Frigidaire AGQ7000EE Data Sheet

Frigidaire AGQ7000EE - 5.8 cu.ft. Affinity Gas Dryer Manual

Get Frigidaire AGQ7000EE - 5.8 cu.ft. Affinity Gas Dryer PDF manuals and user guides
UPC - 012505375514
View all Frigidaire AGQ7000EE manuals
Add to My Manuals
Save this manual to your list of manuals

Frigidaire AGQ7000EE manual content summary:

  • Frigidaire AGQ7000EE | Data Sheet - Page 1
    will beep and the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash. Troubleshoot the problem by using charts on the pages 3-5. Quick Check If there is no error displayed and the washer momentarily starts then turns back off: 1. Listen for a relay closure inside the motor control
  • Frigidaire AGQ7000EE | Data Sheet - Page 2
    not communicating with control board. Refer to test (4). E35 Pressure sensor indicates water overfill. Refer to test (5). E36 Console control board problem. Replace console control board. E38 Air chamber clogged or pressure sensor defective. Check air chamber, rpl press. sensor. E41 Control
  • Frigidaire AGQ7000EE | Data Sheet - Page 3
    control board. 1. Is the water level above 4.5 inches? 2. Does water enter the washer continuously. 3. Remove power from washer. Does the water stop coming in? 4. Replace the pressure sensor switch. Did this correct the problem? 1. Is the loading door closed? 2. In the J2 plug on the console control
  • Frigidaire AGQ7000EE | Data Sheet - Page 4
    ohms? Yes, check the wiring - if good, rpl console control board. Test 16: 1. Check the wiring harness between the console If defective, correct wiring problem. control board & the interface board. If the harness is good and none of the LEDs light, replace the interface board. If this does not
  • Frigidaire AGQ7000EE | Data Sheet - Page 5
    Feuille de données techniques de machine à laver Ces renseignements ne s'adressent qu'à des techniciens qualifiés ATTENTION : DÉBRANCHEZ L'ALIMENTATION ÉLECTRIQUE AVANT D'EFFECTUER TOUT ENTRETIEN Replacez cette feuille dans son enveloppe dans l'appareil pour référence ultérieure Contenu Page
  • Frigidaire AGQ7000EE | Data Sheet - Page 6
    Test de diagnostic Le test de diagnostic sert à vérifier uniquement le fonctionnement de composant individuel. POUR DÉMARRER LE TEST : • Tournez le bouton programme à la position démarrer, Essorage uniquement. • Appuyez sur Démarrer/pause pour démarrer le cycle et le sauvegarder. • Appuyez sur
  • Frigidaire AGQ7000EE | Data Sheet - Page 7
    Tableau de code d'erreur Code Défectuosité d'erreur Vérification E11 Durée de remplissage trop longue Référer au test (1) E13 Eau fuyant dans le tambour ou air fuyant dans la soufflette Référer au test (2) E21 Eau pompée trop lentement Référer au test (3) E23 Relais de la pompe de vidange
  • Frigidaire AGQ7000EE | Data Sheet - Page 8
    Test Test Vérification Test 1: 1. Est-ce que le flux d'entrée d'eau est normal ? Correction Oui. Passez à l'étape (4). Non. Passez à l'étape (2). 2. Est-ce que les robinets d'entrée d'eau sont ouverts ? Non. Ouvrez les robinets d'eau. Oui. Passez à l'étape (3) 3. Est-ce que la pression d'entr
  • Frigidaire AGQ7000EE | Data Sheet - Page 9
    tension. Test 7: 1. Commencez le test de diagnostic. Tournez le bouton de programmation de huit positions vers la droite à partir de la position de départ. Test 8: 1. Débranchez le raccord du moteur et mesurez la résistance des broches 4 et 5 du moteur. Non. Fermez la porte. Oui. Passez à l'étape
  • Frigidaire AGQ7000EE | Data Sheet - Page 10
    Hoja de Datos Técnicos de Lavadora Esta información es Sólo para Técnicos Calificados. PRECAUCIÓN: DESCONECTE LA CORRIENTE ELÉCTRICA ANTES DEL SERVICIO Por favor, conserve esta hoja en su sobre en el producto para referencia futura Contenido Página Explicación del código de error 10-11 Diagnó
  • Frigidaire AGQ7000EE | Data Sheet - Page 11
    Prueba de Diagnóstico La prueba de diagnóstico se usa para verificar sólo la función del componente individual. PARA COMENZAR LA PRUEBA: • Gire la Perilla de Programa hasta la posición inicio, Centrifugado Solamente. • Presione Inicio/Pausa para iniciar el ciclo y guardarlo. • Presione Cancelar para
  • Frigidaire AGQ7000EE | Data Sheet - Page 12
    Cuadro de códigos de error Código de error Condición de falla E11 Tiempo de llenado demasiado largo. E13 Filtración de agua en el tambor o filtración de aire en la campana de aire. E21 El agua no bombea hacia afuera a la velocidad suficiente. E23 El Relay de la bomba de dren en el tablero de
  • Frigidaire AGQ7000EE | Data Sheet - Page 13
    Test 1: 1. ¿Es normal el flujo entrante de agua? 2. ¿Están abiertas las bocas de entrada de agua? Sí. Vaya al paso (4). No. Vaya al paso (2) No. Abra las entradas de agua. Sí. Vaya al paso (3). 3. La presión de entrada de agua, ¿es superior a treinta (30) libras por pulgada cuadrada? 4. El agua
  • Frigidaire AGQ7000EE | Data Sheet - Page 14
    Test 6: Test 7: Test 8: 1. ¿Está cerrada la puerta de carga? No. Cierre la puerta. Sí. Vaya al paso (2). 2. En el enchufe J2 del control, mida el voltaje del cable negro a tierra con la alimentación encendida. 0 voltios. Verifique el cierre de la puerta. Si está en buen estado, cambie el
  • Frigidaire AGQ7000EE | Data Sheet - Page 15
  • Frigidaire AGQ7000EE | Data Sheet - Page 16
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Washer Tech Data Sheet
This information is intended for Qualified Technicians Only.
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING
Please Return This Sheet to its Envelope in the Product for Future Reference
Contents
Page
Error code explanation
..........................................
1
Diagnostics
...........................................................
1
Error Code Chart
...................................................
2
Tests
..................................................................
3-4
Français
.............................................................
5-8
Español
............................................................
9-14
6000 Wiring Diagram
...........................................
15
7000 Wiring Diagram
...........................................
16
READING ERROR CODES:
1. Wake the washer by pressing any button.
2. Wait 5 seconds.
3. Press and
HOLD
the
Start/Pause
and
Cancel
buttons simultaneously.
As long as the buttons are held, the failure code will appear in the display as an
E
followed by two numbers, a number and a letter or two letters. The
control will beep and the
Door Lock, Wash, Rinse,
and
Final Spin
indicator lights will flash.
T
roubleshoot the problem by using chart
s on the p
ages 3-5.
Quick Check
I
f there is no error displayed and the washer momentarily starts then turns back off:
1. Listen for a relay closure inside the motor control shortly after the
Start/Pause
key is pressed. If this happens, the motor control has power.
2. Check the 5 pin connector wiring between the console control and the motor control.
NOTE:
During normal operation, the display may show:
“
cd
” - cool down (Sanitary cycle)
“
do
” or “
dr
” - door problem.
“
Err
” - an error has been detected.
“
LOC
” - control lock is activated.
“
PAU
” - cycle has been interrupted.
To clear latest stored error code:
•
Turn the
Program Knob
to the
st
art position,
Spin Only.
•
Press
Start/Pause
to start the cycle and save it.
•
Press
Cancel
to stop the cycle and turn off the LEDs.
•
Press
Cancel
again to turn on the LEDs.
•
Within 5 seconds, press and hold the
Option
and
Start/Pause
buttons until LEDs start sequentially chasing, then release buttons.
•
Turn the program knob clockwise 7 clicks from the
S
t
art Position. The control will signal the last error code.
•
Press and hold the
Options
and
Start/Pause
buttons for 3 seconds. The code will be cleared.
•
Exit Diagnostic Mode to return the washer to normal operation.
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob clockwise 2 or 3 clicks after the
S
t
art Position. Press
Options
and
Start/Pause
buttons together for a few seconds
until wash cycle LEDs appear.
Diagnostic Test
The diagnostic test is used to check individual component function only.
T
O ST
ART THE TEST
:
•
Turn the
Program Knob
to the
st
art position,
Spin Only.
•
Press
Start/Pause
to start the cycle and save it.
•
Press
Cancel
to stop the cycle and turn off the LEDs.
•
Press
Cancel
again to turn on the LEDs.
•
Within 5 seconds, press and hold the
Options
and
Start/Pause
buttons until LEDs start sequentially chasing, then release buttons.
1.
All the LEDs will sequentially light. Pressing a button below a light cluster will light all the LEDs in that cluster at one time to confirm functionality.
2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should enter through the
detergent compartment.
3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter through the bleach
compartment.
4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold water should enter
through the softener compartment.
5.
Turn the program knob (4) clicks from the start position. The door lock solenoid will deactivate and the loading door can be opened. When the door
is opened, the drum light should turn on.
6. Turn the program knob (5) clicks from the start position. The washer will fill and tumble. Once tumbling has started, the Boost Heater (if so
equipped) will turn on.
7.
Turn the program knob (6) clicks from the start position. The drain pump & door lock solenoid will activate and the washer will operate in high spin.
SAFETY
W
ARNING:
If power is removed during this test, the door can be opened. To prevent injury,
DO NOT
put your hands inside when the tub
is rotating.
8. Turn the program knob (7) clicks from the start position. The control will signal the last error code.
Exiting Diagnostic Mode
There are two options for exiting the Diagnostic Test mode and returning the washer to normal operation:
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob clockwise 2 or 3 clicks after the
start position. Press
Options
and
Start/Pause
buttons together for a few seconds until
wash cycle LEDs appear.
If a situation arises where you cannot exit the Diagnostic mode as described above and the bank of 5 LED’s on the right end remain ON
regardless of Program Knob position, a combination of pushed buttons may have caused the control to enter a special factory test
mode. Disconnect power to reset the control to return washer to normal operation is this occurs.
137063900
C
(
1202
)