times. Then remove it from the package. 6. Remove the yellow tape from the bottom of the ink cartridge. Caution: Do not remove any other labels or seals, or ink will leak. Do not touch the green chip on the front of the cartridge. This can damage the ink cartridge. 7. Insert the new ink cartridge into the holder and push it down until it clicks into place. 8. Once you replace all the cartridges that need replacing, close the cartridge cover and push it down until it clicks into place. 9. Close the scanner to begin charging the ink. This takes about 2 1/2 minutes. When you see a completion message on the LCD screen, ink charging is finished. Caution: Never turn off the product while ink is charging or you'll waste ink. If you see an ink replacement message on the LCD screen, press OK and press down all the cartridges securely. Then press OK again. If you remove a low or expended ink cartridge, you cannot reinstall and use the cartridge. 30 Replacing Ink Cartridges

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
30
Replacing Ink Cartridges
4.
Squeeze the tab on the cartridge and lift it up.
Dispose of it carefully. Do not take the used
cartridge apart or try to refill it.
Warning:
If ink gets on your hands, wash them thoroughly with
soap and water. If ink gets into your eyes, flush them
immediately with water. Keep ink cartridges out of the
reach of children and don’t drink the ink.
5.
Before you open the new cartridge package,
shake it gently four or five times. Then remove
it from the package.
6.
Remove the yellow tape from the bottom of
the ink cartridge.
Caution:
Do not remove any other labels or seals, or ink will
leak. Do not touch the green chip on the front of
the cartridge. This can damage the ink cartridge.
7.
Insert the new ink cartridge into the holder
and push it down until it clicks into place.
8.
Once you replace all the cartridges that need
replacing, close the cartridge cover and push it down until it clicks into place.
9.
Close the scanner to begin charging the ink. This takes about 2 1/2 minutes.
When you see a completion message on the LCD screen, ink charging is
finished.
Caution:
Never turn off the product while ink is charging or you’ll waste ink. If you see an ink
replacement message on the LCD screen, press
OK
and press down all the cartridges
securely. Then press
OK
again. If you remove a low or expended ink cartridge, you
cannot reinstall and use the cartridge.