Fluke 1625 FE 1625 Users Manual - Page 69

Replacing Batteries, For replacement of batteries the measuring cable must - replacement parts

Get Fluke 1625 PDF manuals and user guides View all Fluke 1625 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Earth/Ground Tester Care and Maintenance detergent or spirit. Avoid aggressive cleaning agents and solvents (trilene, chlorothene etc.). Service work must only be undertaken by trained qualified staff. In all repair work care must be taken that the design parameters of the instrument are not modified to the detriment of safety, that assembled parts correspond to the original spares and that they are reassembled properly (factory state). Caution Before any maintenance, repair or parts replacement the instrument must be disconnected from all voltage sources. Replacing Batteries Note NiMH or NiCADcells may be used but must be charged outside of the instrument. The number of measurements available with these cells will typically be different to those available using alkaline cells. This instrument is equipped with six 1.5 V batteries IEC RL 6 or type AA. If after pressing the START-button all display-segments are lit (instrument resets, display-test) or if "LO-BAT" appears on display during a measurement the batteries must be replaced or the accumulators must be recharged. Caution For replacement of batteries the measuring cable must be disconnected, and the instrument switched off. Now the two screws at the rear of the instrument can be loosened with a suitable tool (screwdriver) and the battery recess cover removed. When replacing batteries, mind the correct polarity. Always replace the complete set of batteries. Note For protection of the environment, please ensure proper disposal of the batteries. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Earth/Ground Tester
Care and Maintenance
61
detergent or spirit. Avoid aggressive cleaning agents and solvents (trilene,
chlorothene etc.).
Service work must only be undertaken by trained qualified staff.
In all repair work care must be taken that the design parameters of the instru-
ment are not modified to the detriment of safety, that assembled parts corre-
spond to the original spares and that they are reassembled properly (factory
state).
Caution
Before any maintenance, repair or parts replacement the
instrument must be disconnected from all voltage sources.
Replacing Batteries
Note
NiMH or NiCADcells may be used but must be charged outside of the
instrument. The number of measurements available with these cells
will typically be different to those available using alkaline cells.
This instrument is equipped with six 1.5 V batteries IEC RL 6 or type AA. If
after pressing the START-button all display-segments are lit (instrument re-
sets, display-test) or if “LO-BAT” appears on display during a measurement
the batteries must be replaced or the accumulators must be recharged.
Caution
For replacement of batteries the measuring cable must be
disconnected, and the instrument switched off. Now the
two screws at the rear of the instrument can be loosened
with a suitable tool (screwdriver) and the battery recess
cover removed. When replacing batteries, mind the correct
polarity.
Always replace the complete set of batteries.
Note
For protection of the environment, please ensure proper disposal of
the batteries.