Frigidaire FASE7073NW Installation Instructions (All Languages)
Frigidaire FASE7073NW Manual
View all Frigidaire FASE7073NW manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FASE7073NW manual content summary:
- Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 20-23 Installation Requirements 4-10 Accessories 24 Installed Dryer Dimensions 11 Español 25 Installation Instructions 12-19 137442700A (1104) - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 2
known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire. • The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 3
240v Electric Supply (Electric Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide Test hinge and latch - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 4
or closed loop connectors and marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM. 4-WIRE POWER SUPPLY CORD KIT (not supplied) 4-wire receptacle (NEMA type 14-30R) The dryer MUST employ a 4-conductor power supply cord NEMA 14-30 - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 5
Z223.1 (latest edition). 2 The gas supply line should be 1/2 inch (1.27 cm) pipe. 3 If codes allow, flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be constructed of stainless steel or plastic-coated brass. 4 The gas supply line MUST have an individual - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 6
or any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire. If your present system - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 7
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 8
an increase in vent restriction. • The exhaust system should be inspected and cleaned a minimum of every 18 months with normal usage. The more the dryer is used, the more often you should check the exhaust system and vent hood for proper operation. See also CLEARANCE REQUIREMENTS on the next page - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 9
CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal dryer exhaust outlet. 6 Installer MUST anchor this (1) dryer or (2) dryer mounted on pedestal to the floor with approved Mobile Home Installation Kit - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 10
outdoors. 2 No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum of 120 square inches (774.2 cm - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 11
) freestand dryer on floor floor line 51.25" (130cm) dryer mounted on optional pedestal floor line * To obtain these minimal depth dimensions, dryer must be on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust on stacked dryer adds approximately - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 12
• This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 13
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1 The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 14
INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit approved manual shutoff valve. This valve should be located in the same room as the dryer and - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 15
INSTALLATION INSTRUCTIONS Water connection (Steam Model only) WATER SUPPLY REQUIREMENTS Cold water faucet MUST be installed within 42 inches (107 cm) of your dryer's any contaminants in the line. 4 Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers. RUBBER - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 16
INSTRUCTIONS Water connection, continued (Steam Model pliers. 9 Connect the straight end of the long hose from the kit to the other outlet on the "Y" connector and snug it by hand inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 17
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 18
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 19
time and money. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 20
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 21
Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. ROUND PLUG REVERSING DOOR 4 From the back side of - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 22
no. 1-5 no. 6-7 2 Rest the opening of the inner door at a 90 degree angle on the supports for the hinge cutout cover. Pivot the inner door down onto the outer door. 5 Locate new metal strike supplied with dryer manuals. Grip new strike with pliers as shown below. Firmly insert the strike so it is - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 23
holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 24
. This pedestal will add about 15" (38 cm) to the height of your unit for a total height of 51.25" (130 cm). *Other colors may be available. Contact the source where you purchased your dryer. DRYER STACKING KIT P/N STACKIT4X Depending on the model you purchased, a kit for stacking this dryer on top - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 25
Instrucciones de instalación 36-43 Requisitos de instalación 28-34 Inversión de la puerta 44-47 Dimensiones de la secadora instalada 35 Accesorios 48 www.frigidaire.com UEES.AU1U-8.10-08-0904-49-4940-494044 wwwww.fwrig.firdigaidrea.icrea.caCanCaadnaad1á-810-08-0206-52-6853-582352 25 - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 26
el CAN/CGA B149,1-2000. Se debe instalar una válvula de cierre individual manual a una distancia no mayor a 1,83 m (6 pies) de la secadora Conducto de escape de metal rígido o semirígido de 4 pulgadas (102 mm) • Kit de cables de alimentación trifilar o tetrafilar de 240 voltios (secadora eléctrica) - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 27
palabras y avisos de seguridad Las indicaciones de seguridad incluidas en este manual aparecen precedidas de un aviso titulado "ADVERTENCIA" o "PRECAUCIÓN", de selladas con un sellante aprobado y bien apretadas con una llave Kit de conversión para el sistema de gas LP Suministro de gas - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 28
REQUISITOS DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos elé - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 29
REQUISITOS DE INSTALACIÓN Requisitos eléctricos de la secadora a gas: CIRCUITO - Circuito individual de bifurcación de 15 amp., correctamente polarizado y con conexión a tierra con fusible de retardo de 15 amp. o con interruptor automático. SUMINISTRO ELÉCTRICO: corriente alterna de 2 cables, con - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 30
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 102 mm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 31
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) ADVERTENCIA PELIGRO DE INCENDIO Una secadora de ropa debe tener ventilación al exterior. No ventile la secadora a una chimenea, pared, techo, ático, pasajes entre pisos ni ningún espacio oculto de la vivienda. Las secadoras - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 32
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 33
del área de la salida de escape de la secadora. 6 El técnico de instalación DEBE anclar esta secadora (1) o secadora sobre pedestal (2) al piso usando un kit de instalación para casas rodantes, pieza número 137067200. Requisitos de despeje ADVERTENCIA PELIGRO DE EXPLOSIÓN No instale la secadora en - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 34
REQUISITOS DE INSTALACIÓN Requisitos de despeje (continuación) Instalación en un Nicho o Armario 1 Una secadora instalada en un dormitorio, baño, nicho o armario, DEBE tener ventilación al exterior. 2 No se debe instalar ningún otro artefacto de combustión en el mismo armario que la secadora a gas. - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 35
nea del piso 51.25" (130cm) tubería de suministro de gas en la parte trasera de la unidad de gas 1.6" (4cm) secadora colocada sobre pedestal opcional línea del piso * Para obtener estas dimensiones mínimas de profundidad, la secadora debe ser ventilada derecho hacia atrás. Si se usa un codo de - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 36
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 37
INSTRUCCIONES DE INSTALACIÓN Requisitos de conexión a tierra: secadora eléctrica (Canadá) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Una conexión incorrecta del conductor de conexión a tierra del equipo puede provocar un peligro de descarga eléctrica. Si no está seguro de haber realizado - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 38
la secadora al servicio de gas LP sin convertir la válvula de gas. El kit de conversión a gas LP debe ser instalado por un técnico calificado. 2 conexiones de los tubos. FLUJO DE GAS Válvula de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector flexible Tubo de - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 39
suministro de agua FRÍA y deje correr el agua en un balde o recipiente para limpiar cualquier contaminante que esté presente en la tubería. 4 Retire el kit de manguera del tambor de la secadora e inspeccione los accesorios de la manguera para asegurarse de que las arandelas de goma estén en su lugar - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 40
ón de agua FRÍA al conector en "Y" y apriétela a mano. Luego apriétela 2/3 de vuelta más usando alicates 9 Conecte el extremo recto de la manguera larga del kit a la otra salida del conector en "Y" y apriételo a mano. Conecte el codo de 90° de la manguera a la admisión de agua de latón en la - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 41
INSTRUCCIONES DE INSTALACIÓN Conexión eléctrica (fuera de Canadá): trifilar Receptáculo trifilar (tipo NEMA 10-30R) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA El no desconectar el suministro eléctrico antes de realizar cualquier reparación puede ocasionar lesiones personales o incluso la muerte. 1 - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 42
INSTRUCCIONES DE INSTALACIÓN Conexión eléctrica (fuera de Canadá): tetrafilar Receptáculo tetrafilar (tipo NEMA 14-30R) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA El no desconectar el suministro eléctrico antes de realizar cualquier reparación puede ocasionar lesiones personales o incluso la muerte. - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 43
INSTRUCCIONES DE INSTALACIÓN Instalación general 1 Conecte el tubo de escape al sistema de escape exterior (consulte las páginas 54 a 56). Se recomienda usar una abrazadera (pieza A) de 4" (10,2 cm) para conectar las secadora al sistema de ventilación de escape. Utilice cinta de papel de aluminio - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 44
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de la bisagra. Retire el tornillo inferior primero y - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 45
Inversión de la bisagra 1 Retire cuidadosamente los dos tapones redondos del panel delantero y guárdelos. Retire y guarde la cubierta cuadrada de la ranura en forma de "T" deslizándola hacia arriba y tirando de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 46
de la cubierta de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 47
Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA DE "T" EN LA - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 48
se puede utilizar para elevar la secadora y facilitar su uso. Dicho pedestal agregará aproximadamente 38,1 cm (15 pulgadas) a la altura de su . Póngase en contacto con el distribuidor donde adquirió la secadora. KIT DE SECADORA PARA CENTRO DE LAVADO Pieza No. STACKIT4X Dependiendo del modelo - Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 49
- Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 50
- Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 51
- Frigidaire FASE7073NW | Installation Instructions (All Languages) - Page 52
All about the
Installation
of your
Dryer
137442700A (1104)
TABLE OF CONTENTS
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-19
Reversing Door
..............................................
20-23
Accessories
.........................................................
24
EspaƱol
..............................................................
25