Frigidaire FAQE7001LB Installation Instructions (All Languages)
Frigidaire FAQE7001LB Manual
View all Frigidaire FAQE7001LB manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FAQE7001LB manual content summary:
- Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 18-21 Installation Requirements 4-10 Accessories 22 Installed Dryer Dimensions 11 Español 23 Installation Instructions 12-17 137112200C (1004) - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 2
the risk of fire. • Do not stack a dryer on top of washer already installed on pedestal. Do not stack washer on top of dryer. Do not stack washer on top of another washer. • The instructions in this manual and all other literature included with this dryer are not meant to cover every possible - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 3
240v Electric Supply (Electric Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide Test hinge and latch - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 4
or closed loop connectors and marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM. 4-WIRE POWER SUPPLY CORD KIT (not supplied) 4-wire receptacle (NEMA type 14-30R) The dryer MUST employ a 4-conductor power supply cord NEMA 14-30 - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 5
dryer Current. POWER SUPPLY CORD - The dryer is equipped with a 120 volt flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be connection to the dryer. 6 The dryer MUST be disconnected 1/2 psig (3.45 kPa). 7 The dryer MUST be isolated from the gas supply - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 6
or any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following are obstruct clothes dryer airflow and increase the risk of fire. If your present system is made up of plastic duct or metal foil duct, replace it with - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 7
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 8
quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware acceptable. If the manometer reading is higher than .075 inches of water column, the system is too restrictive and the installation is unacceptable - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 9
Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support guide for other important exhaust venting system requirements. 5 When installing a gas dryer YOUR DRYER: 1 In an area exposed to dripping water or - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 10
appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer , a quick-turn 90° dryer vent elbow (vented right or down in freestanding dryer or right on pedestal-mounted dryer) must be installed to achieve - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 11
) adds approximately 0.75 in. (2 cm) to installation depth. Upward venting of exhaust on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust on stacked dryer adds approximately 2.25 in. (6.5 cm) to installation depth. Leftward venting of exhaust on - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 12
can create electrical shock and/or a fire hazard. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 13
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 14
INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit manual shutoff valve. This valve should be located in the same room as the dryer dryer - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 15
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 16
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 17
. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are located inside - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 18
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 19
Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. ROUND PLUG REVERSING DOOR 4 From the back side of - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 20
hole in the outer door. 3 Replace indented head screws (no. 1-5) removed earlier. Take care not to strip out the plastic holes. 4 Replace pan head screws (no. 6-7) 5 Locate new metal strike supplied with dryer manuals. Grip new strike with pliers as shown below. Firmly insert the strike so it - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 21
holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 22
purchased your dryer. Replacement parts: If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your Use and Care Guide for more information. 22 WARNING ELECTRICAL SHOCK HAZARD Label all wires prior to disconnection when servicing controls - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 23
Instrucciones de instalación 34-39 Requisitos de instalación 26-32 Inversión de la puerta 40-43 Dimensiones de la secadora instalada 33 Accesorios 44 www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352 - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 24
el CSA C22.1 del Código Eléctrico de Canadá (Canadian Electrical Code) Parte 1. • El servicio de gas de la secadora debe cumplir con los có Conducto de escape de metal rígido o semirígido de 4 pulgadas (102 mm) • Kit de cables de alimentación trifilar o tetrafilar de 240 voltios (secadora eléctrica) - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 25
palabras y avisos de seguridad Las indicaciones de seguridad incluidas en este manual aparecen precedidas de un aviso titulado "ADVERTENCIA" o "PRECAUCIÓN", de selladas con un sellante aprobado y bien apretadas con una llave Kit de conversión para el sistema de gas LP Suministro de gas - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 26
REQUISITOS DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos elé - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 27
REQUISITOS DE INSTALACIÓN Requisitos eléctricos de la secadora a gas: CIRCUITO - Circuito individual de bifurcación de 15 amp., correctamente polarizado y con conexión a tierra con fusible de retardo de 15 amp. o con interruptor automático. SUMINISTRO ELÉCTRICO: corriente alterna de 2 cables, con - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 28
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 10,2 cm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 29
de incendio. • No bloquee los extremos de escape del sistema de ventilación, ni utilice tornillos, remaches ni otros sujetadores que se extiendan hacia la parte interna del conducto para ensamblarlo. Es posible que la pelusa quede atrapada en el filtro, los tornillos o los remaches, lo que puede - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 30
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 31
de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad anclar esta secadora (1) o secadora sobre pedestal (2) al piso usando un kit de instalación para casas rodantes, pieza número 137067200. Requisitos de despeje - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 32
(387.1cm²) 1" (2.54cm) 0" (0cm) 32 3" (7.6cm) puerta del armario 60 sq. in. (387.1cm²) Í NOTA Para lograr una instalación con 0 cm (0") de despeje en la parte trasera de la secadora (para otra que no sea la ventilación hacia atrás), se debe instalar un codo de ventilación de giro rápido de 90 - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 33
del piso 51.25" (130cm) tubería de suministro de gas en la parte trasera de la unidad de gas 1.6" (4cm) 16.9" (43cm) * el centro de la ventilación trasera 27.0" (68.5cm) suministro eléctrico en la parte trasera de la unidad altura de la línea central para ventilación trasera 3.7" (9.5cm) 19.0" - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 34
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 35
INSTRUCCIONES DE INSTALACIÓN Requisitos de conexión a tierra: secadora eléctrica (Canadá) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Una conexión incorrecta del conductor de conexión a tierra del equipo puede provocar un peligro de descarga eléctrica. Si no está seguro de haber realizado - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 36
de gas en la parte trasera de la secadora. IMPORTANTE NO conecte la secadora al servicio de gas LP sin convertir la válvula de gas. El kit de conversión a gas de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector flexible Tubo de admisión en la parte posterior de la - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 37
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 38
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 39
cuidadosamente. Ajuste una o varias de las patas de la secadora hasta que se encuentre firme sobre las cuatro patas. Coloque un nivel en la parte superior A de la secadora. La secadora DEBE estar nivelada y firme sobre las cuatro patas. Presione las distintas esquinas para asegurarse de que la - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 40
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 41
de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN REDONDO TAPÓN CUADRADO INVERSIÓN DE LA PUERTA 4 Desde la parte trasera de la puerta interior, presione las lengüetas de retención del tapón de plástico cuadrado para liberarlo. Guarde el tapón cuadrado para - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 42
del recorte de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 43
Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 44
altura total de 134,62 cm (53 pulgadas). *Es posible que hayan otros colores disponibles. Póngase en contacto con el distribuidor donde adquirió la secadora. KIT DE SECADORA PARA CENTRO DE LAVADO Pieza No.. 134700600 Dependiendo del modelo que haya comprado, es posible que esta secadora incluya un - Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 45
- Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 46
- Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 47
- Frigidaire FAQE7001LB | Installation Instructions (All Languages) - Page 48
All about the
Installation
of your
Dryer
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-17
Reversing Door
..............................................
18-21
Accessories
.........................................................
22
EspaƱol
..............................................................
23
TABLE OF CONTENTS
137112200C (1004)