Frigidaire FASE7074LA Installation Instructions (All Languages)
Frigidaire FASE7074LA Manual
UPC - 012505382499
View all Frigidaire FASE7074LA manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FASE7074LA manual content summary:
- Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 18-21 Installation Requirements 4-10 Accessories 22 Installed Dryer Dimensions 11 Español 23 Installation Instructions 12-17 137336900A (1003) - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 2
of another washer. • The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance. WHAT TO DO IF - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 3
Gas Supply (Gas Dryer) Manual shutoff valve present Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 4
dryer is internally grounded to neutral unless it was manufactured for sale in Canada. Only a 4-conductor cord shall be used when the appliance closed loop connectors and marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM. 4- - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 5
dryer Current. POWER SUPPLY CORD - The dryer is equipped with a 120 volt flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be connection to the dryer. 6 The dryer MUST be disconnected 1/2 psig (3.45 kPa). 7 The dryer MUST be isolated from the gas supply - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 6
or any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following are obstruct clothes dryer airflow and increase the risk of fire. If your present system is made up of plastic duct or metal foil duct, replace it with - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 7
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 8
Exhaust direction Directional exhausting can be accomplished by installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store. CORRECT INCORRECT In installations where the exhaust system is - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 9
Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support to previous sections in this guide for other important exhaust venting system requirements. 5 When installing a gas dryer into a mobile home, a - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 10
or closet, MUST be exhausted outdoors. 2 No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 11
for rear vent 37" (94cm) drain hose on rear of unit3 power cord on rear of unit2 39" (99cm) * To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to installation depth. Upward venting of exhaust on - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 12
can create electrical shock and/or a fire hazard. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 13
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 14
INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service be equipped with an approved manual shutoff valve. This valve should be located in the same room as the dryer and should be in a location - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 15
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 16
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 17
time and money. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 18
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 19
Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. ROUND PLUG REVERSING DOOR 4 From the back side of - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 20
-hand hinge. 3 Replace indented head screws (no. 1-5) removed earlier. Take care not to strip out the plastic holes. 4 Replace pan head screws (no on the supports for the hinge cutout cover. Pivot the inner door down onto the outer door. 5 Locate new metal strike supplied with dryer manuals. Grip - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 21
holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 22
. Replacement parts: If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your Use and Care Guide for more information. 22 WARNING ELECTRICAL SHOCK HAZARD Label all wires prior to disconnection when servicing controls. Wiring errors can - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 23
Instrucciones de instalación 34-39 Requisitos de instalación 26-32 Inversión de la puerta 40-43 Dimensiones de la secadora instalada 33 Accesorios 44 www.frigidaire.com UEES.AU1U-8.10-08-0904-49-4940-494044 wwwww.fwrig.firdigaidrea.icrea.caCanCaadnaad1á-810-08-0206-52-6853-582352 23 - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 24
Eléctrico Nacional (National Electrical Code), el ANSI/NFPA 70, o bien en Canadá, el CSA C22.1 del Código Eléctrico de Canadá (Canadian Electrical Code) Parte 1. • El servicio de gas de la secadora debe cumplir con los códigos y las ordenanzas locales, y la última edición del Código de Gas Nacional - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 25
instrucciones antes de usar este secadora. Identificación de los símbolos, palabras y avisos de seguridad Las indicaciones de seguridad incluidas en este manual aparecen precedidas de un aviso titulado "ADVERTENCIA" o "PRECAUCIÓN", de acuerdo con el nivel de riesgo. Definiciones Este es el símbolo de - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 26
REQUISITOS DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos elé - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 27
REQUISITOS DE INSTALACIÓN Requisitos eléctricos de la secadora a gas: CIRCUITO - Circuito individual de bifurcación de 15 amp., correctamente polarizado y con conexión a tierra con fusible de retardo de 15 amp. o con interruptor automático. SUMINISTRO ELÉCTRICO: corriente alterna de 2 cables, con - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 28
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 102 mm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 29
de incendio. • No bloquee los extremos de escape del sistema de ventilación, ni utilice tornillos, remaches ni otros sujetadores que se extiendan hacia la parte interna del conducto para ensamblarlo. Es posible que la pelusa quede atrapada en el filtro, los tornillos o los remaches, lo que puede - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 30
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 31
Instalación en una casa rodante 1 La instalación DEBE cumplir con la actual Norma de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad y Construcción de Casas Rodantes [Federal Standard for Mobile Home Construction - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 32
ventilación distribuidas uniformemente en toda la superficie. ESPACIOS MÍNIMOS PARA LA INSTALACIÓN: cm (pulgadas) LATERALES PARTE TRASERA PARTE PARTE SUPERIOR DELANTERA Alcôve 0 cm (0") 0 cm (0") 0 cm (0") n/d Sous le comptoir 0 cm (0") 0 cm (0") 0 cm (0") n/d Placard 0 cm (0") 0 cm - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 33
cerrada 16.9" (43cm) 3.75" (9.5cm) 13.50" (34.5cm) hacia el centro de la ventilación trasera 27.0" (68.5cm) suministro eléctrico en la parte trasera de la unidad altura de la línea central para ventilación trasera 3.7" (9.5cm) 19.0" (48cm) 71.5" (182cm) conexión del suministro de agua en la - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 34
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 35
INSTRUCCIONES DE INSTALACIÓN Requisitos de conexión a tierra: secadora eléctrica (Canadá) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Una conexión incorrecta del conductor de conexión a tierra del equipo puede provocar un peligro de descarga eléctrica. Si no está seguro de haber realizado - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 36
gases licuados en todas las conexiones de los tubos. FLUJO DE GAS Válvula de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector flexible Tubo de admisión en la parte posterior de la secadora Todas las conexiones deben estar ajustadas con llave IMPORTANTE La línea - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 37
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 38
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 39
cuidadosamente. Ajuste una o varias de las patas de la secadora hasta que se encuentre firme sobre las cuatro patas. Coloque un nivel en la parte superior A de la secadora. La secadora DEBE estar nivelada y firme sobre las cuatro patas. Presione las distintas esquinas para asegurarse de que la - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 40
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 41
de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN REDONDO TAPÓN CUADRADO INVERSIÓN DE LA PUERTA 4 Desde la parte trasera de la puerta interior, presione las lengüetas de retención del tapón de plástico cuadrado para liberarlo. Guarde el tapón cuadrado para - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 42
de la cubierta de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 43
Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 44
ACCESORIOS PEDESTAL DE ALMACENAMIENTO CONCORDANTE* Pedestal de color blanco - P/N CFPWD15W Pedestal de color azul - P/N CFPWD15N Pedestal de color rojo - P/N CFPWD15R Pedestal de color plateada - P/N CFPWD15A Pedestal de color negra - P/N CFPWD15B Un accesorio de pedestal de almacenamiento, - Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 45
- Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 46
- Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 47
- Frigidaire FASE7074LA | Installation Instructions (All Languages) - Page 48
All about the
Installation
of your
Dryer
137336900A (1003)
TABLE OF CONTENTS
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-17
Reversing Door
..............................................
18-21
Accessories
.........................................................
22
EspaƱol
..............................................................
23