Fluke 1736/B Manual
Fluke 1736/B Manual
 |
View all Fluke 1736/B manuals
Add to My Manuals
Save this manual to your list of manuals |
Fluke 1736/B manual content summary:
- Fluke 1736/B | Manual - Page 1
Adapter for 17xx Power and Energy Loggers Instructions Introduction The Auxiliary Input Adapter (or other applications such as solar energy systems. PN 4749275 December 2015 ©2015 Fluke Corporation. All rights reserved. Specifications are subject to change without notification. MyFlukeStore - Fluke 1736/B | Manual - Page 2
XW Warnings To prevent possible electrical shock, fire, or personal injury: • Read all safety information before you use the Product. • Carefully read all instructions. • Use the Product only as specified, or the protection supplied by the Product can be compromised. • Do not touch voltages >30 V ac - Fluke 1736/B | Manual - Page 3
• Comply with local and national safety codes. Use personal protective equipment (approved rubber gloves, face protection, and flame-resistant clothes) to prevent shock and arc blast injury where hazardous live conductors are exposed. • Do not use the Product around explosive gas, vapor, or in damp - Fluke 1736/B | Manual - Page 4
Symbol Symbols Description W WARNING. RISK OF DANGER. X WARNING. HAZARDOUS VOLTAGE. Risk of electric shock. Consult user documentation. T Double Insulated Earth Measurement Category II is applicable to test and measuring circuits connected directly to utilization points (socket - Fluke 1736/B | Manual - Page 5
Direct Input 0 V DC to 10 V DC Configuration To connect the Adapter: 1. Make sure that all 4 mm safety test leads are disconnected. 2. Loosen the 4 captive screws and remove the lid to open the housing. 1 2 5 4 3 Ø 3-6 mm 0,12-0,24in 40mm 1,57in 10mm 0,39in 3. Cut and strip the cable. 4. - Fluke 1736/B | Manual - Page 6
5. Insert the sensor cable through the strain relief . The cable diameter must be in the range of 3 mm to 6 mm to ensure proper strain relief. 6. Tighten the strain relief. 7. To connect the wires to the terminals E, press the opening lever. 8. Correctly orient the lid and close the housing. 9. - Fluke 1736/B | Manual - Page 7
How to Clean Clean the Product with a soft cloth, mild soap, and water. W Caution To avoid damage, do not clean with abrasives or solvents. Specifications General Calibration Cycle 2 years Warranty 1 year Dimensions 119 mm x 86 mm x 38 mm (4.69 in x 3.39 in x 1.5 in) Weight 280 g (0.6 lb) Output - Fluke 1736/B | Manual - Page 8
Accuracy Input Range Intrinsic Accuracy Aux Adapter + Instrument (% of Reading + % of Range) Direct Input ±10 V see instrument specification Voltage divider input ±1000 V ±(0.5% + 0.002%) Note: Environmental Reference Conditions: 23 °C ±5 °C, instrument operating for at least 30 minutes, no - Fluke 1736/B | Manual - Page 9
Block Diagram VVooltaltaggeeDDiviivdideer rInInppuut/t1/010000V0V + 10M 511k SSaaffeettyypplluuggss 289k - 10M 511k AUX1 DDirireeccttInInppuutt//1100VV + TTeerrmmiinnaall Bblloocckkss - VVoollttaaggeeDDivividideerrIInnppuutt//11000000VV + 10M 511k SSaaffeettyy pplluuggss 289k - - Fluke 1736/B | Manual - Page 10
to extend any other warranty on Fluke's behalf. To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that Service Center with a description of the problem. THIS WARRANTY IS YOUR ONLY
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
PN 4749275
December 2015
©2015 Fluke Corporation. All rights reserved.
Specifications are subject to change without notification.
All product names are trademarks of their respective companies.
Auxiliary Input Adapter
for 17xx
Power and Energy Loggers
Instructions
Introduction
The Auxiliary Input Adapter (or Product) is an accessory for
the 17xx Power and Energy Loggers. It allows connection of
up to two sensors for analog measurements. These
measurements include temperature, pressure, and level with
an output voltage of 0 V dc to 10 V dc or a current loop of
4 mA to 20 mA (with additional shunt). Alternately, up to two
dc voltage inputs in the range of 1 V dc to 1000 V dc can be
used for other applications such as solar energy systems.
products online at:
1.877.
www.
MyFlukeStore
.com