Frigidaire FAFS4272LW Wiring Diagram (All Languages)
Frigidaire FAFS4272LW Manual
UPC - 012505382208
View all Frigidaire FAFS4272LW manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FAFS4272LW manual content summary:
- Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 1
16 Acronyms: MB - Main Board (Board located inside machine on right side just behind control panel.) MC - Motor Control UI - User interface board (board located inside the front control panel) DL - Door Lock READING ERROR CODES 1. Wake the washer up by pressing any button (except the cancel button - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 2
the wash water solenoids will deactivate and the loading door can be opened. spin, press the Delay Start key. 10. Turn the program knob (9) clicks from the start position. The control Exiting Diagnostic Mode To return the washer to normal operation display models, wake machine, push the spin speed - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 3
failure. Door PTC Sensing Open Door PTC Sensing Closed Door PTC Sensing Problem Bad signal from tacho generator. Low Voltage to Motor Control Board. Over speed. Under speed. High current on inverter. High current on motor phase. No tacho signal for 3 seconds. High temperature on heat sink caused - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 4
sensor and the main control board. Test 5 1. Is the water level above 4.5 inches? 2. Does water enter the washer continuously? 3. Remove power from washer. Does the water stop coming in? 4. Replace the pressure sensor switch. Did this correct the problem? Test 6 1. Is the loading door closed? 2. Can - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 5
If the readings are correct, check wiring from motor to motor control board, If good, replace the motor control board.If the readings are incorrect, replace the motor. Test 9: 1. Remove the belt from the motor and spin the motor pulley. Does the motor spin free? 2. Spin the tub pulley. Does the tub - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 6
la commande se ferme peu de temps après avoir appuyé sur la touche "Start (Départ)/Pause". 2. Vérifiez si les connexions de la MB sont ajustées fermement. Pour effacer moire : • Appuyez sur le bouton CANCEL (Annuler) pour passer en mode de veille et activer l'entrée de diagnostic. • Dans les 10 - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 7
cas échéant, tournez le bouton de programmation de onze (11) positions à partir de la position de départ. Il s'agit d'une position normale. Quitter le mode diagnostic Pour refaire fonctionner normalement la laveuse : a) Débranchez le cordon d'alimentation, attendez 5 à 8 secondes, puis rebranchez le - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 8
Tableau des codes d'erreur Code d'erreur Anomalie Vérification E11 Durée de remplissage trop longue. Se référer au test (1). E13 Fuite d'eau dans la cuve ou fuite d'air dans la cloche d'air. Se référer au test (2). E21 Eau pompée trop lentement. Se référer au test (3). E25 Relais du - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 9
3. Vérifiez le câblage entre le verrou de la porte et le Si OK, passez à l'étape 4. panneau de commande principal. 4. Programmez la laveuse en mode « Rinse Spin » (Rinçage/essorage) et enlevez les articles qui pourraient se trouver dans la cuve. Démarrez le cycle. Est-ce que l'eau s'évacue? Si NON - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 10
Test Test Vérification Correction Test 7 1.Débranchez le raccord du moteur et mesurez la résistance des broches 4 et 5 du moteur. Si la valeur lue se situe entre 105 et 130 Ohms, remplacez la carte de contrôle de moteur.Si le compteur indique d'autres valeurs que 105 et 130 Ohms, remplacez le - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 11
principal (tarjeta localizada dentro de la máquina al lado derecho justo detrás del panel de control). MC - Control de motor UI - Tarjeta de Interfaz de Usuario (tarjeta localizada dentro del panel de control delantero) DL - Seguro de la puerta LECTURA DE CÓDIGOS DE ERROR 1. Ponga la lavadora en - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 12
el centrifugado rápido, oprima la tecla "Delay Start" (encendido diferido). 10. Gire la perilla de programa a 9 posiciones desde la posición de inicio. El control indicará los últimos cinco códigos de error (E00 significa que no hay error). 11. Gire la perilla de programa a 10 posiciones desde la - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 13
bomba de recirculación E26 Relé de bomba de recirculación E31 Falla del interruptor electrónico de presión. E32 Problema con la calibración del sensor de presión. E35 . E53 Voltaje bajo hacia el tablero de control del motor. E54 Velocidad excesiva. E55 Velocidad insuficiente. E57 Corriente elevada en el - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 14
agua en la lavadora? 2.¿Hay fuga de aire en el sistema de la campana de aire? 3.Cambie el sensor de presión. 4.Cambie la tarjeta de control principal. 1.Compruebe que la manguera de drenado no esté obstruida. 2.Inicie la lavadora y compruebe que hay 120 V de CA en la bomba de drenado. Inspeccione - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 15
bueno. Cambie la tarjeta de interfaz del usuario. Si el problema no se corrige, cambie la tarjeta de control principal. Si está correcto, para el código de error E5C, cambie la tarjeta de control de motor. Si está correcto, para los códigos de error EA1, EA2, EA3, EAE o EA5, cambie la tarjeta de - Frigidaire FAFS4272LW | Wiring Diagram (All Languages) - Page 16
Tech Data Sheet Part No. 137309200
137309200A
(1003)
Washer Tech Data Sheet
This information is intended for Qualified Technicians Only.
CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING
Please Return This Sheet to its Envelope in the Product for Future Reference
Contents
Page
Error code explanation
.............................................
1
Diagnostics
........................................................
1-2
Error Code Chart
.....................................................
3
Tests
..................................................................
4-5
Français…………………………………………
.........
6-10
Español…………………………………………
........
11-15
Wiring Diagram……………………………………
........
16
Acronyms:
MB – Main Board (Board located inside machine on right side just behind control panel.)
MC – Motor Control
UI – User interface board (board located inside the front control panel)
DL – Door Lock
READING ERROR CODES
1.
Wake the washer up by pressing any button (except the cancel button).
2.
Press and hold the
“cancel
”
and
“start”
buttons simultaneously for 6 seconds. The failure code will appear in the
display as an E followed by two numbers.
NOTE:
E00 means no failure code experienced.
Troubleshoot the problem by using charts on the pages 3-5.
If there is no error displayed and the washer momentarily starts then turns back off:
1.
Listen for a relay closure inside the control shortly after the
“start/pause”
key is pressed.
2.
Check the connections on the MB make sure that they are firmly snug and secured.
To clear latest stored error code:
•
Press the
“cancel”
button to enter standby mode and enable diagnostic entry.
•
Within 10 seconds after pressing
“cancel”
, press any button (except the cancel button) to wake up the control.
•
Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the
“cancel
”
and
center
button under the display
simultaneously for 3 seconds to enter the Diagnostic Mode.
(note: to save time at wake up,
the welcome screen can be bypassed by turning the selector knob).
•
Turn the program knob clockwise 9 turns (clicks) from the
S
t
art Position. The control will signal the last 5 error codes with
E00 meaning no error experienced.
•
Press and hold the
center key under the display
and
“cancel”
buttons simultaneously for 3 seconds. The code(s) will
be cleared.
•
To return the washer to normal operation.
a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b) Turn the program knob clockwise 2 turns (clicks) back to the
S
t
art Position (LEDs are flashing).
Press the
“cancel
” and
center button under the display
until the LEDs stop flashing.
Diagnostic Test
The diagnostic test is used to check individual component functio
n only.
T
O ST
ART THE TEST
:
•
Press the
“cancel”
button to enter standby mode and enable diagnostic entry.
•
Within 10 seconds after pressing
“cancel”
, press any button (except the cancel button) to wake up the control.
•
Within 5 seconds of wake up, turn the selector knob to the far left cycle and press and hold the
“cancel”
and
the center
button under the display
simultaneously for 3 seconds to enter the Diagnostic Mode.
(note: to save time a
t wake up,
the welcome screen can be bypassed by turning the selector knob).
1.
Upon entering Diagnostic Mode, all lights should flash for 1¼”x2” display models.